your thoughts on the pocket holes in a drawer are correct, always "inset" the front of a drawer into the sides as its less likely to pull off after year of opening and closing. i really your what i've learned videos. thanks for the content
Nice work I really enjoy your videos! I prefer to see the pocket holes on the ather part of the drawer so you could hide them behind the drawer front.. Thanks!
I have been using a pocket hole technique I call "pocket hole toe nailing". put screws in from both sides and the opposing angles give the screws a lot more holding power. I did a video on this call "what is the strongest plywood joint" if interested. keep up the great videos :>)
As shown the drawers the pocket hole method is weak as you said. Angling the holes with the thread closer to the end of the mating joint makes them even weaker! I now make my drawers with biscuits, with the sides overlapping the front and back so the shock does not pull on the joint repeatedly. Building this way I have not had a problem even in heavy tool drawers, supporting much more than I should jam into some of these drawers. I will be building my own table saw station for my workshop rebuilding.
I made my drawers with pocket holes at the back and front of the drawers, that way the drawer front will hide the front pocket holes and no one will see the back pocket holes. Also makes the sides look clean.
Hi Andreas, pocket holes and glue is ok since is on sliders, that takes out some stress compared to drawers that rest or have direct contact with wood that add friction to the weight.
Have you considered partially enclosing your GTS10XC to get better dust collection? - I have been experimenting with strips of foam at the various gaps to try to reduce the dust that escapes the vacuum, which works reasonably well but nowhere near perfect.
Hallo Andreas, klasse Video. Gute Tipps. Vielleicht könnte man noch mehr darauf eingehen, wie man die Schubladen baut und EINBAUT. Wie breit sollte die Lade sein relativ zur Breite des Korpus? Sollte man zuerst die Laufschienen montieren und dann die Lade entsprechend der verbleibenden Breite bauen? Ich weiss, dass die Vielfalt der verfügbaren Auszüge das Thema sehr komplex machen könnte, aber es gibt nach meiner kurzen Erfahrung noch viel zu sagen... Vielleicht ein zusätzliches Video? Nach meiner Erfahrung sitzen die Pocketholes so bombenfest, dass man hier nichts befürchten muss. Auch ein guter Hinweis zur Staubbildung und wie man es vermeidet, dass der Staub in die Schublade gelangt! Weiter so! Vielen dank, dij-w-a
Hi Andreas! Was hast du für ein Holzöl genommen? Die Schubladen sind super geworden, ich hoffe, mir bald selbst einen kreissägen Unterschrank zu bauen. Weiter so!
Ja, staubdichte Schubladen.... ein altes bis heute nicht wirklich gelöstes Thema. Zumindest im DIY-Bereich. Und ja, ich hatte mich gleich bei den ersten Aufnahmen mit den Taschenlöchern gewundert, warum an der Seite? Da sieht man die doch. Aber, dachte ich, sind ja Werkstattschubladen. Kommt nicht drauf an. An die Winkelbelastung ist aber sicher zu denken. Da hast du sicher recht. Aber die Schubladen fügen sich gut in den Schrank, wie wenn sie schon immer da gewesen wären.
Tja, Alfred. Leider ist mir das mit den sichtbaren Taschenlöchern auch erst später aufgefallen ;-) Aber deswegen mache ich neue Dinge gern zuerst für die Werkstatt, da ist es nicht tragisch, wenn man durch die Fehler lernen muss. Danke und beste Grüße, Andreas
hallo nochmal Andreas... die Griffe der Schubladen ein bisschen tiefer angebracht und kein Staub fällt mehr in die Schublade hinein... Grüße ins Markgräfler Land Thilo
Thanks for your feedback, in British English (and other British-based variants around the world) it’s actually learnt: en.wiktionary.org/wiki/learnt#English
Nice review Andreas. Great series.
Thanks!
Very comfortable table for saw!
Thanks for your feedback Aleksey.
your thoughts on the pocket holes in a drawer are correct, always "inset" the front of a drawer into the sides as its less likely to pull off after year of opening and closing. i really your what i've learned videos. thanks for the content
Thanks for your feedback, Dave.
Nice work I really enjoy your videos! I prefer to see the pocket holes on the ather part of the drawer so you could hide them behind the drawer front.. Thanks!
Thanks John. Hiding them is indeed also a good aspect. I will keep that in mind.
I have been using a pocket hole technique I call "pocket hole toe nailing". put screws in from both sides and the opposing angles give the screws a lot more holding power. I did a video on this call "what is the strongest plywood joint" if interested. keep up the great videos :>)
Thanks for the tip. I’ll check it out.
The separate “what I learnt “ works well.
Thanks for your feedback, Richard. I think so too.
As shown the drawers the pocket hole method is weak as you said. Angling the holes with the thread closer to the end of the mating joint makes them even weaker! I now make my drawers with biscuits, with the sides overlapping the front and back so the shock does not pull on the joint repeatedly. Building this way I have not had a problem even in heavy tool drawers, supporting much more than I should jam into some of these drawers. I will be building my own table saw station for my workshop rebuilding.
I made my drawers with pocket holes at the back and front of the drawers, that way the drawer front will hide the front pocket holes and no one will see the back pocket holes. Also makes the sides look clean.
Thanks for the tip. I realised that after the build ;-) and will do it like this next time.
Hi Andreas, pocket holes and glue is ok since is on sliders, that takes out some stress compared to drawers that rest or have direct contact with wood that add friction to the weight.
Thanks for your feedback.
ich bin kein Fan von Pocketholes...trotzdem klasse, daß du deine LESSONLEARNT zeigst
Danke für Dein Feedback, Thilo.
Have you considered partially enclosing your GTS10XC to get better dust collection? - I have been experimenting with strips of foam at the various gaps to try to reduce the dust that escapes the vacuum, which works reasonably well but nowhere near perfect.
So far I haven't but I’m planning on working on the dust collection situation (among other things: attach a second hose on the sawblade hood).
why not to use confirmator screws? Strong and tidy? ;)
Do you use a combination saw on the gts 10 xc ?
which one?
I replied to your first comment already.
Hallo Andreas, klasse Video. Gute Tipps. Vielleicht könnte man noch mehr darauf eingehen, wie man die Schubladen baut und EINBAUT. Wie breit sollte die Lade sein relativ zur Breite des Korpus? Sollte man zuerst die Laufschienen montieren und dann die Lade entsprechend der verbleibenden Breite bauen? Ich weiss, dass die Vielfalt der verfügbaren Auszüge das Thema sehr komplex machen könnte, aber es gibt nach meiner kurzen Erfahrung noch viel zu sagen... Vielleicht ein zusätzliches Video? Nach meiner Erfahrung sitzen die Pocketholes so bombenfest, dass man hier nichts befürchten muss. Auch ein guter Hinweis zur Staubbildung und wie man es vermeidet, dass der Staub in die Schublade gelangt! Weiter so! Vielen dank, dij-w-a
Zu verschiedenen Auszügen plane ich schon ein Video, das in den nächsten Wochen kommt.
So how did the drawers hold up? Any issues over time?
They're holding up well - no issues so far.
👍🥃🏴
Hi Andreas! Was hast du für ein Holzöl genommen? Die Schubladen sind super geworden, ich hoffe, mir bald selbst einen kreissägen Unterschrank zu bauen. Weiter so!
Danke, das war in diesem Fall ganz normaler Leinölfirnis.
Ja, staubdichte Schubladen.... ein altes bis heute nicht wirklich gelöstes Thema. Zumindest im DIY-Bereich. Und ja, ich hatte mich gleich bei den ersten Aufnahmen mit den Taschenlöchern gewundert, warum an der Seite? Da sieht man die doch. Aber, dachte ich, sind ja Werkstattschubladen. Kommt nicht drauf an. An die Winkelbelastung ist aber sicher zu denken. Da hast du sicher recht.
Aber die Schubladen fügen sich gut in den Schrank, wie wenn sie schon immer da gewesen wären.
Tja, Alfred. Leider ist mir das mit den sichtbaren Taschenlöchern auch erst später aufgefallen ;-) Aber deswegen mache ich neue Dinge gern zuerst für die Werkstatt, da ist es nicht tragisch, wenn man durch die Fehler lernen muss. Danke und beste Grüße, Andreas
Very nice project, as usual the “what I learned” is always helpful.
Thanks Richard.
hallo nochmal Andreas... die Griffe der Schubladen ein bisschen tiefer angebracht und kein Staub fällt mehr in die Schublade hinein... Grüße ins Markgräfler Land Thilo
Ja, das hast Du Recht. Wäre eine simple Lösung gewesen ;-)
Hey, just a friendly reminder in English its spelled learned.
Thanks for your feedback, in British English (and other British-based variants around the world) it’s actually learnt: en.wiktionary.org/wiki/learnt#English
Found an even better explanation: www.grammarly.com/blog/learned-learnt/
Tolles Projekt und wie immer alles super erklärt. Nun muss ich in den Keller und meinen Kreissägenunterschrank überdenken...
Danke fürs Zeigen