Thanks for the straight forward insight🤜🏻replaced my pivot with a stainless unit, cannot recall where I got it I’ve been putting it off for so long🤣 Got tired of the duct tape residue
I appreciate you, hoss! My f150 gas door was a little loosey goosey... I was wondering how to fix it... now I know! Gonna get at her in the next day or two after I knock out some other projects I got going on.
Gonna do this today or tomorrow, I’ve watched 6 videos and so far you’re the only one showing how to drill it instead of saying “just drill it here and do this” after the fact, great video
I've seen two other repairs that drill a hole down into the plastic dowel and then put a small screw with a washer in that hole. I think your fix is a better one, thanks for sharing!
eBay has a metal kit for the henge pin for 7, and an assembly for 14. This should fix it. If I have to redo anything the second time, it's get modified! I damaged my door , had to get another. Good video!
You can also get the fuel dog of from the outside with a flat head screw driver. Just set something between it and the paint like a piece of cardboard. Easily peel bsck the thin rubber with a pic or something and get your screwdriver in there a pry it out. Just a tip, some guys got big forearms.
You made this look so easy. I have been told it was an expensive job. I think I'm going to have to watch this video about 5 or 6 times before I get the nerve to try to do it. I hope I can. Thanks for the video.
I have done it at least 4 times now. I encourage you to give it a try. There really isn't much you can do wrong. The trickiest part is getting those little plastic tabs pressed just enough to pop the unit out but it is absolutely doable.
Made this same repair on my 2018 twice so far. Did it from underneath laying on my back. A little tough to reach but easier than removing the housing. Will happen again since I couldn’t drill it.
excellent work, great video. thank you for sharing. You earned yourself a new subscription, and I turned the bell notification on for your channel. thank you Brian.
Yes try to replace the latch assy for the center folding seat assy. $650 for the whole center seat assembly! $19.99 for the replacement from Bone wells!
Thanks for the straight forward insight🤜🏻replaced my pivot with a stainless unit, cannot recall where I got it I’ve been putting it off for so long🤣
Got tired of the duct tape residue
I appreciate you, hoss! My f150 gas door was a little loosey goosey... I was wondering how to fix it... now I know! Gonna get at her in the next day or two after I knock out some other projects I got going on.
My dads truck just did this last week, so this morning after watching your video, I was able to fix it.
Thank goodness for RUclips mechanics.
Gonna do this today or tomorrow, I’ve watched 6 videos and so far you’re the only one showing how to drill it instead of saying “just drill it here and do this” after the fact, great video
I've seen two other repairs that drill a hole down into the plastic dowel and then put a small screw with a washer in that hole. I think your fix is a better one, thanks for sharing!
Either way be fine.
My 09 is doing this AGAIN, going to try this Saturday!
eBay has a metal kit for the henge pin for 7, and an assembly for 14. This should fix it. If I have to redo anything the second time, it's get modified! I damaged my door , had to get another. Good video!
Just finished it! Beauty of a fix. Thanks.
Great video, found the same issue on my F150. I didn't have a cotter pin so I drilled the hole as described and used a paperclip! Worked perfectly!
Great fix. Just did this today. Easy to do. Thanks for the idea.
You can also get the fuel dog of from the outside with a flat head screw driver. Just set something between it and the paint like a piece of cardboard. Easily peel bsck the thin rubber with a pic or something and get your screwdriver in there a pry it out. Just a tip, some guys got big forearms.
You made this look so easy. I have been told it was an expensive job. I think I'm going to have to watch this video about 5 or 6 times before I get the nerve to try to do it. I hope I can. Thanks for the video.
I have done it at least 4 times now. I encourage you to give it a try. There really isn't much you can do wrong. The trickiest part is getting those little plastic tabs pressed just enough to pop the unit out but it is absolutely doable.
Made this same repair on my 2018 twice so far. Did it from underneath laying on my back. A little tough to reach but easier than removing the housing. Will happen again since I couldn’t drill it.
Worked as described but I could not get my arm in far enough to get to the top bracket so I had to remove the brace from the truck bed.
Thanks for that. I'll he fixing mine tomorrow.
I wish that was exactly like my 2013 Ford Taurus but it's not.Can't fix mine that way at all
excellent work, great video. thank you for sharing. You earned yourself a new subscription, and I turned the bell notification on for your channel. thank you Brian.
You can pop clips at fuel door opening you don’t have to reach around under bed also for 28$ you can just buy new complete latch from eBay
Awesome video
Great video..thanks
Thanks was very helpful
Some how I think Ford designed that door assembly to be replaced, not repaired
That is fairly accurate for almost everything on vehicles these days.
Yes try to replace the latch assy for the center folding seat assy. $650 for the whole center seat assembly! $19.99 for the replacement from Bone wells!
Ryan