Thank you very much for your tutorial, complete, on this complex subject, but you made it simpler, uncomplicated!! Following your tutorial, I will be able to finish the pending issues to run the Pi Node. Thank you again!
@@CryptoJar hi I have problem Unable to reach the network, please provide the IP/domain of a known node ...Pi Node Error Fix , I up v4.29.0 already how to fix please help thanks you so much
4:43 Hello sir .. I'm using a Router Tenda F9 and I did try to use chatGPT for assistance but still can't get it right I need help setting up my PORT FORWARDING . I have AnyDesk too if you'll be able to assist .
Hello, thank you for the video. I want to use my MacBook Air M2 as a node over wi-fi. Unfortunately I still can’t setup the port forwarding on my Zyxel VMG3625-T50B. When I go to the port forwarding option located under Network Setting / NAT in the menu, I see a couple of drop down options - WAN Interface (Default, WWAN, ADSL, VDSL, ETHWAN, VDSL Mngmt and ETH Mngmt) and Protocol which I’ve set to TCP/UDP. Start/End Ports are set to 31400-31409 as required by Pi. Translation Start/End Ports are set automatically the same. Next, I only see Server IP Address, optionally Configure Originating IP… Eventually, no matter what I do, I can’t run the node because I am unable to setup the port forwarding… Can you please advise me what am I doing wrong? Thank you so much! 🙏🏻
On the WAN ports, some routers may ask for a range eg .1-65535 Issue is if there is existing(another) port forward rule, this gets overlapped and interface does not allow to proceed. UPDATE:WAN port range is also 31400 to 31409(same as LAN port range)
I have a genesis gx router - titanium 2122A. It says External port, Internal port and Internal Server. What needs to be added in which field? Also it does not let me add range in the ports field. Ports field only takes 5 digits
@@nagbintu did you manage to make it work? i use router that uses a sim card to have an internet and still not working even after setting up the virtual server on the nat forwarding the port says it is still close
@@CryptoJar I have now 3 ports open, but something is still wrong. When I press 'Check now' button, the Ports listener is not downloading; like it tries and immediately stops. Any idea how to resolve it? Another question, I have a Pi-consensus container, not the Stellar-dummy; is it a problem? I just can not find the Stellar-dummy in Dockers...
Question this feature is only available on the mobile Spectrum app for me in the Wi-Fi advance settings section meaning I think this only helps people using the Wi-Fi feature along with port forwarding and putting in TCP/UDP ports also enabling Upnp into it. How am I supposed to adjust those settings without being able to access the Lan router and adjust those settings since my connection is wired into the router itself just to play Warzone? I get 500mbps down and 24 mpbs up with a gaming beast there's no way in hell that lag or high latency or variations and packet bursts along with extrapolation because the client and server are out of sync, so the game says when I play Warzone it alerts me that this is happening. And I got Spectrum telling me there in the green which is complete bs. Everything has been updated I even bought CAT 6 cords not the cheap kind that Spectrum supplies and still nothing. Hopefully they figure it out this week with my appointment because I'm going to pull my hair out.
I also had to port forward on my McAfee Anti Virus to fully open the ports. It’s a bit tricky to figure out, but you will have to play around with the settings.
you can use most computers that meet the below requirements Windows 10/11 64-bit processor with Second Level Address Translation (SLAT) 4GB system RAM BIOS-level hardware virtualization support
can you advise how to get Pi Notes opened if you don''t have access to the Router. Just open ports that are required to run Pi Node. ( i did had my Pi Node running without doing anything with the router comfig , problem for me is i have to reFormat my Hard Disk, now i forgot how i did it years ago )
I have an Aircube ISP in router mode and in the port forwarding section, I see SRC. PORT and DST. PORT. I googled them and found out that they are Source Port and Destination Port. I'm not sure what I should put in each section. Do you have any suggestions? Also, it seems that I am not able to add a range of ports, so I guess I will have to add each port manually.
SOURCE is going to be the IP of you computer. If you want to put in a range try 31400-3109 or just put them in separately. that may work, i havent used that brand of router.
Thank you very much but I need more help. The router port forward is ok. Tested with port checker. Windows port forward is ok. Tested with netstat command. But PI Node app says always "We couldn't reach the required ports on your machine. Please double-check your configuration." And in Docker the image ports links to localhost:3140[0-9]. I use wamp for web develop. Maybe this causes the problem? How can I solve this? Thanks in advance!
hi there, buddy, can this all be done on a mobile/cell phone device? atm i'm having no luck, everything i try is failing. bit of help with my first question would point me in the right direction
Sorry I should have mentioned, that Im using a PC to do this, only the WiFi hotspot from the cellular phone as a router.I hope hour answer is the same.
Hi ! Im on Fritzbox, and when i attempt to add a new sharing port, they first ask me the device, the ipv4 adress and the ipv6 interface id, then only after this step, they allow me to add a "new sharing", when i set up the new sharing it ask me the same info that when you create a new port on unfi. Problem, i can't use my ip node adress because its says me that its already taken, what should i do ? Thank you Edit : i solve the problem, but a new appeared : can't open the port, even if the "PiNodePort" configurated is on green light in my fritzbox, the ip adress seems different on the node port maybe its that, but i can't change it
I have spent 2 hrs trying to figure out what my external and interal ports are. after watching this video 3x and researching articles I still can not figure out what they are. I see the port # on PI what ports are those? in my wifi network app on the advanced settings it has only one option which is to reserve the IP address in port forwarding. when I select my device it ask for the external and internal for #s 1 through 65535. yet nothing is giving me a clear statment even after using the netstat in cmd just a bunch ips. HELP?!
Hii:) Any Idea on how to do portforwarding on Vodaphone router ? I followed your steps, but Vodaphone interface is bit changed then what you has for your connection, from me it asks device name which is in the connected list devices, when I chose my Device name it picks up the IP address it self, but it names it MAC address. but still it does not work all the ports are still closed.
Hi. The stellar-dummy is running from few days now but my porte are still not open. I opened them in the router and the firewall. Any advice please. I am trying this from day. Thank you
Hi. Thanks for your easy to follow tutorial I have one question, though. My router is asking for a server port, it won't let me save the info if I don't enter one. I read that Server Port 1 is used for TCP/UDP, is this information correct or should I put in a different port number? Thank you.
@@CryptoJar Thanks for the reply. I entered 31400-31409 but says it's invalid. Additional question, if I may, on the server IP Address entry, do I enter my default gateway IP (same IP to login to my router)?
Hi, i am connected directly to my ISP router. and it does not give me any port forwarding option. does that mean i need to set up a separate router with the port forwarding feature?
What if my only options in the port forwarding section was: Common protocol and port (optional), Internal Port num, external port num, and protocol? Im using nova router
i think this guide might be best to follow for the port forwarding www.microcenter.com/tech_center/article/8323/how-to-forward-or-open-a-port-on-a-tenda-router
Hello @cryptojar hope this comment may reach you. Just want to ask Im using windows 10, and a huawei router? does that means I will not be able to use Pi node in my computer? Thanks in advance take care always 🙏🙏🙏
I set this up with my Fritzbox router and also added in Windows firewall, but still not getting ang od these ports to open. Not sure in this is anything to do with but my IP in msinfo and in the port checker pi page are completely different.
@nieczerwony I am facing the same issue as well, my IP address is static but once I check on port checking website I get different IP address which might be my sim card address. The ports are still closed. Are you able to resolve yours?
Hi guys, need some help.. I've downloaded NODE but it still doesn't work (even tho I got DOCKER installed too) I when I open NODE (I get the message: "PI NODE APPLICATION SUBMITTED") and hit continue button it's just spinning for hours but nothing happens.. Any idea how I could check what ports are open on my WiFi router?
New sub thanks for the vids. Have you heard anything about Docker causing the Pi Node to get stuck saying "Please wait.... Loading may take up to one minute.
Yes that actually happened to me. I had to reboot my computer and completely kill docker. Then restart everything and make sure the container for Pi is running.
@@CryptoJar oh.. iam following up to run a node since last year, i set up everything running perfectly but I don't have any modem or router iam 100% using telecome network mobile is there any adjustment that u can help me so that the network can connect to blockchain....?
Hey Brother, Thank you for Helping with these videos. I have an Arris Modem, and the port forwarding is not allowing me to move to the next step. Could you help me with this issue if you ever get a chance. Thank You
Im trying for 4days to open ports on ZTE H267N v1.1 I know login info,I set thru network operator statick IP and I set like you(I think so) but nothing hapens. if you can help i can send pictures of device ip and everything what you need
I opened all of the ports correctly and it shows so on the test port website. However, the "starting ports listener" is always loading and won't pass on to "Pinging your computer". Is there any way to solve this problem?
i cant even get to the page with the 3 checking steps. The Pi Node always jumps directly to the Node screen with the pink switch. Also my local block numer is always "1" and doesnt move... On my laptop everything works fine even without port forwarding... Maybe my pc system is just shitty after all
Hi, thank you for this very useful and informative video. I was able to set up the node with minimal issues. I am doing this for the first time, so I am a bit concerned about security due to port forwarding. I have several devices connected to my router at home. Do you have any advise for me?
There's no monetary value yet, but when you run a node, you're mining at a higher rate. At some point this should equal some kind of dollar amount, and that's if you believe this network will grow into something. Since the network has millions of active users, i think it has a decent chance.
I am using tp link Archer c6. I did the port opening from the firewall and router but after follow all the procedure it's showing that Port are closed. very complicated 😢
Thanks for this video bro I gain general idea about port forwarding however I'm still having a hard time how to properly enable port forwarding on my Skyworth router it seems that it's not working for me even though I tried to follow all the steps, all though our router setting is quite different which I understand, hope you could help me brother.
you are awsome bro. Its all new for me. Your videos helped me a lot. but i am stuck at Port Forwarding. I have TP link archer c60 router. I have followed all the steps but node is still not opening. what could be the reason? Is static IP is necessary for setting port forwarding??
thanks! static ip is not necessary, but helps. When you restart your computer there is a chance your ip address will change. I havent used any TP link routers, but if its provided by your ISP, i would check with them to confirm the settings.
Hi bro thanks. Everything ok but 31400-31409 always not opened. And I checked cmd also these are not listed. Do you have any ideas? I'm using TIMlink in Italy.
@@CryptoGoldB ah okay, if it's wireless then it may not be using a public IP on your modem. If that's the case you may not be able to set this up. You should chat with them and confirm
@@CryptoJar Hi Bro , I did call to ISP to open port 31400-31409 and they're done and charged. But still not an open problem while pinging my computer. But I skipped and continued to turn on the node , it's running ...but inside docker exited 31400-31409 instead of running another container pi consensus 31403:1579, 31402:31402, 31401:8000. Is it ok ? Also open router ports are not in green tick.
Resolved... Seems at some point my modem switched itself back to router mode without me knowing.... Resetting it to Modem Mode Cleared the Ports Pi Node is up and running:) This video helped A Lot. Thanks I'm having issues with the Ports Not Opening... I have configured the Port Forwarding in my Router (Netgear Nighthawk R7000) But when I run the check in the Pi Node App the Ports are all CLOSED I have restarted both my Router and Pc (Windows 10) several times with no luck. I am running Norton Security Firewall, but no idea if that is the problem as I get no alerts or warning popups as I do when norton blocks an intrusion. My Router is connected to Internet via Cable Modem configured in Modem Mode (Internal Router Disabled) I have no clue where the issue lies or how to fix it. Any Help Appreciated Thanks
Thank you very much for your tutorial, complete, on this complex subject, but you made it simpler, uncomplicated!!
Following your tutorial, I will be able to finish the pending issues to run the Pi Node.
Thank you again!
FANTASTIC! I am so happy you found it useful!
teach me how..im using window 11
@@CryptoJar hi I have problem Unable to reach the network, please provide the IP/domain of a known node ...Pi Node Error Fix , I up v4.29.0 already how to fix please help thanks you so much
you started with MacBook but end up using windows 10 in command prompt? I can’t follow up like that beside that am using MacBook Pro 😅😅
4:43 Hello sir .. I'm using a Router Tenda F9 and I did try to use chatGPT for assistance but still can't get it right I need help setting up my PORT FORWARDING . I have AnyDesk too if you'll be able to assist .
Hello, thank you for the video. I want to use my MacBook Air M2 as a node over wi-fi. Unfortunately I still can’t setup the port forwarding on my Zyxel VMG3625-T50B. When I go to the port forwarding option located under Network Setting / NAT in the menu, I see a couple of drop down options - WAN Interface (Default, WWAN, ADSL, VDSL, ETHWAN, VDSL Mngmt and ETH Mngmt) and Protocol which I’ve set to TCP/UDP. Start/End Ports are set to 31400-31409 as required by Pi. Translation Start/End Ports are set automatically the same. Next, I only see Server IP Address, optionally Configure Originating IP… Eventually, no matter what I do, I can’t run the node because I am unable to setup the port forwarding…
Can you please advise me what am I doing wrong? Thank you so much! 🙏🏻
On the WAN ports, some routers may ask for a range eg .1-65535
Issue is if there is existing(another) port forward rule, this gets overlapped and interface
does not allow to proceed.
UPDATE:WAN port range is also 31400 to 31409(same as LAN port range)
It would help if you would show how to bind MAC address to IP address so that the node gets same private IP each time pc shuts down/restarts.
Good to see you helping people sort things out, always keep the good work up 👍❤️
I have a genesis gx router - titanium 2122A. It says External port, Internal port and Internal Server. What needs to be added in which field? Also it does not let me add range in the ports field. Ports field only takes 5 digits
can u do a guide for tp-link updates user interface because i dont understand which field to fill with which information :(
its virtual server for tp link find it under advanced options
@@nagbintu did you manage to make it work? i use router that uses a sim card to have an internet and still not working even after setting up the virtual server on the nat forwarding the port says it is still close
@@AniiiClips it won't work for me we would need to buy a static IP from the isp
Oh man, thank you, I finally managed to open the ports following your tutorial!
Glad I could help!
@@CryptoJar I have now 3 ports open, but something is still wrong. When I press 'Check now' button, the Ports listener is not downloading; like it tries and immediately stops. Any idea how to resolve it? Another question, I have a Pi-consensus container, not the Stellar-dummy; is it a problem? I just can not find the Stellar-dummy in Dockers...
What is the effect of docker and pi node on the performance of the pc?Is there any lag when these softwares are installed?
Docker is required to run the node and does have a performance requirement. You will probably notice more with the use of RAM
I did all the steps. I also allowed the relevant connection in the firewall. but it says your port is closed.
Question this feature is only available on the mobile Spectrum app for me in the Wi-Fi advance settings section meaning I think this only helps people using the Wi-Fi feature along with port forwarding and putting in TCP/UDP ports also enabling Upnp into it. How am I supposed to adjust those settings without being able to access the Lan router and adjust those settings since my connection is wired into the router itself just to play Warzone? I get 500mbps down and 24 mpbs up with a gaming beast there's no way in hell that lag or high latency or variations and packet bursts along with extrapolation because the client and server are out of sync, so the game says when I play Warzone it alerts me that this is happening. And I got Spectrum telling me there in the green which is complete bs. Everything has been updated I even bought CAT 6 cords not the cheap kind that Spectrum supplies and still nothing. Hopefully they figure it out this week with my appointment because I'm going to pull my hair out.
It is impossible to do it on tp-link router.
Are you serious?
@@Skullislandfoundyou Yes
@@Gaga682try ngrok to open multiple ports (use 6 different accounts for 6 ports because the free account only allowes one port at a time)
Can i do it using wifi providers and without router? Plz reply
Yup it’s correct
I also had to port forward on my McAfee Anti Virus to fully open the ports. It’s a bit tricky to figure out, but you will have to play around with the settings.
Yes, thanks for pointing that out. This video is to give a general idea of how to port forward but it really depends on your setup
Can you suggest a spec of a computer or laptop? Or what is the system requirement to setup a node and super node?
you can use most computers that meet the below requirements
Windows 10/11
64-bit processor with Second Level Address Translation (SLAT)
4GB system RAM
BIOS-level hardware virtualization support
can you advise how to get Pi Notes opened if you don''t have access to the Router.
Just open ports that are required to run Pi Node.
( i did had my Pi Node running without doing anything with the router comfig , problem for me is i have to reFormat my Hard Disk, now i forgot how i did it years ago )
Thank you for all informations please i have a problem with tp link about
External port & internal port
what should i do on ??
I have an Aircube ISP in router mode and in the port forwarding section, I see SRC. PORT and DST. PORT. I googled them and found out that they are Source Port and Destination Port.
I'm not sure what I should put in each section. Do you have any suggestions?
Also, it seems that I am not able to add a range of ports, so I guess I will have to add each port manually.
SOURCE is going to be the IP of you computer. If you want to put in a range try 31400-3109 or just put them in separately. that may work, i havent used that brand of router.
How can I use port forwarding to Tenda AC6 model? Is it possible for this router?
how to port forward using Huawei EG8145V5?
I have no idea
Thank you very much but I need more help. The router port forward is ok. Tested with port checker. Windows port forward is ok. Tested with netstat command. But PI Node app says always "We couldn't reach the required ports on your machine. Please double-check your configuration." And in Docker the image ports links to localhost:3140[0-9]. I use wamp for web develop. Maybe this causes the problem? How can I solve this? Thanks in advance!
hi there, buddy, can this all be done on a mobile/cell phone device? atm i'm having no luck, everything i try is failing. bit of help with my first question would point me in the right direction
It depends if you are getting an external IP which can have the ports forwarded. If it's on a cellular network I'm not sure how or if it works
Sorry I should have mentioned, that Im using a PC to do this, only the WiFi hotspot from the cellular phone as a router.I hope hour answer is the same.
Shenzhen Tozed model ZLT S 10 router unable to port forwarding can you please how to do it from it
Hi ! Im on Fritzbox, and when i attempt to add a new sharing port, they first ask me the device, the ipv4 adress and the ipv6 interface id, then only after this step, they allow me to add a "new sharing", when i set up the new sharing it ask me the same info that when you create a new port on unfi.
Problem, i can't use my ip node adress because its says me that its already taken, what should i do ?
Thank you
Edit : i solve the problem, but a new appeared : can't open the port, even if the "PiNodePort" configurated is on green light in my fritzbox, the ip adress seems different on the node port maybe its that, but i can't change it
I have spent 2 hrs trying to figure out what my external and interal ports are. after watching this video 3x and researching articles I still can not figure out what they are. I see the port # on PI what ports are those? in my wifi network app on the advanced settings it has only one option which is to reserve the IP address in port forwarding. when I select my device it ask for the external and internal for #s 1 through 65535. yet nothing is giving me a clear statment even after using the netstat in cmd just a bunch ips. HELP?!
Hii:) Any Idea on how to do portforwarding on Vodaphone router ? I followed your steps, but Vodaphone interface is bit changed then what you has for your connection, from me it asks device name which is in the connected list devices, when I chose my Device name it picks up the IP address it self, but it names it MAC address. but still it does not work all the ports are still closed.
Thanks a lot. It was so clear and useful. 😊
in my own router's site. It says wan host ip address, lan host, wan port, lan host port. Where are the forward port options?
thank you Sir for your tutorials. please how do I get a static ip address to enable me run pi node on my computer.
Type ipconfig on your CMD
im having trouble because im asked to type a lan port. where do i find the lan port?
when running in pi node, will it increase the mining rate or just the same?
Hi. The stellar-dummy is running from few days now but my porte are still not open. I opened them in the router and the firewall. Any advice please.
I am trying this from day.
Thank you
when you run the port test, does all of them pass?
@@CryptoJar How to do the potr test?
@@CryptoJar They are all not open, the last step pinging your computer is saying to check computer configuration
@@marianmanea1691 pi-mods.de/nodeports/
@@marianmanea1691 the first 3 ports are the only ones currently being used
Hi. Thanks for your easy to follow tutorial I have one question, though. My router is asking for a server port, it won't let me save the info if I don't enter one. I read that Server Port 1 is used for TCP/UDP, is this information correct or should I put in a different port number? Thank you.
yes thats correct, the server port should be the same numbers
@@CryptoJar Thanks for the reply. I entered 31400-31409 but says it's invalid.
Additional question, if I may, on the server IP Address entry, do I enter my default gateway IP (same IP to login to my router)?
@@teleponokoni713 the server IP will be the IP of the computer you're using.
Do you have to have static IP address for port forwarding to work
Nice video, does port forwarding required to run the block chain? Or block chain can be run without port forwarding
i believe its required.
@@CryptoJar thanks for your reply, are you receiving node bonus?
Hi, i am connected directly to my ISP router. and it does not give me any port forwarding option. does that mean i need to set up a separate router with the port forwarding feature?
It's best to contact your ISP and ask how forwarding works
What if my only options in the port forwarding section was: Common protocol and port (optional), Internal Port num, external port num, and protocol? Im using nova router
I got t mobile router but I had used localxpose to go around my router to make a port forwarding. But I did eventing it still nothing open
Can you list down tested router brands and modem to be use for pi node. Thank you! Awesome video.
Thanks for the idea! i'll add some stuff to the blog
Bro i have tenda router how do i fill these
Internal IP
External Port
External Port
i think this guide might be best to follow for the port forwarding www.microcenter.com/tech_center/article/8323/how-to-forward-or-open-a-port-on-a-tenda-router
@@CryptoJar thank man🌝
@@badbat4649 np
Hello @cryptojar hope this comment may reach you. Just want to ask Im using windows 10, and a huawei router? does that means I will not be able to use Pi node in my computer? Thanks in advance take care always 🙏🙏🙏
Hello, if your router is able to get a public IP and forwarding to your PC works, then it should be okay.
I set this up with my Fritzbox router and also added in Windows firewall, but still not getting ang od these ports to open.
Not sure in this is anything to do with but my IP in msinfo and in the port checker pi page are completely different.
@nieczerwony I am facing the same issue as well, my IP address is static but once I check on port checking website I get different IP address which might be my sim card address. The ports are still closed.
Are you able to resolve yours?
Sir please answer my question, is it necessary to have static IP to run Pi node .
Hi guys,
need some help..
I've downloaded NODE but it still doesn't work (even tho I got DOCKER installed too) I when I open NODE (I get the message: "PI NODE APPLICATION SUBMITTED") and hit continue button it's just spinning for hours but nothing happens..
Any idea how I could check what ports are open on my WiFi router?
my kabel-modem have no option for portforwarding..... i found only IPv6 Host Exposure. i need some help!!!
Please help me setup port forwarding in Huawei router
Thank you so much for your help
You are most welcome
New sub thanks for the vids. Have you heard anything about Docker causing the Pi Node to get stuck saying "Please wait.... Loading may take up to one minute.
Yes that actually happened to me. I had to reboot my computer and completely kill docker. Then restart everything and make sure the container for Pi is running.
@@CryptoJar Thanks Bro...
I have no idea what you mean by Switch over the router 1:24
That's poorly worded. I meant I'm using another PC to connect to my router and make changes
hi cryptojar, can someone run a node with mobile service providers internet network??
i think its possible, but i would consider the amount of data that could be used. It may not be a good idea
@@CryptoJar oh.. iam following up to run a node since last year, i set up everything running perfectly but I don't have any modem or router iam 100% using telecome network mobile is there any adjustment that u can help me so that the network can connect to blockchain....?
@@CryptoJar ..make a tutorial using with mobile service providers internet
is this only for wired connections? Just bought an ASUS TUF AX6000 and i still cant figure it out with my Macboom pro 😢
As long as your computer has a static IP, it shouldn't matter if it is wired or wireless
Hey Brother, Thank you for Helping with these videos. I have an Arris Modem, and the port forwarding is not allowing me to move to the next step. Could you help me with this issue if you ever get a chance. Thank You
i am not too familar with Arris Modems, do you have static ips set?
Im trying for 4days to open ports on ZTE H267N v1.1 I know login info,I set thru network operator statick IP and I set like you(I think so) but nothing hapens. if you can help i can send pictures of device ip and everything what you need
Please help me i open all ports but only starting ports listener didnt appearl, what should i do.
I opened all of the ports correctly and it shows so on the test port website. However, the "starting ports listener" is always loading and won't pass on to "Pinging your computer". Is there any way to solve this problem?
are you able to confirm that docker is running?
I was already a node, today when I entered the computer I had the same problem
amazing how no one can explain the solution
i cant even get to the page with the 3 checking steps. The Pi Node always jumps directly to the Node screen with the pink switch. Also my local block numer is always "1" and doesnt move... On my laptop everything works fine even without port forwarding... Maybe my pc system is just shitty after all
Thanks alot! you really helped me.
Hi, thank you for this very useful and informative video. I was able to set up the node with minimal issues. I am doing this for the first time, so I am a bit concerned about security due to port forwarding. I have several devices connected to my router at home. Do you have any advise for me?
I think as long as you are only opening ports and forwarding it to the one PC you should be fine with minimal risk.
@@CryptoJar Thanks! That was definitely reassuring. Appreciate you taking the time to reply to all comments received for your video.👍
I have done the port forwarding and its not redirecting to the laptop.
I am facing issue with the virtual port not sure what is the number
i cant do this port forwarding on a pldt internet provider please can you make a vid for a default service provider modem
There are so many brands and models it's hard to make a video being specific because it will be different for each user based on their ISP
What are the benefits/rewards for setting up/running a pi node?
There's no monetary value yet, but when you run a node, you're mining at a higher rate. At some point this should equal some kind of dollar amount, and that's if you believe this network will grow into something. Since the network has millions of active users, i think it has a decent chance.
I am using tp link Archer c6. I did the port opening from the firewall and router but after follow all the procedure it's showing that Port are closed. very complicated 😢
How abot eir router, can you please show how to do it?
Thanks for this video bro I gain general idea about port forwarding however I'm still having a hard time how to properly enable port forwarding on my Skyworth router it seems that it's not working for me even though I tried to follow all the steps, all though our router setting is quite different which I understand, hope you could help me brother.
Bro my router only has port mapping and port trigger can these be used?
Yeah that's should be the same
you are awsome bro. Its all new for me. Your videos helped me a lot. but i am stuck at Port Forwarding. I have TP link archer c60 router. I have followed all the steps but node is still not opening. what could be the reason? Is static IP is necessary for setting port forwarding??
thanks! static ip is not necessary, but helps. When you restart your computer there is a chance your ip address will change. I havent used any TP link routers, but if its provided by your ISP, i would check with them to confirm the settings.
Hi bro thanks. Everything ok but 31400-31409 always not opened. And I checked cmd also these are not listed. Do you have any ideas? I'm using TIMlink in Italy.
Hey bro, thanks! I dont know what kind of hardware TIMlink uses. Is this a DSL/cable service, or wireless ?
@@CryptoJar thanks for your response. It's a wireless modem TIM HUB. Maybe I need to call them to open a port. I don't know! .
@@CryptoGoldB ah okay, if it's wireless then it may not be using a public IP on your modem. If that's the case you may not be able to set this up. You should chat with them and confirm
@@CryptoJar Hi Bro , I did call to ISP to open port 31400-31409 and they're done and charged. But still not an open problem while pinging my computer. But I skipped and continued to turn on the node , it's running ...but inside docker exited 31400-31409 instead of running another container pi consensus 31403:1579, 31402:31402, 31401:8000. Is it ok ? Also open router ports are not in green tick.
i portforwarded and your website still shows closed dfor me, but it also shows up a different IP when going to your website than it does in my cmd
Thats normal, the ip in your browser is your public ip, its the same for your whole network, the one in the terminal is your local private ip
hi what if someone uses mobile hotspot ?
Did you get any solution
Please help me
is it possible to forward ports without having static ip?
Thank you very much !!!
Glad it helped
Resolved...
Seems at some point my modem switched itself back to router mode without me knowing.... Resetting it to Modem Mode Cleared the Ports
Pi Node is up and running:)
This video helped A Lot. Thanks
I'm having issues with the Ports Not Opening...
I have configured the Port Forwarding in my Router (Netgear Nighthawk R7000) But when I run the check in the Pi Node App the Ports are all CLOSED
I have restarted both my Router and Pc (Windows 10) several times with no luck.
I am running Norton Security Firewall, but no idea if that is the problem as I get no alerts or warning popups as I do when norton blocks an intrusion.
My Router is connected to Internet via Cable Modem configured in Modem Mode (Internal Router Disabled)
I have no clue where the issue lies or how to fix it.
Any Help Appreciated Thanks
Are you able to run a Pi node on a racknerd VPS?
yes you could, but you wouldnt be earning anything... yet. I might do it when the token has value.
What if you are using a private network like from a mobile phone to hotspot your pc
I don't think that's going to work. You are going to need an external ip that can commit on the network
How do I locate the nope IP address
To find your IP, go to the command prompt and type in 'ipconfig'
how can i do on ptcl routor
i have tmobile gate way can you make a video how to do it with that ? pls :D
Unfortunately I don't have that device to demonstrate the configuration, sorry
Brother i am from india using Jio Fiber how to connect port in Pi, Please guide me 🙏 I am beginner
Hey bro, I don't know anything about Jio hardware, it's not available here 😐
Can u pl guide for Orbi router for opening ports
Sorry bro, I wish I could, I just don't have the hardware, there are so many different brands
Can I use pi node from phone hotspot?
ı am connecting from my university dorm wifi and i dont have acces to routers so does that mean i cant configure node at all ?
Unfortunately yes, it sounds like you won't be able to do it unless you are provided access
What would we use as the External Host ip?
i would leave that as all or blank
CAN I USE VPN FOR MY NODE? BECAUSE IF TURN ON MY VPN THE PORT SHOW CLOSED WHEN TEST. PLES SOME INFO
i am using android hotspot, what should i do
Sir please help me I couldn't setup pi node 🙏
how l do it wich digi?
Can I use a mifi, if I don’t have a router?
You can use anything as long as you have a public IP
How about only connect in wifi
i did all the above and its still showing that my ports are closed why ? any solution
Do you have a public IP?
How can i open with mobile hotspot
Thanks atas tutorial nya
node port belum terbuka dengan menggunakan router huawei HG8245H.
apakah bisa dibantu.
saya dari indonesia
hello ,what about Tenda router
you'll need to look up the exact settings for that model
hey i need you help
in adding nodes in jio link
I haven't used a Jio link before
Is there a solution please? I also always port only 31401-31403 can opened
ports 31401-31403 are currently the only ones being used, the others maybe used at a later time
@@CryptoJar as minhas também abre apenas 3 portas, mesmo não sendo todas estou contribuindo com apenas 3?
Can anyone help me with gnexis modem?
impossible to open ports 31400-31409 I have a starlink wi-fi router is the starlink the problem
ah man, i havent even seen on yet, but ya, i think that setup would be different when opening up ports
good night, please, can you help me?, I don´t can open the ports 😞thanks
i dont know how much help i can offer, but let me know the issue
Can i use my phone's hotspot to mine 👉👈?
It requires a public IP, I haven't tried that so I cannot confirm
There show any transition ?
what do you mean by transition?
it tells me the connection is not safe, so it is not smart to log in right?
which site is saying that?
I couldn't do it in tplink