Oof, preparing those nails, adding yellow bushings and gluing balls probably was a TREMENDOUS amount of work 😲 Still, thank you for this video, really inspiring and well-executed! 🌟👍
It's more of a simple concept than much of your other devices. But setting up all those nails look far more tedious than anything else you've done! You have the patience of a saint to do all of those! You have my eternal respect.
I don't know how this video appears here in eastern Europe, but thank you, it was a huge satisfaction. Female engineers are rare, and I have huge respect for that.
Pretty cool looking. I think I would have printed the yellow tubes with an internal wall a few mm from the ball bearing end. Make them easier to position the same height. I did something like that for holding dremmel tools. I printed a case from filament with threaded holes and then threaded inserts that held the shafts from tough resin with a little bit of spring grip.
If you design the nail-cutting jig to be taller, you wouldn't need to shim each one before cutting. You could make the uppermost section of each hole looser to make it easier to push in and pull out, too. You could even incorporate the final grid into this cutting jig to save you from taking them all out and reinserting.
I believe that beveling the sharp back edge of the windmill "blades" to a steep slope, would reduce the noise a bit. The pins would slide down that quickly, instead of slamming down from a small freefall.
Если между штырьками и подвижной платформой проложить рамку с эластичной и скользкой тканью типа капрона или фатина, на штырьки не будет приходить трение от вращающейся платформы, что снизит боковой перекос...
ziet er echt prachtig uit. Ben vooral onder de indruk van het gebruik van standaard onderdelen die iedereen wel kan kopen. geweldige video, ga vooral zo door 👍
It would be neat if the height of each nail could be determined by something like the rock paper scissors cellular automata, and see where the ball ends up going.
ENGLISH SPEAKERS: in the description, they said use subtitles! they have an english translation, dont just click off the video because you dont understand it! this seems like a very tedious project, so dont let them be confined to just a japanese audience! their content does look really cool and id probably be watching them a decent amount in my free time
凹みバージョンが1番不思議な動きに見えて好き
それな
11:40
True, from Spain
True, from Japan
恐ろしく地道な作業で尊敬しかない
Thank you for adding English subtitles! I love your work, and am happy that I can follow along better now 😁 Looking forward to your next project!
just read your comment as i finished the video with subtitles turned off
It looks like magic when it's the indentation plate, but the positive indent plate is mesmerizing. Very cool project, very well executed.
別バージョンのカムが出てきたときニッコリした
凹みバージョンは、ほかのバージョンと違い、何もないところを勝手にボールが進んでいるという、不思議な感じを楽しむことができるので、へこみバージョンが一番よかったです。
いつの間にかアイコンが変わっててびっくりした！
今回のも不思議とずっと見ていたくなるからくりだなぁ
偶に引っかかって元通り沈みきらない問題児の釘すき
な に こ れ ｗ
作業量がエグくて笑いましたわｗ
The things you come up with are always so fascinating. Love your work.
凹みバージョンが特に良かった。いつもながら良いですね
Oof, preparing those nails, adding yellow bushings and gluing balls probably was a TREMENDOUS amount of work 😲
Still, thank you for this video, really inspiring and well-executed! 🌟👍
発想、設計力すべてが天才過ぎる
Art meets engineering, I love it!!! It would also be really cool to reuse this idea for a clock.
It's more of a simple concept than much of your other devices. But setting up all those nails look far more tedious than anything else you've done! You have the patience of a saint to do all of those! You have my eternal respect.
動きが滑らかで気持ち良いですね
釘カットは最初から丁度良い長さの治具を作った方が良いような…
これが重力波ちゃんですか
作業量がエグい！お疲れさまでした✋⚡⚡
羽バージョンがASMRっぽさもあってずっと見てられる
The windmill version sounds good 👍
異常に多い単純作業で指怪我してるし…
すげえよ…
I absolutely love your videos! They're a great source of inspiration for my own making, and btw thank you much for including subtitles! :)
これ地面とか廊下に張り巡らすように設置して、立ってるだけで移動できるようになったら凄いよなぁ
CPUの裏側かな？😂
ピン折れ不可避で草
Socket478かな？
びっしり並んでるからAMDのAM2とかかもしれん
玉を転がさなくても波とか再現できると視覚効果で癒されそう
You are such a brilliant designer and fabricator. It as an absolute delight and pleasure to watch your work. Thank you so very much 🙏🏾
I don't know how this video appears here in eastern Europe, but thank you, it was a huge satisfaction. Female engineers are rare, and I have huge respect for that.
アイコンいつの間にか可愛くなってた
好き
11:10 マッサージチェアの腰あたりの挙動だ
ところで、これ工夫すれば歩行者用信号機出来るかも
ちょっとやってみる
これが置物としてあったらロマンしかない
それな！
いつにもまして地獄みたいな工程だ…
釘の作業が苦行すぎる……。すげえ。
''くぎ''の作業が苦行(''くぎ''ょう)すぎる…ねぇ
羽バージョン、気持ちよく動いてて好きだなあ
Beautiful. The reflection of the nails on the ball is neat!
I absolutely love this desktop toy! Great job! Love the design!!! You should sell these
左手人差し指の傷から大変な作業だったことがわかる
(っ´ω`c)はやくよくなれーッ
That looked so mesmerizing! The concave version looks the best with the marble, but without the marble, the two version is incredibly interesting
Pretty cool looking. I think I would have printed the yellow tubes with an internal wall a few mm from the ball bearing end. Make them easier to position the same height.
I did something like that for holding dremmel tools. I printed a case from filament with threaded holes and then threaded inserts that held the shafts from tough resin with a little bit of spring grip.
最後の羽バージョン時計みたいで好き
This is such a simple but smart design. Looks great! Keep it up!
Thank you for the English subtitles! That's a really cool project.
If you design the nail-cutting jig to be taller, you wouldn't need to shim each one before cutting. You could make the uppermost section of each hole looser to make it easier to push in and pull out, too. You could even incorporate the final grid into this cutting jig to save you from taking them all out and reinserting.
This looked very time consuming and beautiful. Good job!
Wow, that is fantastic, I could watch it all day! Great work!
ウルヴァリンの富豪の爺さんが寝てたベッド
this made me happy. thank you.
これは私を幸せにしました。 ありがとう。
（グーグル翻訳）
This is some fine engineering right here.
凹みバージョンの玉乗せる前、視えざるものが転がってる感じがして好き
今までの機構とは比べ物にならんくらい地道な作業で見てるだけのこっちが狂いそうになった
Omg the glueing step i cant. Id lose my mind.
That's insane! What a crazy amount of work for such a pretty effect.
looks great. my clumsy hand would never able to do half of those "nailing"
I believe that beveling the sharp back edge of the windmill "blades" to a steep slope, would reduce the noise a bit. The pins would slide down that quickly, instead of slamming down from a small freefall.
You have great patience and the end result was worth it. Amazing.
Если между штырьками и подвижной платформой проложить рамку с эластичной и скользкой тканью типа капрона или фатина, на штырьки не будет приходить трение от вращающейся платформы, что снизит боковой перекос...
Love the concave because it is impossible to perceive what is happening. :D
Someone has way too much time on their hands. So much work. Anyways, Well done!
この機構を上手く使って、玉を針に見立てた時計があったらめちゃくちゃカッコイイしインテリアになりそう😊
😮 I'm inspired by your work!
This is so cool, very mesmerizing to see built as well as see functioning! Excellent work!
羽バージョンの音が好き
Super cool! My favorite one is the concave version, it looks like the balls are moving by themselves
Thank you for the subtitles!!
The windmill is so trippy!
しゅ、修行かな…ってぐらい地獄の工程わらた
釘の戻り悪い所にシリコンスプレーか何か振りたくなるな…
imagine a nail wave machine the size of a room
Cool idea for a clock
一生見てられるやつ
if roads would be the same way, we could travel with stopped motors!
Interesting little desk toy, great work
なんかウルヴァリンの映画でこんな感じの介護ベット見たことあるな。
As always this is incredible. I was impressed with the time and efforts involved on the making of this one.
Windmill looks trippy
What program did you use to make this?! it looks incredible by the way!
なんと素晴らしい……
ziet er echt prachtig uit.
Ben vooral onder de indruk van het gebruik van standaard onderdelen die iedereen wel kan kopen.
geweldige video, ga vooral zo door
👍
Great idea! Love it!
売られたら買うわこんな凄いの
いつもながらおもろいものづくりされててワクワクします。質問です！3DCADソフトって何をお使いですか？独学ですか？
CADはRhinocerosを使っています。からくりの知識はほぼ独学ですがCADの基礎は大学で学びました。
アイコン変わっていいですね😊
今回のカラクリも面白いですね
It looks like Marble Madness for NES
今回もころがりすと！
釘の長さを整える道具があるんですね。
ES LO MAS LINDO QUE HE VISTO, DESEARIA TENER UNA IMPRESORA 3D, SALUDOS!!!
If you ever get one, just make sure it's self leveling. Trust me, it'll save you a lot of trouble.
a nice little machine :) just be careful not to get a repetitive strain injury
In awe at your talent
Looks like it could be made into a model of spacetime deformation. Exhibiting properties of how orbits work.
Incredible dedication
To me the concave is the best. You don't see how or what moves the ball.
Little Kiss from Spain.
Was für ein cooles Gerät! Du bist besonders fleißig. Dein Video war mega entspannend und unterhaltsam! Immer etwas Cooles!
This is so cool and creative!
What 3D modeling software was used for design?
Those perfectly manicured nails though
It would be neat if the height of each nail could be determined by something like the rock paper scissors cellular automata, and see where the ball ends up going.
Brilliant! Nice work!
見てるだけで指にマメができました
ENGLISH SPEAKERS:
in the description, they said use subtitles! they have an english translation, dont just click off the video because you dont understand it!
this seems like a very tedious project, so dont let them be confined to just a japanese audience! their content does look really cool and id probably be watching them a decent amount in my free time
Wow. This is wonderful.
" I made you a cool thing and am sending it to you free of charge "
Title fixed
I await the package 😃👍
凹凸をベルトコンベアみたいに回してその上を釘が波みたいにうねったら小さな海みたいになって船とか浮かべても面白そう
とてもかっこいい
Pretty ingenious!
Amazing work
まさしく「力作」でしたね！
速度調整用のつまみに、薄いワッシャーを挟めば、付かず離れずで良い距離感になると思います。
(左手の人差し指、大丈夫ですか？)