mine shows CS_906W_TX_3D_V1.3, I tried upgrading using your video link with SD CARD but unfortunately it doesn't boot up anymore, because when i was pressing reset with a pin, i flipped and i wanted to repeat the process from a fresh. but now i messed up kindly assist
I used this as a starting point to install atvxperience (AidanROM), but I bricked my TX3 Mini in the process. From there, I tried several different stock ROMs attempting to fix it, with no success. My board is blue and it says CS_905W_TX_V1.1
For V1.6 board i am not clear about shorting points , as you show in figure there are 4 points included two resistors. So i am confused and not sure to shorting resistors.Please help .
Buenas noches cuento con la versión CS_905W_TX_3D_V1.4 quisiera saber si el mismo software de la versión V1.3 es compatible? Sino lo es donde podría ubicarla? Muchas gracias
@@moregame2467 Oh yeah, that light doesn't mean much except that it has power. Even if it doesnt show the boot text at front, you should be able to reset it either way given you follow the instructions VERY carefully. If it doesn't work via micro SD card, then try it with the USB Burning tool.
Hi : I did download by mastic a wrong software in my ( TX3 mini -A ) after that the device died. Nothing work even there is no screen light and not work anymore.i trying to downloading the real topicals software throw the computer using the( USB burning tool ) not connect and nothing change . Only red light in the back . Now what can I do with it . Can you help me for this problem . Thank you so much.
To get this straight, you installed the wrong ROM on it and it bricked out on you. Lets try this out. Watch through 0:43 to disassemble the box. After you do that, determine your revision 1:57 (if its 1.0 to 1.2 then 3:41 for short pins) (if its 1.3 then its 3:35 for short pins).So take your USB A to A cable, the power supply of the unit, a screwdriver or tweezers, and the proper version of USB Burning Tool (look at this: forum.atvxperience.com/viewtopic.php?p=9944#p9944). Once you have that sorted, get the rom (ATVX or the OG) downloaded and loaded onto the UBT( 3:14 ). Go ahead and follow from 3:53. Thanks for commenting!
@@eduardoacevedo9993 I think it really depends on the hardware, as the later revisions support bt 5. You cannot enable something in software unless the hardware exists for it (Bluetooth emulation isn't a thing).
@@cavernoodle last night i m tring to flash it. Yes i flash it 100% succesfull burn but when i trun on tx3mini on the display no other options what should i do?? Help please Thanks for replying
Hello friend, I'm looking for information related to my tvbox TX3mini-A, with Amlogic S905W processor and the following information appears on the card: B00-MX3mini-REV 1.2. Can you help me? Oh, and it doesn't have the internal reset button, where to jam!?
It may be because of different firmwares/models all under the same name. Have you tried using a toothpick from the A/V port on the back? Is there a small nondescript hole on the bottom of the box as shown in 5:46?
My TX3 Mini Run perfectly but video doesn't Displayed on my TV. I change several HDMI cable & try 2/3 TVs. I flash stock rom successfully but result is same. this situation what should i do.. please help me out !!!!
The box might have been bricked and not flashed correctly, or one of the pins may have broken, or possibly, it just became defective. You should try the composite video out with a capable TV and one of these: www.amazon.com/HDE-Triple-Composite-Splitter-Adapter/dp/B00CIC9KW2
@@cavernoodle thanks for the clarification. I was wondering if you know the shorting points for a Sunville T9 RK3328 4GB RAM 32GB android tv box? Thanks again
What ROM are you looking for, like atvX(www.forum.atvxperience.com/viewtopic.php?f=2&t=2451) or the stock ROM (mega.nz/file/LQVy3LpR#g0WHrl4SRbMbTC2jpOKtF0PGRBTxreeOg64vtQubhuU)? Because it is v1.1 you have a wide range of options to choose from.
Hi friend, my board cs_905w_tx_v1.1 blue board. Does the USB cable and power cable need to be plugged in at the same time for a short circuit? and which one rom i can use for board... Thanks
You could have installed an incompatible rom, or messed up on some step that resulted in this. It might be bricked to no return, although if you want you can message the people at forumXperience.
Hi. I was following your tutorial but only when i disassembled the box and check the board (blue), i realised that i've got a diferent box. My is a tx3 mini-L... My version is a ""CS_905W_MiniWQ_2C_V1.2". Do you know what are the pins that i need to short?
@@cavernoodle thanks for your reply. My box is different of yours, is a mini version a bilieve.. I do not have any chip near the information of the box version =/..
@@OruamAF From what you are saying, it seems as though you need to short pins at 3:35. (You likely have a 1.3 since the NAND chip is not next to the model info, 2:23). If you have any more questions, I'm happy to help!
Tenho tx3 mini. Na hora que estava atualizando tv box, apareceu um X com Android. Depois não ligou mais e nem sinal de vida. Placa cs_905w_tx_v1.2 . Poderia me ajudar?
@@cavernoodle idk why they say its not original board but for me i was changing roms since like 2017 always using atvx way back for years . I think its just problem of drivers but i basically installed every rom out there
Hello cavemoodle i have a tanix clone the xsarius pure 4k similair to the tx3 mini . accept a other motherboard name the cs905w_tx_2c_ir_v1.0 it,s bricked iam trying to repair it for an friend of my . But i have the idea that i not the good pins short 7 and 8 also comes windows 10 with usb not recornized .Do you have info of this board or can you help me which pins i must short ? thankks in advanced
If you are trying to get a zip file or trying to get into TWRP, then yes. Sadly Amlogic only makes ROM recovery through SD card and UBT. Thanks for asking!
hola tengo la tx3 mini cs_905w_tx_v1.2 20170925 placa azul , cual rom recomiendan ya que he probado varias pero todas arrojan algun problema de uso y ya no puedo volver a la rom oficial ya que no esta en ningun lado .... Ayuda por favor
Totally here to help! In the description there is a link to the original rom for the TV Box, but I can provide it here too: mega.nz/file/LQVy3LpR#g0WHrl4SRbMbTC2jpOKtF0PGRBTxreeOg64vtQubhuU. The only good custom rom I can recommend to you is atvXperience: www.forum.atvxperience.com/viewtopic.php?f=2&t=2451. If you look around in the threads, you can find a version for 1.2 if I remember correctly. Thanks for asking!
From talking with members on the forum, getting any android version higher than 7 is impossible for the 1.3 edition due to the use of nand chips that can't get newer versions of android on them.
When no showing boot on display (nothing on display) , that means its completely knackered. Board is red color, ver CS_905W_TX_V1.2 20170925 Only red light of some kind comes from the back of the device. Thanx
For those, only the original ROM works. I think you still are able to unbrick it via UBT. Watch through 2:46, and end at 4:22. You will need to get a USB a to a cable off of Amazon for like 4 dollars, but you will have a good rate of success. If you need any more help, reply back. Thanks for commenting!
@@cavernoodle Hello mate, thanx for reply, any chance you might have or know where to download original stock ROM for it, because all i can find is OTA version of android 7.1.2, nowhere to find in .img file. Much appreciated your reply and your time.
@@dragandragan6469 Hey! Sure, I can link you a file. mega.nz/file/LQVy3LpR#g0WHrl4SRbMbTC2jpOKtF0PGRBTxreeOg64vtQubhuU is the OG rom. If you want an AndroidTV Experience, then try mega.nz/folder/GEpQmQhZ#ezNEXQdnyNIhm2axjnfTIg/file/2IYzQShJ for non-1.3, and I'll link 1.3 version as soon as possible (1:53 for revision help). Be sure to look at description for updated links.
No luck mate, tried all three methods, in the first one using UBT get message constantly [2020-10-30 08:20:00 464][HUB1-1][0x10103005]Romcode/Initialize DDR/Download buffer/Read item data failed One with SD card, nothing happened, third one definitely.
hiii bro...my tanix tx3 mini with code CS_905W_TX_3D_V1.3 20181029 is brick only red light in audio optic port, i try to flash with fw atvXperience_S905W_V2H_FINAL_TX3_NEW_REVISION.img, but alway stop in 98% process and with error message [0x30403003]UBOOT/Partition bootloader/Download buffer/Data tranfer error, do you know how to solving this error? thanks before
I have a tx3 that brcked and I can't make it work at all. always gives this error. 0x10303004 romcode/switch status/identify/ error result Model: TX3 CS 905 w TX 3D V1.6
@@cavernoodle No, I did nothing. After purchasing the TX3 mini, I just plugged it and stated to play. I don't know how to actually get started with the android box perfectly. So if you give me some directions how to get started after buying this product, it'll be so great full :)
@@musflickdesigning If you have a compatible TX3 Mini, a usb male to male cable, and some time, then you could install atvX v4, which might solve your problems. Watch the video to see if you have a 1.2 or older board, as those 1.3 ones don't work with v4 (atvX has an older version though for that). Thanks for asking!
Can you describe to me what you did (like how to installed the rom to the card, what rom you used, etc.)? Also describe what you mean when you say "totaly DEAD" (like does it show a black screen on power-up, any lights that turn on). Because if you put the right ROM on a functioning SD card, and properly followed the steps to initiating recovery, then it should've worked. I had a similar experience myself trying to install with an SD card, as they can be hit or miss. If you can, try using a USB a to a cable (here's one I used: www.amazon.com/UGREEN-Transfer-Enclosures-Printers-Cameras/dp/B00P0E3954/ref=sr_1_3?dchild=1&keywords=usb+a+to+a&qid=1602958564&sr=8-3), as they have a higher success rate.
@@cavernoodle by totaly dead i mean there is no power lights now...no boot sign,no nothing...!anyway i ordered an amazon fire stick now...no hard feelings.
my solution. 1. hold the RESET button 2. plus the USB cable to the port on TX3mini near TF slot ( DON'T NEED PLUG 5V ADAPTOR) 3. You will see " connected" in the buring tools
@Abdulhadi Faris It would be a bit easier on my end if we do it over RUclips. Can you explain in detail what you see after disassembly of the unit? Like is it a red board (1:40), what revision is it (1:55), perhaps link a image if need be. Thanks for your question!
@@cavernoodle This is the first side ibb.co/Xzj7tx8 This is the second ibb.co/bPpxY7c I don't know which pins to short because the nand isn't the same in video
@@abdulhadifaris8624 The board says that its a 1.0, but the layout is nothing like 2:13, a real 1.0 board. This might be a fake, but since I don't know anything about this board, you will have to talk to the people over at forum.atvxperience.com , they have ALOT of experience in TV boxes, so they are your best bet.
my tx3 mini is a fake one with a blue motherboard. Previously it was on boot loop but after installing the firmware from sd card it got bricked. What can i do now? Please help.
hola tengo una placa tx3 mini (cs_905w_tx_2c_v1.1 20180206)placa roja cual rom me recomiendan ya que he probado varias pero todas arrojan algun problema de uso y ya no puedo volver a la rom oficial ya que no esta en ningun lado .... Ayuda por favor
Since it is a red board and ROM compatibility is very hit or miss, I would say looking on the manufacturer's website for the original ROM or atvX, but since it's nowhere to your knowledge, and I don't have enough knowledge in this field, I could direct you to the atvXperience forums (www.forum.atvxperience.com)who might be able to help. If you could link some high res images of both sides of the board here, then it would help (like imgbb.com/). I hope I helped!
Check out www.forum.atvxperience.com/ for technical help!
mine shows CS_906W_TX_3D_V1.3, I tried upgrading using your video link with SD CARD but unfortunately it doesn't boot up anymore, because when i was pressing reset with a pin, i flipped and i wanted to repeat the process from a fresh. but now i messed up kindly assist
@@aliathman8755 You'll have to buy a USB A to A cable and follow the guide from 2:47
So many thanks pal! Finally I could figure out how to dissamble a TX9 TV box!!! Thanks again!!!
No problem. Happy to help someone else out!
Hello I have v1.2 how can I short-circuit it when installing the software? Thanks for help.
translate to Turkish
I'm stuck on the "Upgrading" screen (SD card method)
Any help ?
Дякую за допомогу , я ніде не міг знайти де знаходиться test point , thanks man 🎉
I used this as a starting point to install atvxperience (AidanROM), but I bricked my TX3 Mini in the process. From there, I tried several different stock ROMs attempting to fix it, with no success. My board is blue and it says CS_905W_TX_V1.1
Fantastic guide!!!!!
For V1.6 board i am not clear about shorting points , as you show in figure there are 4 points included two resistors. So i am confused and not sure to shorting resistors.Please help .
You should try each set, individually, of metal contact points in the red circle, except for the transistors.
Buenas noches cuento con la versión CS_905W_TX_3D_V1.4 quisiera saber si el mismo software de la versión V1.3 es compatible? Sino lo es donde podría ubicarla? Muchas gracias
My box is showing red light...is there any way I restore it ...thks
Can you clarify when you mean "red light"? Like where is this red light? If possible, try to link an image of the issue.
@@cavernoodle Me too, the red light is on the SPDIF connector
I am waiting for a response from the warranty, so I haven't handled it yet
@@moregame2467 Oh yeah, that light doesn't mean much except that it has power. Even if it doesnt show the boot text at front, you should be able to reset it either way given you follow the instructions VERY carefully. If it doesn't work via micro SD card, then try it with the USB Burning tool.
@@cavernoodle i need help, i decided to use USB burning tool, after done i plug in power and hdmi cable to tv box it just shows green
Hi : I did download by mastic a wrong software in my ( TX3 mini -A ) after that the device died. Nothing work even there is no screen light and not work anymore.i trying to downloading the real topicals software throw the computer using the( USB burning tool ) not connect and nothing change . Only red light in the back . Now what can I do with it . Can you help me for this problem . Thank you so much.
To get this straight, you installed the wrong ROM on it and it bricked out on you. Lets try this out. Watch through 0:43 to disassemble the box. After you do that, determine your revision 1:57 (if its 1.0 to 1.2 then 3:41 for short pins) (if its 1.3 then its 3:35 for short pins).So take your USB A to A cable, the power supply of the unit, a screwdriver or tweezers, and the proper version of USB Burning Tool (look at this: forum.atvxperience.com/viewtopic.php?p=9944#p9944). Once you have that sorted, get the rom (ATVX or the OG) downloaded and loaded onto the UBT( 3:14 ). Go ahead and follow from 3:53. Thanks for commenting!
Hola.. A este box se puede conectar un adaptador bluetooth V5.0
The later revisions do support bluetooth 5, I think. How would you add bluetooth to a tv box? 🤔
Ok.. Alguna ROM que sea compatible para instalar que lo utilicen
@@eduardoacevedo9993 I think it really depends on the hardware, as the later revisions support bt 5. You cannot enable something in software unless the hardware exists for it (Bluetooth emulation isn't a thing).
Sir I have updated firmwate when it was stuck on logo after update it is agin facing same problem, what to do now sir please help
i bought tx3mini-a cs_905w_tx_3D_v1.3 . but suddenly not boot displaying tx3mini and hang on no other options. please help what should i do?
Have you tried to reset it with the last method?
@@cavernoodle what’s the last method im new
@@cavernoodle last night i m tring to flash it. Yes i flash it 100% succesfull burn but when i trun on tx3mini on the display no other options what should i do?? Help please
Thanks for replying
@@NewTech7431 It should have shown an image once it's flashed, maybe some other component has also failed.
Hi bro... If i get error uboot/get results/diskinitial error
What should i do?
Depends, but usually it means that you are trying to install incompatible software to the target device.
Thanks. I have unbricked my m9c max . The pins need to be short without the use of power supply.
i have a tx6 and it boots into recovery mode by default, doing factory reset/cache reset does nothing. It goes back to recovery mode.
Better to go the USB method then to flash the stock firmware.
Just once flesh sucesufull, after that error: cannot erase bootloader? please help
Hello friend, I'm looking for information related to my tvbox TX3mini-A, with Amlogic S905W processor and the following information appears on the card: B00-MX3mini-REV 1.2. Can you help me? Oh, and it doesn't have the internal reset button, where to jam!?
In my box i could not go to recovery menu by following all stpes
It may be because of different firmwares/models all under the same name. Have you tried using a toothpick from the A/V port on the back? Is there a small nondescript hole on the bottom of the box as shown in 5:46?
My TX3 Mini Run perfectly but video doesn't Displayed on my TV. I change several HDMI cable & try 2/3 TVs. I flash stock rom successfully but result is same. this situation what should i do.. please help me out !!!!
The box might have been bricked and not flashed correctly, or one of the pins may have broken, or possibly, it just became defective. You should try the composite video out with a capable TV and one of these: www.amazon.com/HDE-Triple-Composite-Splitter-Adapter/dp/B00CIC9KW2
Hi I have a v1.4 how do I short when installing the firmware? thanks for the help.
You need to short the same pins that the revisions before also used. Thanks
@@cavernoodle thanks for the clarification. I was wondering if you know the shorting points for a Sunville T9 RK3328 4GB RAM 32GB android tv box? Thanks again
@@kofiannor5722 Sorry, I do not.
hello my board cs_905w_tx_2c_v1.1 (blue board) can give me download link for my rom? or which one rom i can use for my board? tq
What ROM are you looking for, like atvX(www.forum.atvxperience.com/viewtopic.php?f=2&t=2451) or the stock ROM (mega.nz/file/LQVy3LpR#g0WHrl4SRbMbTC2jpOKtF0PGRBTxreeOg64vtQubhuU)? Because it is v1.1 you have a wide range of options to choose from.
Hi friend, my board cs_905w_tx_v1.1 blue board. Does the USB cable and power cable need to be plugged in at the same time for a short circuit? and which one rom i can use for board... Thanks
hello sir i have installed rom but after burning successfull i plug into tv and it shows me green screen and after that my pc is not detecting usb
You could have installed an incompatible rom, or messed up on some step that resulted in this. It might be bricked to no return, although if you want you can message the people at forumXperience.
Good day, can i have a link for an IMG of V 1.3? The link you have given is not available now. thnx.
The link went broken a while ago, just use the think from their website: www.tanix-box.com/download-view/tanix-tx3-mini-firmware-full-image-20170829/
You are awesome so thx from Turkey Sd card method works for me
I tried to unbrick it with toothpick but it stays on boot and later go to clock
You have to update it via SD Card or USB burning tool in order to unbrick it in most scenarios.
I have a revision of the board 1.0, please tell me who knows where to find the closure point to restore
Hi. I was following your tutorial but only when i disassembled the box and check the board (blue), i realised that i've got a diferent box. My is a tx3 mini-L... My version is a ""CS_905W_MiniWQ_2C_V1.2". Do you know what are the pins that i need to short?
The 1.2 shorts should be at 3:40, thanks for your question!
@@cavernoodle thanks for your reply. My box is different of yours, is a mini version a bilieve.. I do not have any chip near the information of the box version =/..
@@OruamAF From what you are saying, it seems as though you need to short pins at 3:35. (You likely have a 1.3 since the NAND chip is not next to the model info, 2:23). If you have any more questions, I'm happy to help!
Tenho tx3 mini. Na hora que estava atualizando tv box, apareceu um X com Android. Depois não ligou mais e nem sinal de vida. Placa cs_905w_tx_v1.2 . Poderia me ajudar?
Best to use the pin method first.
V1.2 anakart için hangi atvexperince rom lütfen link paylaşın
So.....I'm your first subscriber!
This is a moment worth celebrating.
tem a Rom para essa placa cs_905w_tx_v1.2?
www.tanix-box.com/download-view/tanix-tx3-mini-firmware-full-image-20170829/
Mega download for 1.6 not exist anymore... please help..
You mean for atvXperience? I'll get a new link once their site is up.
I have the red motherboard and i been installing all roms on it , there is a way to short pin that motherboard too. I hope this comment was helpful
The video was made a while back when red boards didn't have the functionality for installing roms, but its good to hear that that has changed.
@@cavernoodle idk why they say its not original board but for me i was changing roms since like 2017 always using atvx way back for years . I think its just problem of drivers but i basically installed every rom out there
@@aminebadri2849 I believe there are limitations to installing custom roms on red board tv boxes
@@cavernoodle nope no limit as long as it say this rom for tanix tx3 ,i can install it .
@@aminebadri2849 Can you tell me which pin to short, i also have red motherboard
Para un T9 sabes cómo hacer unbrick
Try this: ruclips.net/video/c5pga5bGVl0/видео.html
Hello cavemoodle i have a tanix clone the xsarius pure 4k similair to the tx3 mini . accept a other motherboard name the cs905w_tx_2c_ir_v1.0 it,s bricked iam trying to repair it for an friend of my . But i have the idea that i not the good pins short 7 and 8 also comes windows 10 with usb not recornized .Do you have info of this board or can you help me which pins i must short ? thankks in advanced
Thanks for using atvX forum, as they helped out more then I ever could.
can i use a pen drive instead of sd card.
If you are trying to get a zip file or trying to get into TWRP, then yes. Sadly Amlogic only makes ROM recovery through SD card and UBT. Thanks for asking!
Hello Brother The IMG file of TX3 Mini is not available can u give me a drive uploaded link pls
Should be available now
hola tengo la tx3 mini cs_905w_tx_v1.2 20170925 placa azul , cual rom recomiendan ya que he probado varias pero todas arrojan algun problema de uso y ya no puedo volver a la rom oficial ya que no esta en ningun lado .... Ayuda por favor
Totally here to help! In the description there is a link to the original rom for the TV Box, but I can provide it here too: mega.nz/file/LQVy3LpR#g0WHrl4SRbMbTC2jpOKtF0PGRBTxreeOg64vtQubhuU. The only good custom rom I can recommend to you is atvXperience: www.forum.atvxperience.com/viewtopic.php?f=2&t=2451. If you look around in the threads, you can find a version for 1.2 if I remember correctly. Thanks for asking!
@@cavernoodle i need this help but the forum is temporarily Unavailable
@@aldytvnet2635 The forum does go offline sometimes, just check often.
"tx3mini-a cs_905w_tx_3d_v1.3"
I need to go android 8 or 9 😢 I need help plz
From talking with members on the forum, getting any android version higher than 7 is impossible for the 1.3 edition due to the use of nand chips that can't get newer versions of android on them.
Hi, my tx3 mini doesn't turn on, any solution?
Did you watch through the ENTIRE video? I'm serious because most of the info is on there. Once you finished it all then come back.
When no showing boot on display (nothing on display) , that means its completely knackered. Board is red color, ver CS_905W_TX_V1.2
20170925
Only red light of some kind comes from the back of the device. Thanx
For those, only the original ROM works. I think you still are able to unbrick it via UBT. Watch through 2:46, and end at 4:22. You will need to get a USB a to a cable off of Amazon for like 4 dollars, but you will have a good rate of success. If you need any more help, reply back. Thanks for commenting!
@@cavernoodle Hello mate, thanx for reply, any chance you might have or know where to download original stock ROM for it, because all i can find is OTA version of android 7.1.2, nowhere to find in .img file.
Much appreciated your reply and your time.
@@dragandragan6469 Hey! Sure, I can link you a file. mega.nz/file/LQVy3LpR#g0WHrl4SRbMbTC2jpOKtF0PGRBTxreeOg64vtQubhuU is the OG rom. If you want an AndroidTV Experience, then try mega.nz/folder/GEpQmQhZ#ezNEXQdnyNIhm2axjnfTIg/file/2IYzQShJ for non-1.3, and I'll link 1.3 version as soon as possible (1:53 for revision help). Be sure to look at description for updated links.
@@cavernoodle Mate, thank you for uploading OS. Will let you know of outcome in the morning, around 6 hours from now.
Cheers again.
No luck mate, tried all three methods, in the first one using UBT get message constantly
[2020-10-30 08:20:00 464][HUB1-1][0x10103005]Romcode/Initialize DDR/Download buffer/Read item data failed
One with SD card, nothing happened, third one definitely.
How unbrick tx3 mini b4 s912
I only know the S905w version of the TX3 Mini. Sorry!
hiii bro...my tanix tx3 mini with code CS_905W_TX_3D_V1.3 20181029 is brick only red light in audio optic port, i try to flash with fw atvXperience_S905W_V2H_FINAL_TX3_NEW_REVISION.img, but alway stop in 98% process and with error message [0x30403003]UBOOT/Partition bootloader/Download buffer/Data tranfer error, do you know how to solving this error? thanks before
Try again because first time mine same like yours 98% and then I try again get 100%
bro...where is the short pin for red board cs_905w_tx_v1.2 20170925?
Than you! Very helpful.
HAVE FIRMWARE S905X V1.2 OTTTVBOX X96 PLEASE
Sorry dude, I only had images for S905W. Thanks for asking though
V1.2 anakart var kısa pin nasıl yapılır resimli tarifi lütfen
OMG!!!!!!!!!!!!!!!!! it worked...!!!! Hurrayyyyyyyyyy....my 'brick" is unbricked!!!!!
Glad it helped you out!
@@cavernoodle do u know how to unbrick T9 Tv box? Appreciate yr video..
I have a tx3 that brcked and I can't make it work at all. always gives this error. 0x10303004 romcode/switch status/identify/ error result
Model: TX3 CS 905 w TX 3D V1.6
You might be using an incorrect rom on it, try looking for TX3 Mini v1.6 roms
Big thank you bro.
Yep, no problem.
thanks for sharing tx3 mini v1.3 firmware...
Alguien sabe el pin corto de la Tx3 mini-a SC_912_TX_B4_V1.0 ? tengo fotos de la placa
You should consult the forums because I think it is s912 you are talking about. forum.atvxperience.com/
It deleted all my film channels how do I get into my memory recycle
You will probably have to reinstall them, as unbricking wipes everything.
can it work for tx6
It might, you'll have to post pictures of the motherboard so I could tell.
I'm facing a WiFi disconnecting problem in my TX3 Mini. If you make a video on it, it'll be so greatful to me :)
I think I remember a forum thread about that. Did you install atvXperience onto it?
@@cavernoodle No, I did nothing. After purchasing the TX3 mini, I just plugged it and stated to play. I don't know how to actually get started with the android box perfectly. So if you give me some directions how to get started after buying this product, it'll be so great full :)
@@musflickdesigning If you have a compatible TX3 Mini, a usb male to male cable, and some time, then you could install atvX v4, which might solve your problems. Watch the video to see if you have a 1.2 or older board, as those 1.3 ones don't work with v4 (atvX has an older version though for that). Thanks for asking!
Did notwork for me!
thank you bro !!!!!!111111
I used method 2 because i didnt have a usb cable....my tv box is totaly DEAD now..just saying
Can you describe to me what you did (like how to installed the rom to the card, what rom you used, etc.)? Also describe what you mean when you say "totaly DEAD" (like does it show a black screen on power-up, any lights that turn on). Because if you put the right ROM on a functioning SD card, and properly followed the steps to initiating recovery, then it should've worked. I had a similar experience myself trying to install with an SD card, as they can be hit or miss. If you can, try using a USB a to a cable (here's one I used: www.amazon.com/UGREEN-Transfer-Enclosures-Printers-Cameras/dp/B00P0E3954/ref=sr_1_3?dchild=1&keywords=usb+a+to+a&qid=1602958564&sr=8-3), as they have a higher success rate.
@@cavernoodle by totaly dead i mean there is no power lights now...no boot sign,no nothing...!anyway i ordered an amazon fire stick now...no hard feelings.
@@exitpc Alright then, thanks for commenting anyway.
👍👍👍👍
cs_905w_tx_v1.2 red pcb someone have firmware?i think is a fake tx3 mini
my board es 1.4
Try this: www.forum.atvxperience.com/viewtopic.php?f=2&t=3140&p=16165#p16165
my solution. 1. hold the RESET button 2. plus the USB cable to the port on TX3mini near TF slot ( DON'T NEED PLUG 5V ADAPTOR) 3. You will see " connected" in the buring tools
This only works if your box isn't bricked, but I couldn't unbrick my box without the power source. TV boxes have their own minds sometimes...
Hi can i message u on telegram mine is bricked and the board ia diffrent plz help
@Abdulhadi Faris It would be a bit easier on my end if we do it over RUclips. Can you explain in detail what you see after disassembly of the unit? Like is it a red board (1:40), what revision is it (1:55), perhaps link a image if need be. Thanks for your question!
@@cavernoodle
This is the first side
ibb.co/Xzj7tx8
This is the second
ibb.co/bPpxY7c
I don't know which pins to short because the nand isn't the same in video
@@abdulhadifaris8624 The board says that its a 1.0, but the layout is nothing like 2:13, a real 1.0 board. This might be a fake, but since I don't know anything about this board, you will have to talk to the people over at forum.atvxperience.com , they have ALOT of experience in TV boxes, so they are your best bet.
@@abdulhadifaris8624 To narrow your search for them, tell them that it is a s912 box. I think they have a dedicated section for those boxes.
0x10302001 romcode/switch status/check connect/enum device tanix mini e probamos muchas rom y emtodas ese error
I am the marketing manager of tanix tv box. I want to cooperate with you on the latest products. How can I contact you?
my tx3 mini is a fake one with a blue motherboard. Previously it was on boot loop but after installing the firmware from sd card it got bricked. What can i do now? Please help.
hola tengo una placa tx3 mini (cs_905w_tx_2c_v1.1 20180206)placa roja cual rom me recomiendan ya que he probado varias pero todas arrojan algun problema de uso y ya no puedo volver a la rom oficial ya que no esta en ningun lado .... Ayuda por favor
Since it is a red board and ROM compatibility is very hit or miss, I would say looking on the manufacturer's website for the original ROM or atvX, but since it's nowhere to your knowledge, and I don't have enough knowledge in this field, I could direct you to the atvXperience forums (www.forum.atvxperience.com)who might be able to help. If you could link some high res images of both sides of the board here, then it would help (like imgbb.com/). I hope I helped!