Это видео недоступно.
Сожалеем об этом.
Arduino Automatic WaterPump System.. //Save Water💧
HTML-код
- Опубликовано: 8 ноя 2019
- ★Hey friends this is "Sci&Tech" Creator of Arduino Experiment // Sci Experiment ,, Today I will show you "Arduino Automatic WaterPump System"..//Save Water💧//..
If you like that hit the like button 👍 & don't forget to bell icon ((🔔)) ~~ subscribe to my channel for more videos..
★Arduino Experiment✨
_________________
//Automatic WaterPump System Pin Connection's~~
★1) Ultrasonic Sensor~~
Connect ultrasonic sensor's VCC and gnd pin to 5v and GND of aduindo board respectively.Now connect echo pin to digital pin 7 and trig pin to digital pin 8 on board.
_
★2) Pizo Buzzer~~
Connect Pizo Buzzer positive pin connect to arduino digital pin 9 and, Pizo Buzzer negative pin connect to arduino GND pin.
_
★3) Red LED~~
LED positive pin connect to arduino digital pin 9 and, LED negative pin connect to arduino GND pin.
_
★4) Relay Module~~
Connect power(center) pin of module to positive terminal of battery and gnd(right) of module to bread board which in turn will be connected to negative terminal of battery and gnd of arduino board. And relay signal pin connect to arduino digital pin 10.
_
(Note:- We are using a bread board because we have to connect gnd pin of relay module to negative terminal of battery and also with gnd of arduino board.Remember we have to always connect negative terminal of external power supply(like battery) to gnd.)
_
Now replace the switch of the water pump with relay by connecting the two wires of switch to normally closed(left) and common(center) outlet of the relay module.
★Working~~
Place the ultrasonic sensor on top of the tank. Ultrasonic sensor calculates the distance and according to the code if distance is less than or equal to 5cm it switch offs the pump and if the distance is grater than 80(which is recommended to be changed according to your need) the relay turn on the pump.
_
(Note:- Ultrasonic sensor is placed at the top hence if the distance increases it means level of water is decreasing and vice-versa.)
________________
★Needed Components Online Link ≈
★Indian link for buying 🛍.....
★FlipKart.Com ~~
*Arduino Nano Module~~
Easy Electronics Arduino Nano V3.0 Micro Controller Board Electronic Hobby Kit
dl.flipkart.com...
*Ultrasonic Sensor~~
Diy Arduino Compatible HC-SR04 Ultrasonic/Sonar Distance Sensor Module
dl.flipkart.com...
*Relay Switch Module~~
REES52 5VRELAY One Channel 5V Relay Module for Arduino Raspberry Avr Pic Low Level Trigge Electronic Components Electronic Hobby Kit
dl.flipkart.com...
*Pizo Buzzer~~
APTECHDEALS Piezo 5v Buzzer Pack of 5 Pc
dl.flipkart.com...
*LED's ~~
dangi e shop DES00REDLED3MM Electronic Components Electronic Hobby Kit
dl.flipkart.com...
*5v. 1Amp DC-Adopter~~
maxTREE 5V 1A DC Power adapter Sony & DC Pin Connector Charger for arduino board ,Router, Modem, cctv and other Worldwide Adaptor
dl.flipkart.com...
_______________________
____________
★Arduino Sketch~~
sayan543210.wi...
...............................................................................
★Follow me on social sites 👥~~
*FaceBook page~~
/ science-experiment-282...
*FaceBook group~~
/ 370470473704090
*Instagram~~
/ sayan.jpeg
/ arduino_experiment
~~~~~~~~
~~~~~~~~~~~~~
★Music ♪♪♪♪♪♪🎶🎶
*RUclips Audio Library Music..
&
*RUclips No Copyright Vlog Music..
_________________
// #Automatic_Waterpump
// #Save_Water💧
// #ArduinoExperiment
____________
▶LIKE ,, SHARE ,, COMMENTS ,, SUBSCRIBE
★Don't Forget To Like & Subscribe★
~~Thank's For Watching~~
Танк на 1000 литров успешно работает, чувак, хороший учебный человек. :)
Limitations of that idea are:
-In extreme environmental conditions, the sensor will therefore operate unstable when affected by temperature.
-The installation on the tank is difficult if you do not use a solid cover to prevent electrical and water penetration.
I wish "Arduino Experiment" answers this questions. That only for a better information. Project is very good. We need pay attention in details.
Float Pump is the option here. i dont think Ultrasonic will do any work.
All detail provide you are grat
Thanks for the ideas,, for those questioning about the condition of a ultrasonic sensor in that kind of environment,, FYI this video is aonly a prototype in real world theirs a appropriate sensor for that and that is an Industrial Ultrasonic sensor imand the price is approximately 11k up,,,
Nice job
It doesn't work in a closed tank, because of ultrasonic sound bouncing.
And humidity will destroy the sensor soon.
But it has been set in my house for about 3 years, it is working fine .....
My tank is 1000lt .... And it's still working great .... 😶
depends on how much power ... if the signal is too strong yes that is possible but these sensors/senders are pretty weak
Thanks for your work! Any ideas for a school auto alarm system as my graduating project? Useful video links would be awesome! Just power on/off at specific time with web support maybe. Thanks in advance!
thanks alot
Always Welcome! 🥰
Will the ultrasonic sensor work when water evaporates from the tank and deposit on receiver and transmitter of ultrasonic sensor??
This is a very important question. !!!!!
@@williamarredondo6833 yes and no i have made same project long back, had to change the sensor every 4 -5 months due to corrosion from water vapours
Good day, what software did you use in creating those circuit diagram?
TinkerCad ..
link here -
www.tinkercad.com/dashboard
Is the pump will pump the water automatically when the led turn red? Or we need to press it?
Place the ultrasonic sensor on top of the tank. Ultrasonic sensor calculates the distance and according to the code if distance is less than or equal to 5cm it switch offs the pump and if the distance is grater than 80(which is recommended to be changed according to your need) the relay turn on the pump.
(Note:- Ultrasonic sensor is placed at the top hence if the distance increases it means level of water is decreasing and vice-versa.)
//No Red Led is Indicator ....
//When the water is filled in the tank, the pump will automatically turn off & when the water in the tank runs out, the pump will automatically turn on again......
//We don't have to switch on and off ......
I have a question. Is it possible to make a system with:
1. moisture sensor
2. water pump
3. water volume meter
in just one arduino? or i requires 2?
Yes ofcourse possible to make ..
@@ArduinoExperiment can you make a video regarding the moisture sensor, water flow sensor (to measure the volume flowing), and a pump
Sir, what is the total current the circuit is taking? Kindly reply how to measure it
5-6V DC. for total Aruino Circuit! ..
This is really a great idea. Any idea if I to include an alarm system in that system? Like if the tank is full an alarm will be triggered. Which components can I use? Useful video links would be awesome!
Yes Just add the Buzzer on pin no Arduino D9 Pin ..
@@ArduinoExperiment Okay thank you.
@@naemytuutaleni658
You're welcome .. thanks for supporting us . . . .
Don't forget to Like & Subs 🙌🏻❤️
Hope you Enjoyed this channel Videos ..
keep Making .. Stay Safe
Is it possible make a pcb for this circuit and another doubt is the do the wirings change when I use arduino uno so what changes do I need to mak e could you upload a code for arduino uno too.Thank you
How durable is HC-SR04 to be used in such humid environment? I believe these sensors would eventually fail due to formation of water droplets.
I just expoxied one to see how it stands against water and corrosion over time
@@cjdelphi how did it go ?
Any updates? 🙂
@@itsmmdoha still going, and wow 3 months already! lol
still vibin; with this music! nice edit bruh
★Thank you so much🙂
Thanks for your support!!✨
Idea is great and planning to implement at this circuit at my home ,but i have following doubts?
Whether this ultrasonic sensor will withstand the water evaporated inside the tank and able to withstand the temperature inside the tank?
★There will be no damage, it has been set in my house for about 1 year and it is still going well. . . . .
Yes, sweat comes from water, so the sensor has to cover it in a 3D printed box,, Otherwise the sensor may go damage.....
@@ArduinoExperiment glad to hear it's working good for you, but after spending 35+ years in the oil/gas instrumentation field even the big names of the industry had a hard time designing a decent ultrasonic level system that was free from problems.
Bro really thanks for information . Can it will work in case of summer sable pump
Can this relay really could be used in 220volt??
Yeah !
Can Arduino be used to produce business goods? What is your opinion on this?
🤔Yes ofcourse!
Please koi mujhe electronics padhao yaar..
Bahut weak hu mai isme
Kaun sa wire kidhar jodna hai nahi pata mujhe.
Please yaar help karo
By the way....project was awesome
Check it out Video Description.. ~ Arduino Circuit diagram & also Wireing details....
bro can u help .how i attach a16*2 display in this circuit and can u send the code for that
.....pls...
Can I use it for 1000 liters tank? nice video! Thanks for reply.
Yes!!
Arduino Code link in description . . . .
//For Big Water Tank (1000 litters) . . . .
Thank you for your support 🙌❤️
@@ArduinoExperiment
Can I use 10amp relay for 1 horsepower pump
@@anupsarkar3063 it's better to use contactor, you can use the relay to control the contactor.
is the blue wire from the relay to the water pump positive?
Yes!.
Can someone help me to wrote the code similar with this project?
Sir please can u Tell what is the exact quantity in litre of big tank program code u have given,, e.g 500L or 100L?
Where are you from? I have a project like this. Waiting for your reply.
I'm from India..
@@ArduinoExperiment . Exotic place. India is full of high Technical people..... With tigers, cobras, etc.
which software did you use to draw your circuit?
hello, how can i make it that i will have the pump inside and it will turn on if the tank is full so it would push the water out and stop pumping after the container is empty?
🌷🌷🌷💚🌷🌷🌷
Can't I use an arduino uno in this? Need help just for project purposes, Thank you.
Same ... Arduino Nano Or Arduino UNO ..
Same Code .. same Pin ....
You can use Arduino UNO Board.... 👍🏻
@@ArduinoExperiment Great! Thanks for the info. :)
will you show the code for this project bro
nice video bro.....
Thank You So Much. . . . .🙂✨
Thank you for your support. . 🤗❤
Ap ne battery 🔋 kune use keep relay k sath jb k hum USB se power da rha han
I have a few questions, how to operate this circuit if im using a 12v solenoid valve, do i need voltage regulator for 12v since arduino uno only supports 5v and how to supply the solenoid valve?
You can use a relay to power the valve, the relay can be operated by nano
Can I use It for 200 litres tank?nice video!reply plz
In my house, I tried a 1000 liter tank and saw that it was working ,, It will also work in your tank . . . .
//If the 1st code does not work then there is 2nd code in the description . . . .
PleSe dont add the music...it makes my head feel heavy. The content is nice though. Gonna do this today
0:24 Is that the same as a piezo buzzer?
Yes!! It's Piezo Buzzer . . . .
can we use 5v battery instead of 5v adaptor
Yes you can use it,, but you'll have to change the battery a multiple times.... And that would be a waste of time.....
can i use arduino uno instead of arduino nano?
Yes..
No problem,, Can use the Arduino Uno.
Sir, can we do this project from Arduino uno board
Yes you can do
Yes!! Ofcourse. . . . .
Why in video and Arduino sketch is different?? Plz reply me
What software use for the simulation??
I used video editing software😅😅 ,, downloaded and added a png photo ,, cut and pasted it and animated it . . . .
LOL, thanks for answering, great video :)
Hahaha😁😅
Thank you so much 🙌❤️✨
Sir below is my code for automatically water level indicator using ultrasonic sensor but I want to add buzzer if the water reaches full tank buzzer should on for 10 seconds then the buzzer should stop
..
..........................................
const int trigPin = 2;
const int echoPin = 3;
int ledA = 13;
int ledB = 12;
int ledC = 11;
int ledD = 10;
int ledE = 9;
int buzzer = 8;
int A = 20;
int B = 16;
int C = 12;
int D = 8;
int E = 5;
int max_distance = 200;
void setup() {
Serial.begin(9600);
pinMode (ledA, OUTPUT);
pinMode (ledB, OUTPUT);
pinMode (ledC, OUTPUT);
pinMode (ledD, OUTPUT);
pinMode (ledE, OUTPUT);
pinMode (buzzer, OUTPUT);
digitalWrite(ledA, LOW);
digitalWrite(ledB, LOW);
digitalWrite(ledC, LOW);
digitalWrite(ledD, LOW);
digitalWrite(ledE, LOW);
digitalWrite(buzzer, LOW);
}
void loop() {
long duration, inches, cm;
pinMode(trigPin, OUTPUT);
digitalWrite(trigPin, LOW);
delayMicroseconds(2);
digitalWrite(trigPin, HIGH);
delayMicroseconds(10);
digitalWrite(trigPin, LOW);
pinMode(echoPin, INPUT);
duration = pulseIn(echoPin, HIGH);
cm = ( duration / 29 ) / 2;
inches = cm * 0.393701;
inches = microsecondsToInches(duration);
cm = microsecondsToCentimeters(duration);
if (inches < max_distance) {
Serial.print(inches);
Serial.print("in");
Serial.print(cm);
Serial.print("cm");
Serial.println();
delay(100);
digitalWrite (ledA, HIGH);
}
if (inches >= A) {
digitalWrite (ledA, HIGH);
digitalWrite (ledB, LOW);
digitalWrite (ledC, LOW);
digitalWrite (ledD, LOW);
digitalWrite (ledE, LOW);
}
else if (inches >= B) {
digitalWrite (ledA, LOW);
digitalWrite (ledB, HIGH);
digitalWrite (ledC, LOW);
digitalWrite (ledD, LOW);
digitalWrite (ledE, LOW);
}
else if (inches >= C) {
digitalWrite (ledA, LOW);
digitalWrite (ledB, LOW);
digitalWrite (ledC, HIGH);
digitalWrite (ledD, LOW);
digitalWrite (ledE, LOW);
}
else if (inches >= D) {
digitalWrite (ledA, LOW);
digitalWrite (ledB, LOW);
digitalWrite (ledC, LOW);
digitalWrite (ledD, HIGH);
digitalWrite (ledE, LOW);
}
else if (inches >= E) {
digitalWrite (ledA, LOW);
digitalWrite (ledB, LOW);
digitalWrite (ledC, LOW);
digitalWrite (ledD, LOW);
digitalWrite (ledE, HIGH);
}
else {
digitalWrite (ledA, HIGH);
digitalWrite (ledB, HIGH);
digitalWrite (ledC, HIGH);
digitalWrite (ledD, HIGH);
digitalWrite (ledE, HIGH);
}
}
long microsecondsToInches(long microseconds) {
return (microseconds / 74) / 2;
}
long microsecondsToCentimeters(long microseconds) {
return (microseconds / 29) / 2;
}
What should i do if i want to use the pump to release all the water from the tank? Please someone help me😭😭
Hi sir, can I get the schematic diagram for this system? Like you shown in the video?
Take a screenshot
@@icariusian You're great! Thanks to help🙌🏻
how to use this system at home for pumping water in overhead tank(220v connection)? can you please give what modification i have to make?
Yes!!
You can change the relay switch,
See how many amps your pump is and buy a relay and add it to Arduino. . . . .
__________________
and ,, I gave the real water pump 220v- Arduino code link in the description . . . . . .
what pump should i get? and their connection?
Hi bro can I use arduino uno in this project
★Yes!! You can use UNO board.. no problem..
how to automatic on and off for 400v 3phase motor.
I need the code please.
You can see the description box,
Code link in description..
Check it out Video Description.. ~ Arduino Circuit diagram & also Wireing details..
It will not work because the relay can't handel the 15amp current. Overheat will destroy the circuit.
If you use the 15 ampere's relay switch, then it will work......
where should i place the buzzer?
The Buzzer may or may not give it....
Pizo buzzer that you used ? Where did you put it ?
// Pizo Buzzer~~
Connect Pizo Buzzer_ positive pin connect to arduino digital pin 9 and, Pizo Buzzer negative pin connect to arduino GND pin....
LED & Pizo Buzzer Connect to Arduino D9
Okayyy thank you
Nice project..i have one question, my sumersible has control board like typical control board having voltage and ampere meter box, i have to check ampere meter reading once motor is on, if it's more than point 6..i have to switch off the motor else it will burn. How can i manage this using Arduino?
Did You mean pushing start button ?
will this code work for arduino uno
Yup..
@@ArduinoExperiment thank u😊
in code a is not defined error occur
did you have the flowchart of this project?
No, I didn't have a flowchart.... I created the code by calculating how big the water tank is and, the distance of the ultrasonic sensor.....
@@ArduinoExperiment hi. how do you calculate and know the water tank? and by that, how can u correlate and ensuring that specific level, your ultrasonic sense the water level to give signal to arduino?
Can you explain program in detail plz
No real test in the video.
So it is not practical
fit
80mm? Please
yaar code bhi upload kr di kro professor saaaab
Check the description ..
jab 50/60 wire use karte hai to sensor work nahi karta kay karna chahiye sir ji
Usko aur power ki jarurat h.
50/60 wire me 5volt bahut kam h
d=d/69 what is the meaning of this urgent bro
Bhai program muko ne
Code seems error
Check it out on video description . . . .
I gave the link to the new code . . . .
//Code for Small & Big Water Tanks . . . .
Code?
Code link in video description . . . . Check out . . . .
Helli bhai diagram dona
I used this code it's not working
How fit is your water tank ?
//My code is for big tank . . . .
How big is your water tank ? 🤔
500 liters
Check it out on video description . . . .
I gave the link to the new code . . . .
//Code for Small & Big Water Tanks . . . .
I message you on fb but not replied my question would you please reply me bro.... kumar naresh my id name
Ok tq bro
No do sir ji