How to Fix a HomePod that Won't Power On; The Most Common Inside the A1639

Поделиться
HTML-код
  • Опубликовано: 8 янв 2025

Комментарии • 255

  • @edwingoh22
    @edwingoh22 5 дней назад

    I just attempted the HomePod tear down after months of procrastination. Your video is amazing, highlighting the potential areas to avoid. Definitely a A+ from me.

  • @rampak1
    @rampak1 9 месяцев назад +4

    Managed to repair a HomePod brought to our Repair Cafe - customer was going to throw it away if we couldn't fix it. Some aspects of the repair were quite challenging: the glue seemed to be much stronger than on the one in the demo. I couldn't detach the glued-in ribbon cable without putting a dent in it, and the clamp for the ribbon cable at the bottom of the unit fell off: I had a devil of a job to put it back and was not sure if it was working. Also when removing the diode I managed to dislodge the tiny capacitor next to it - a frustrating 40 minutes getting it back in place!
    I was absolutely amazed when after all that it worked when I had put it back together! Couldn't have done it without you.

  • @jaghond2
    @jaghond2 2 года назад +10

    Just came back here to comment that I managed to resurrect my long dead Homepod that I was going to throw away. I didn’t have the confidence to do this clean so I had a local repair shop attempt this. As suspected from the well described symptoms, it had the failed diode which was replaced, and the Homepod is back! Truly grateful to this video and channel!

    • @mcalann
      @mcalann 11 месяцев назад

      How much were you charged to fix it?

  • @johnsmith7244
    @johnsmith7244 11 месяцев назад +2

    Yesterday, the Christmas gift I bought for my wife many years ago - the first-generation HomePod - wouldn't turn on.
    My wife couldn't listen to music, a bit disappointed.
    Upon disassembling it, I discovered the Schottky diode on the power board, as mentioned by Nic, was faulty. However, the surface-mount component would take 7 days to arrive. Waiting wasn't an option. So, I spent five dollars on Amazon to buy 20 through-hole versions with the same 60V5A specifications. They arrived this afternoon. Using a hot air gun, I removed the faulty surface-mount one, soldered on the through-hole diode, and put it back together! It came back to life instantly! The material cost was only twenty-five cents, saving the HomePod! Ready for another 10 years!
    Now, my wife can enjoy music again, and all is well.
    THANK YOU SO MUCH! @NicsFix

  • @marty8332
    @marty8332 3 года назад +30

    Excellent video well orchestrated! Many just show how to disassemble something and then say the re-assembly is the opposite but there are many little intricacies involved in the re-assembly process as noted in this video. Well done! Thanks for taking the time to record, edit and post. I also like doing these sort of repairs and know the effort involved in making the video :-0 You took your time to adequately narrate and sped the video up at just the right times. High quality, clear and great angles made it easy to watch what you were doing. Five stars out of five!

    • @marty8332
      @marty8332 3 года назад

      How does one contact you?

    • @NicsFix
      @NicsFix  3 года назад

      @@marty8332 thank you so much for the compliments!! best way is on discord or in my server, discord.gg/track44 or add me @UnbendableStraw#4624

  • @thomasbellery
    @thomasbellery Год назад +2

    I usually don’t comment anything. But a huge thank you ! I got a defect HomePod for 20€ and repaired it thanks to you !

  • @SateeshDahdrai
    @SateeshDahdrai 2 года назад +6

    Best HomePod disassembly/repair video on youtube by far!!! Excellent job...Very professional!

  • @RicardoDawson
    @RicardoDawson Год назад +1

    Thanks so much Nick for this video! When my HomePod suddenly died a few months ago I was very disappointed, until I discovered your channel. Since I live in Argentina, it was not possible to send you the HomePod for repair (I would have been glad to do just that) but felt encouraged to try to resurrect it myself using your amazing tutorial. Long story short, my HomePod came back to life after the diode replacement, all thanks to your step-by-step guidance. Cheers!

  • @fenrir97043
    @fenrir97043 2 года назад +3

    A friends HomePod died and he gave it to me for free. Thanks so much for this guide! The repair worked like a charm. That ribbon cable being glued was so evil.

    • @ashr1881
      @ashr1881 Год назад

      Hi I have HomePod I can’t fix power not work, I send email on provide for fixed matter.

  • @saschadebie6656
    @saschadebie6656 2 года назад +4

    Perfect walk through. Fixed one of my HomePods just a few minutes ago. Works like a charm again. Without this video, something might definitely have been broken. I’ve sent a donation to support your great work.

    • @NicsFix
      @NicsFix  Год назад

      Thank you so much for your support!! Careful though, it can quickly become an addiction buying broken ones to fix up :)

  • @amitbraganza
    @amitbraganza 5 месяцев назад +1

    This is the most awesome video tutorial, hats off to you. I saw this and then gave my HomePod for repairs, it’s coming back today hopefully working like a charm

  • @jobvermeer2007
    @jobvermeer2007 Год назад +2

    Thanks for sharing this excellent walkthrough! I just finished fixing my Homepod (with a little help from a friend whom is beter at soldering) following your comprehensive video step-by-step. Big thanks and thumbs up!

  • @jonnitm7370
    @jonnitm7370 Год назад

    This was awesome. Just fixed a HomePod I bought off eBay that was dead on arrival. Got a full refund, then paid 80pence for the diode, replaced it and now it's back in business bustin' grooves. Thank you!

  • @hastingb
    @hastingb 3 года назад +4

    A+ repair job! In the past I never bothered replacing surface mount component due to the cost of the hot air soldering stations. But that was way back in the day. Now you got me thinking....

    • @NicsFix
      @NicsFix  2 года назад

      supposedly others have managed to replace the diode by using two soldering irons to heat up both ends of the diode, or a single iron with a tip the size of the diode. seems pretty risky to me with the other super tiny components right next to it but to each their own!

  • @bohampton456
    @bohampton456 2 года назад

    Thank you very much, I brought my HomePod back to life that died many months ago. It was the diode!

  • @yasmiellrodriguez248
    @yasmiellrodriguez248 2 года назад +3

    This is a spotless video and a very helpful and comprehensive tutorial that most be considered a jewel for anyone who has an Apple homepod that malfunctioned. Many thanks and hope this master of the homepod comes up with more helpful videos like this one. This is really appreciated. My hat is off for you!!

  • @erdepfel
    @erdepfel Год назад

    man you really have too much patience, really a great video about this repair, even the best video I found here on youtube about this repair, thanks for your kind showing

  • @TimothyBoudreaux
    @TimothyBoudreaux Год назад

    You make it look "too easy," but I know that's pretty hard. Nice video. Really appreciate it. I'm going to send mine to you asap.

  • @johnoneofmany
    @johnoneofmany 2 года назад +1

    Best video out there on this subject!
    Apple flat out refused to even look at my speaker. They said they don't repair them. they only offered to replace it at nearly full price!. My speaker was only 4 years old...
    Your website is a fantastic resource. I hope I can get mine working again. Unfortunately I've never done this sort of repair work so I'm a little worried. Fingers crossed.

  • @johnnysweetbeef
    @johnnysweetbeef 2 года назад

    Nic - hands-down the best instructional video ever. You really have a talent for this. My HomePod died a sudden and unexpected death. Sure enough, a shorted diode. The HomePod was the ‘slave’ on a stereo pair if that helps on your quest to understand why this happens. Anyhow, all repaired and I wouldn’t have even known where to start without your help. To anyone attempting to make the repair two things I learnt: the adhesive securing the main ribbon cable to the basket was murder, take your time! And the heat required to lift the faulty diode is phenomenal: so don’t be frightened to ramp-up the heat - you’ll need it.
    Nic - can’t thank you enough 🙂

  • @g.rogers9158
    @g.rogers9158 11 месяцев назад

    Great video. step by step instructions helped me pull down and reassemble. Thanks for your link and to Nanthan in Melbourne Australia who repaired the board for me.

  • @StanislawWozniak
    @StanislawWozniak 8 месяцев назад

    Thank you so much for the detailed instructions and awesome tutorial. My original HomePod died recently, and all the observations aligned with your guide. I managed to replace the diode (never done it before, so it was interesting), and now I have a working HomePod again. Apple wanted to charge me £260 for the replacement ;)
    I did have display issues while reassembling - the display worked fine when being tested "loose", but it started boot-looping when fully screwed in to the top - it was flaky to say the least, but eventually put it back together ensuring the final top 4 screws where not too tight.

  • @NotMexican
    @NotMexican 2 года назад +1

    Absolute S tier tutorial, went ahead and bought the stuff you recommended using your link. Genuinely, thank you, I did not want to go through the ifixit "teardown" where they destroy the speaker.

    • @iambujar
      @iambujar 2 года назад

      iFixit is just a group with a bunch of haters.

  • @dwdna
    @dwdna 4 месяца назад

    Thank you. Did not realize how much we used the HomePod until we had to go without for 2 months.

  • @randyborrero8604
    @randyborrero8604 2 года назад +1

    Awesome video... I know I can't do this work, but I now know it can be repair since these are now discontinued and only the small versions are for sale.

  • @byt3swap375
    @byt3swap375 2 года назад

    Thanks so much for this teardown / reassembly guide. Just got #1 of a handful of broken HomePods I ordered working!

  • @applepietech
    @applepietech Год назад

    Thanks a lot! Took apart and fixed my HomePod in no time thanks to You!

  • @norbertovianaeloy
    @norbertovianaeloy 2 года назад

    Amazing work on filming and explaining the hole process.
    My HomePod just got the same problem, let’s just pray that someone can repair it like you did.

  • @scottv1300
    @scottv1300 Год назад

    What a complete and well thought out demonstration- thank you so much! I'm going to have to give it a try on
    my dead HomePod.

  • @seanm.6865
    @seanm.6865 Год назад

    awesome explanation Nic, greatly appreciated! I followed the directions and appreciate your input of rework temperature, I maxxed it at 500c for 30-45 seconds which did the trick. Put it all back and its working perfectly

  • @mangs90
    @mangs90 2 года назад +2

    Awesome Best DIY video I have ever watched, Great talent, tip my hat to you, Sir. Your D man. Thanks a lot for sharing.

  • @landman214
    @landman214 2 года назад

    HI There, don't want to throw mine away, never changed a diode but im quite good at most things, will give it a go. Great vid

  • @shinjiikarir
    @shinjiikarir 2 года назад

    One of the best disassembly tutorials I've ever seen. and ive seen a lot! Thank you so much!

    • @shinjiikarir
      @shinjiikarir 2 года назад

      I tried it myself today, since i am not very patient i broke the lid a little bit, everything else was really easy. Thank you!

    • @NicsFix
      @NicsFix  2 года назад

      adds character :) happy to hear you git it working again!!

  • @adnansafdar5663
    @adnansafdar5663 2 года назад +1

    One of the best videos I have seen on the HomePod tear down. You manage it without destroying the device which is commendable. I have a unique situation with my HomePod. There is absolutely no bass. It happened a few months ago. Any suggestions?

    • @NicsFix
      @NicsFix  2 года назад

      I would check that your subwoofer is still good somehow, maybe using an external amplifier or another homepod for testing parts. If the woofer is still good, it's likely the amplifier IC that drives the subwoofer which I made a video showing how to replace! The video shows a no power diode repair and the amp IC repair but just ignore the diode parts: ruclips.net/video/OvHope_C_lc/видео.html

  • @NicsFix
    @NicsFix  2 года назад +4

    ouitmenick made a great suggestion; when prying the top basket off the speaker, pry against the top of the subwoofer screws! this way you can avoid cosmetic scratches on the woofer. you may bend the subwoofer screws trying this but they're easy to bend back...YMMV!
    before prying the basket off the subwoofer, drip 99% alcohol inside the perimeter to weaken the adhesive!
    check out my new uploads where I show how to repair dc offset / death farts / crackling or popping bass, replace your mesh, and even repair a no-power homepod that WASN'T caused by this diode!

    • @TechDraX
      @TechDraX 2 года назад

      really love your videos, I love the homepods especially in stereo mode and is sad to see they discontinued it. Now thanks of you we finally also gained the ability to last the product at least for a very long time to counter the most happening issues it has. I don’t know why apple put a cheap diode component in such an expensive product anyways. Profit was bigger than quality I guess.. Thanks a lot for your videos looking forward of more content!

    • @NicsFix
      @NicsFix  2 года назад

      @@TechDraX who knows! the trend I've noticed so far with these diode failures is interesting and not necessarily indicative of apple just cheaping out on this diode. All of the diodes across all homepods have the same model number. But, so far, only diodes with a later date code on them have failed. I have not yet replaced any diodes from earlier date codes. With this trend I'm guessing there was just a bad batch of diodes later on, or, the later batch is just more prone to overheating and shorting out.

  • @bruhgamerwolf7936
    @bruhgamerwolf7936 3 месяца назад

    Amazing tutorial managed to fix a HomePod that I found on the street on garbage day.

  • @jaked5474
    @jaked5474 Месяц назад

    Mad respect for the proper use of the word finagle.

  • @kananeesh7900
    @kananeesh7900 2 года назад

    Man, my HomePod stopped working yesterday, won’t turn on. Wish there’s was a shop around that would accept these things for the fix you just showed.

  • @ColemanRasof
    @ColemanRasof 5 месяцев назад

    Thanks!

    • @ColemanRasof
      @ColemanRasof 5 месяцев назад

      Hey wanted to let you know this worked for me! Thank you for sharing 🎉

    • @NicsFix
      @NicsFix  5 месяцев назад +1

      YESSSS!!! Thank you for letting us know!

  • @joshcliffejones
    @joshcliffejones 2 года назад +1

    ABSOLUTELY FANTASTIC! Thank you SO much my friend this has saved me big! I bought a replacement diode (different to the one you linked due to being in the UK, but same specs as original), followed your guide and sure enough that has resolved the issue and resurrected my lifeless HomePod! :D Shame that this appears to be such a common issue on these devices, but i guess they unfortunately werent around long enough before Apple killed them for them to start failing whilst in service :( At least i now know what to expect when another one of mine dies!

    • @baztherat253
      @baztherat253 2 года назад

      Hi Josh. Same problem. Would you mind sending me the link for the uk spec diode? Can’t find. Cheers

    • @paulcook7905
      @paulcook7905 9 месяцев назад +1

      I am also in the UK, do you have the diode details please?

  • @johnschmitt9158
    @johnschmitt9158 2 года назад

    I'm very impressed by your work on the HomePod. Well done.

  • @Jushwa
    @Jushwa 2 года назад

    You rock dude. If you ever solve the dreaded flashing HomePod mine is ready lol. It was so sad near the end it would come back to life spontaneously after an unplug but now it’s perma fried. I was on 14.3 beta when mine died. I tried unplugging it for a year and plugging it in but she’s cooked. Kind of annoying these things are so unreliable compared to an Alexa which is like a tenth of the cost but after seeing you tear down down just like the internals of any other apple product I now see why it’s more costly.

    • @NicsFix
      @NicsFix  2 года назад +1

      These things cost around $200-250 for apple to manufacture! Pretty insane but in my opinion to this day still justified and an unbeatable experience that they still offer. My fingers are crossed for a solution to bricked ones soon, it's the last hurdle we have before we've solved it all!

  • @piterqh
    @piterqh 7 месяцев назад

    Very good job, perfect explanation, I want to build my workplace like yours but I can’t find the apple pc cover for use the hot-gun and don’t damage the table😅, thanks again

  • @gauravagarwal4949
    @gauravagarwal4949 10 месяцев назад

    Hi Nic
    Hands down the best tutorial
    I came across your video after I developed fault with my HomePod
    I accidentally left my HomePod upside down and after that when I tried playing song on it I started experiencing issue with bass on high volumes. It also feels like there is some loose screw dancing in the HomePod
    Any suggestions
    Shall be greatfull to you

  • @soapisgood
    @soapisgood Год назад

    Thank you so much! My HomePod is good as new.
    You can add another 1748K to your list!

  • @the.real.Black306
    @the.real.Black306 Год назад

    Thanks for the video! Just fixed my HomePod with this issue.

  • @richknowles72
    @richknowles72 2 года назад

    Excellent video!!! Thank you. I should have looked it up before I got into repairing mine. I'll get some parts and resurrect it. Thank you!!

  • @nikpester
    @nikpester Год назад

    Great video. I most certainly wouldn't have tried to repair my dead Homepod 1 without the excellent instruction. Thanks very much Nic. These things are a right pain to get apart, but most satisfying to repair!

  • @marioamazing3274
    @marioamazing3274 9 месяцев назад

    Nic's Fix, thank for this awesome guide!
    Maybe you know why after repairing HomePod powers for 4 sec and after that turn off?

  • @dreamstate07
    @dreamstate07 2 года назад

    Thank you so much for putting such comprehensive videos together. This definitely gave the confidence to try and repair our blown-diode HomePod.
    While we replaced the diode and managed to get power back on, it still behaves a little wonky. When the sub hits a high volume, the whole HomePod loses power and resets. A friend who helped with the soldering repair mentioned that occasionally when a diode shorts out, it may take down nearby components (in this case, they suggested that the IC immediately adjacent to the diode may have taken some damage). Have you ever replaced other components on the amplifier board, or run into a situation like this post-repair?
    Thankfully the IC in question is apparently readily available -- a TI TPS5450 ... so I was thinking of repairs round two ...

    • @NicsFix
      @NicsFix  2 года назад +1

      I haven't experienced what you're describing after repairs though what your friend is saying makes sense. I would also be curious if you have any dc offset: nicsfix.com/#popping

    • @dreamstate07
      @dreamstate07 2 года назад

      @@NicsFix We'll take it apart and let you know the findings. Just happy to provide more data points that may result in more repaired 'pods.

    • @jackgerberuae
      @jackgerberuae Год назад

      @@dreamstate07 any feedback on your second repair?

    • @dreamstate07
      @dreamstate07 Год назад

      ​@@jackgerberuae Alas, we think we have a damaged logic board. It got stuck in a few reboot loops, and when iOS tries to push an update to the HomePod, it would download the 0.5GB update, reset, and start the download again. This is in addition to the points mentioned in my original comment above.
      So unfortunately, we've given up on this one. :(
      I'm eyeing one of the new 2nd gen HomePods ...

    • @jackgerberuae
      @jackgerberuae Год назад

      @@dreamstate07 thank you for the update. I will be able to strip mine, but that is where it will end 🤣🤣🤣
      I saw Marques Brownlee reviewing the HP2 just before watching this video - which reminded me of mine. Have a look, the review is not very positive

  • @ge-kas122
    @ge-kas122 25 дней назад

    Thumps up!!!! Best video ever... Thanks for sharing

  • @UpandGoOut
    @UpandGoOut 2 года назад +1

    Hi, Thanks for this tutorial on this fix :-) One question what kind of grease, flux or whatever is it you dip the diode in before soldering?

    • @NicsFix
      @NicsFix  2 года назад +2

      I lost the lid for that a long time ago and it was an old jar I borrowed from work so I am not sure :( but I've been using Chipquik NC191 in all of my repairs now

  • @ledhunters
    @ledhunters 2 года назад +1

    Hi, is there a replacement power plug/cord for this homepod, but cheap version, not the 15$+ one! thanks

    • @NicsFix
      @NicsFix  2 года назад

      Hiya! I've bought a few of the ~$15 power cables off eBay before. They have all been fine and compare to the original ones. not sure if there's any cheaper options!

  • @StukaUK
    @StukaUK 2 года назад

    Well done.
    I’m sure you make it look easier than it is. So I might not attempt it still, but first I need to see if that diode is easily available. Then I’ll have a think about it.
    Edit.. thanks… I see you have a source link so great, but now I realise I don’t have the right tools. I have a standard soldering iron. I’m not familiar with anything else.

    • @NicsFix
      @NicsFix  2 года назад

      You miiiiight be able to wick all the solder out from under the diode via it's pins, I'm not sure. Also not sure if you can adequately resolder a new one on all with just an iron, but I've read stories from others who have managed. If you're at all into soldering, even a cheap $50-75 hot air station goes a long way though!

  • @SteveBattye
    @SteveBattye 5 месяцев назад

    Hi Nic, I have 2 and I’m convinced they need new diode, i.e. they do notbpowerup but get warm around the power supply. I have the replacement parts and a Fixit kit but, having seen the effort involved, plus the likelihood of me losing a couple of fingers, I feel my place is in my garage, fixing my old Triumph bikes.
    Cut to the chase, I’m in Scotland, how many limbs do I trade … and … naturally, can you get them back to me before I notice that they’re missing?
    RSVP and I’ll forward the video of me smashing a number of piggy banks,
    Steve. 😜

    • @SteveBattye
      @SteveBattye 5 месяцев назад

      Sheesh, what’s keeping you; you don’t sleep do you?
      2:24 here, perhaps I should do this same.

    • @NicsFix
      @NicsFix  4 месяца назад

      @@SteveBattye Hey mate! I must say this is one of the most amusing comments I've had in a while! As you guessed, shipping will suck between you and I, it won't be cheap (about $75 USD) or fast, or reliable
      The good news is there are three different folks in the UK offering repairs too! I have them listed on my website nicsfix.com , under the Mail-In Repair section , just keep scrolling :)
      Let me know if there's anything I can help with!

  • @DaviAreias
    @DaviAreias 2 года назад

    I tried replacing the small caps myself, but it's super hard. I don't advise newbies to do it.

  • @goodelectronics4170
    @goodelectronics4170 8 месяцев назад

    Thank you for this. I have mine same issue as well. What’s the diode number pls so I can order now. Thanks.

  • @PavloVelykyi
    @PavloVelykyi 5 месяцев назад

    Thanks a to for this tutorial, had the same issue, done same steps and it is working. Amazing 🎉🎉🎉🎉 and I have enjoyed it

  • @arashrkarimi
    @arashrkarimi 6 месяцев назад

    did you apply glue when putting back the top (touch disc with plus and minus)?

  • @DavidRodriguez-zd4si
    @DavidRodriguez-zd4si 10 месяцев назад

    Una maravilla de tutorial, realmente me sirvió como instructivo para poder arreglar uno de mis homepods. Muchas pero muchas gracias.

  • @unyhrc
    @unyhrc 2 года назад

    Impresionante vídeo, la verdad todo muy claro y fácil, muuucchhhass gracias por tu enorme trabajo un abrazo! 👍👍

  • @SteveWaller-y7y
    @SteveWaller-y7y Год назад

    How tight do you put he sub screws in, I have repaired mine, thanks to you, but I now have a vibration noise on some bass notes?

    • @NicsFix
      @NicsFix  Год назад

      They should be firmly tightened, but not so much that you're squishing the gasket. A little squish is good. More likely you have a loose / missing gasket somewhere

  • @dannymulligan7646
    @dannymulligan7646 8 месяцев назад

    Thanks for this video, Apple HomePod is working again.

  • @iMackJudah
    @iMackJudah 2 месяца назад

    Hello. I have a 1st gen HomePod I purchased from Best Buy in 2021 well taken care of never been dropped, and no water damage.
    I recently did the iOS 18.1 update, the next day it won’t power on at all now smh. I’ve tried unplugging and plugging it back up numbers of times, but nothing! How can I get my HomePod to you to fix it?

  • @adetoye50
    @adetoye50 3 года назад

    Excellent job done here, now I can believe that the future of the Original HomePod is guaranteed just like the way iPod Classics continue to flourish after  KILLED the great device.
    Thanks for this video, do you advise that we should be switching off the HomePod from the power? At the onset of this videos, you said because the HomePod is plugged in permanently that could be why the DIODE is burning off. Thanks and looking forward towards another wonderful videos.

  • @connorhornung
    @connorhornung 6 месяцев назад

    Damn, I can only imagine what you charge to repair one of these. Probably cheaper to buy a new one! great clean work though, I’m very impressed that you have gone into that rabbit hole 13 times and been successful. Also never realized how big the magnet on the subwoofer was, and how many caps were inside one of these. Mine has been dead for a few months.

    • @NicsFix
      @NicsFix  6 месяцев назад

      I’ve fixed a few thousand of these now and live-stream most of them here! I’ve got current prices and info on my website at nicsfix.com

  • @JohanFroloff81
    @JohanFroloff81 7 месяцев назад

    I somehow managed to put the top ribboncable in backwords. My thermal camera. Measured 81c coming from the little led thing on the top. I quickly flipped it around. Now it measures 41c and still doesn’t turn on. Any advice would be nice.

  • @johnvargo8050
    @johnvargo8050 Год назад

    Thanks for the video. I had a homepod with the same issue, the warmth on the side when plugged in but otherwise dead. I replaced the diode per your instructions. Now, when I power it on, nothing. Still dead, but it no longer gets warm on the side. Any thoughts on what it might be? Thanks in advance.

    • @NicsFix
      @NicsFix  Год назад +2

      Most of the time it's something you might have damaged along the way like a ribbon cable. Or you just don't have one of the ribbon cables fully reinserted or correctly locked. nicsfix.com/#goofball

    • @johnvargo8050
      @johnvargo8050 Год назад

      @@NicsFix Thanks for the reply, and the link! I disassembled, re-soldered, and re-assembled and still dead. Time to throw in the towel, but thanks for all the great information!

    • @NicsFix
      @NicsFix  Год назад

      @@johnvargo8050 are you by chance in the US? I would be willing to help you out if you can send it in!

  • @serge405
    @serge405 2 года назад

    Excellent thank you very much for sharing this video your description is perfect and in the detail, the only thing I would like to ask you please? ¿What is the faulty part's name? DIode? and the value in amps or any other detail I may need to know to get another one. Would you mind giving me the full details of that diode or part that you mentioned? and if possible where I may order or buy it? please? I will appreciate your kind reply thank you very much regards from Melbourne Australia.

    • @NicsFix
      @NicsFix  2 года назад

      I have the schottky barrier diode part number, and one place to buy it as an example in the video description! Thank you

  • @diannetorres308
    @diannetorres308 2 года назад

    hello, thank you so much for this video. I believe my HomePod is suffering from the issue mentioned. where do i purchase replacement Diodes?

    • @NicsFix
      @NicsFix  2 года назад

      Part number for diode is PDS560-13. Search on google for it and you'll find plenty of places. I prefer digikey and mouser

  • @tonyjames327
    @tonyjames327 Год назад

    thanks mate.
    Saved me a ton of money.
    Cheers big ears..

  • @shenye3274
    @shenye3274 6 месяцев назад

    great job, and great video for next 5years

  • @tundephiliptoye6833
    @tundephiliptoye6833 2 года назад

    Excellent video . My question is a friend of mine brought in some used homepods from the states, and most of them are not connecting. It would not even reset. Here in Lagos, Nigeria we do not have Apple support. Anything that can help him is welcome

    • @NicsFix
      @NicsFix  2 года назад

      Hmm are they just booting up to flashing volume lights? If so they would need a logic board swap. Sadly I don't even have any good logic boards to do these specific repairs and no one has figured out how to de-brick them. But if you can find other broken homepods that, say, have sound or power issues, they likely still have good logic boards to swap with then factory reset.

  • @danielmccafferty2184
    @danielmccafferty2184 2 года назад

    Would it make sense to replace the diode with a higher power diode? A 70V 6 A for example. (Great video by the way)

  • @WayneMcCormick
    @WayneMcCormick 8 месяцев назад

    I'm having this same issue with a Gen 2 HomePod, it won't power on, won't join wifi. Will this fix work for it as well? Are the internals close enough?

  • @יואבמשרתי
    @יואבמשרתי 2 года назад

    Great video! Loved watching it! I've got a similar problem with the homepod mini. Mainly doesn't respond when reconnected once disconnected to power - then if left connected can randomly turn on. Basically turns on on its own will. Any thoughts?

    • @NicsFix
      @NicsFix  2 года назад

      I haven't had my hands on any Minis yet...can you give the power cable and connector a good wiggle to see if it's perhaps broken inside? I'm guessing you've also tried another power supply too. This doesn't really sound like an internal hardware failure to me yet if it sometimes powers on and sometimes doesn't, but I'm not sure.

  • @bhupeshmishra8968
    @bhupeshmishra8968 2 года назад

    Excellent video!
    But I’ve partly snapped the longest/3 split ribbon cable during the flat-head manoeuvre. Any chance of revival?

    • @NicsFix
      @NicsFix  2 года назад +1

      Sadly Apple won't give us replacements :( only way to get more is from another homepod. It's possible you only damaged noncritical lines but it's not worth the risk trying it as you could end up shorting and wrecking both the amp board and logic board, ugh! We all need to bug Apple to add homepod parts to self service repair!

  • @bluecoat9429
    @bluecoat9429 2 года назад

    Hey man, great tutorial. I got one problem after changing the diodo, the chip to the left of the diodo shown in the video got burnt as well,, the 8pin chip,, and every letter on it are screwed... i have no idea what chip is it,, could you please be so kind of telling me what chip is that? thank you in advanced.

    • @NicsFix
      @NicsFix  2 года назад

      That is a Texas Instruments TPS54560 dc to dc step down converter. It's been superceded by TPS54560B which will also work as a replacement!

    • @bluecoat9429
      @bluecoat9429 2 года назад

      @@NicsFix Thank you so mucho for the quick reply! cheers!

  • @davidwardle6712
    @davidwardle6712 2 года назад

    Awesome! Thanks so much for posting. My HomePod crapped out earlier this week and I was very chocked. Now I at least have an option to attempt a fix as I had no desire to give up or replace my HomePod if I could help it. What part info can you share regarding that diode so I can purchase locally or order once? Again, much thanks.

    • @NicsFix
      @NicsFix  2 года назад +2

      It's a surface mount 60v 5a schottky barrier diode, I replace it with part number "PDS560-13" which I get from digikey here (available at a bunch of online component stores): www.digikey.com/en/products/detail/PDS560-13/PDS560DICT-ND/776779?so=73342686

  • @redmohawkgeoff
    @redmohawkgeoff 2 года назад

    Have you ever encountered a very stubborn diode that doesn’t want to come off the board? Using hot air soldering iron and tried regular. Won’t budge.

    • @NicsFix
      @NicsFix  2 года назад +1

      Yeah they can sometimes put up a fight. You're fighting against the board acting as a big heatsink, too. Make sure your hot air is turned up to 500c, ~80% airflow, and preheat the backside of that area of the board for ~15 seconds, then flip it back around and go straight for the diode until it comes off.

    • @redmohawkgeoff
      @redmohawkgeoff 2 года назад +1

      @@NicsFix hey that did the trick! Thanks for the help. Got it all back together and working! Awesome video👍🏻

  • @Bodalbyte
    @Bodalbyte 2 года назад

    Hi Nick, very nice video. I think I have similar issue of not powering on at all. Can you repair it? How much will you charge?

    • @NicsFix
      @NicsFix  2 года назад

      Hi there! Currently the no power repairs are $60 plus return shipping of your choice. Feel free to shoot me an email at nic@nicsfix.com if you have any questions or want to send it in!

  • @philipkitching1340
    @philipkitching1340 2 года назад

    That very last step when you place the top cover back on... Is that glued on? I see you moving it around to center and seat it ... are there catches in there or is it glue?

    • @NicsFix
      @NicsFix  2 года назад

      Yes that uses adhesive to stick on, no alignment notches or anything, I'm just trying to line up the volume buttons under the top cover to the volume cutouts on the layer below it before pressing it down to fully stick back in place.. If you don't touch the adhesive with greasy fingers and cut it clean enough when you first remove the top cover, it's usually good enough to re-use when putting back together. We've gotten about 50-75 homepods sent in and shipped back out by now for repairs doing this and I haven't heard any complaints or issues of them coming loose so it seems to be working well.

  • @demlotcrew
    @demlotcrew Год назад

    How does the top touch cover adhere back on if the foam tape is cut?

    • @NicsFix
      @NicsFix  Год назад

      You can gently re-heat both sides of the adhesive to re-use it! If its no longer sticky, some rubbing alcohol can clean it up, too. I don't advise using new adhesive as that will make taking it apart again in the future unnessecarily difficult

  • @keaganwright124
    @keaganwright124 2 года назад

    Is it possible to replace the diode with just a variable temp soldering iron? Or do you need the hot air station?

    • @NicsFix
      @NicsFix  2 года назад

      There's a large pad on the bottom of the diode and the board will also suck a lot of the heat up, so a hot air station will make quick and easy work out of it. I've heard others successfully using two soldering irons on each side or one large one big enough to cover the whole diode but sounds tedious

  • @_c8k0g8_
    @_c8k0g8_ Год назад

    Mahalo!🤙🏽

  • @johnwhittaker8992
    @johnwhittaker8992 2 года назад

    Hi Thanks For Vid What Is The Air Flow Set To I Have Same Station you Have From amazon

    • @NicsFix
      @NicsFix  2 года назад

      Its at about 75-80% airflow!

    • @johnwhittaker8992
      @johnwhittaker8992 2 года назад

      @@NicsFix Thanks Ive Sent You A Email Abput A repair Job If you Can Do Im In UK

  • @Dr.Marcos
    @Dr.Marcos 2 года назад

    The speaker in self is a sealed enclosure, right? If I put some dust cover to prevent this insane dirt in the woofer (mine is white too) the electronics won't be hotter?

    • @NicsFix
      @NicsFix  2 года назад +1

      Im not sure I understand how you will do this, but it will almost certainly run hotter. I wouldn't be concerned with altering a HomePod to prevent dust anyways, instead you can simply blow compressed air through the mesh and giving the top touch cover a quick wipe every time you feel like cleaning them. I use a plug in electric air duster to save $ on buying cans of air and hit all of my homepods about once a month

    • @Dr.Marcos
      @Dr.Marcos 2 года назад

      ​@@NicsFix Thanks. I already buy dust covers named "TXEsign Elastic Anti Dust Cover for HomePod", recommended by iMore. In the article they says that not interfere with the sound, but nothing about thermals. My window is up front a traffic street and a lot of dust enter in my bedroom. I vaccum clean the floor 2 times per week and remove the dust from the forniture almost every day. White things tend to turn gray.

    • @NicsFix
      @NicsFix  2 года назад +1

      @@Dr.Marcos I see, those look pretty safe to use. I can't imagine it being more than a negligible impact on sound and heat dissipation, especially since it leaves the top exposed and it looks pretty breathable

  • @BenStockdaleAU
    @BenStockdaleAU 2 года назад

    What happens if you don’t avoid the pcb plastic layer problem? I thought I had it right but only got the top layer off? Is it recoverable?

    • @NicsFix
      @NicsFix  2 года назад +1

      The plastic is removable but I generally just don't recommend it because you can knock off the ambient light sensor that's on that side of the PCB, and you can also scratch the PCB and damage traces. If you haven't damaged the PCB you can simply reinstall the plastic layer. If you accidentally knocked off the ambient light sensor, the display will still work fine but at 100% brightness all the time.

  • @MartinElbl
    @MartinElbl Год назад

    Hey:) thanks for this video:) what is the recomanded temperature and airflow on heat gun for this little shottky?:D Thx in advice:))

    • @NicsFix
      @NicsFix  Год назад +1

      If you don't pre-heat the board (most people don't) you'll need around 400-500c at ~80% airflow. This is with my cheap $60 hot air station fwiw.

    • @martinelbl9691
      @martinelbl9691 Год назад

      @@NicsFix thanks for quick reply! Will try:)

    • @MartinElbl
      @MartinElbl Год назад

      @@NicsFix Worked like a charm:))) THANKS! is it possible to replace that PDS560-13 /w something simillar?

    • @martinelbl9691
      @martinelbl9691 Год назад

      @@NicsFix thanks a lot, since I saw your video I have repaired 3 homepods:)

    • @idrjohn
      @idrjohn 11 месяцев назад

      I wish spent a bit on removing the diode, i've been at 500c 80% airflow and it's not budging@@NicsFix

  • @martsn54
    @martsn54 3 года назад +2

    Top Work !!!

  • @delerium974
    @delerium974 2 года назад

    Hello. What chip is next to the schottky diode? I think mine is burnt....Thank you!

    • @NicsFix
      @NicsFix  2 года назад

      Sorry for the delay!! If you havent found it by now that is the TPS54560 step down converter. It's no longer in production and replaced by TPS54560B

    • @delerium974
      @delerium974 2 года назад

      @@NicsFix Thank you 🙏

  • @p3rrypm
    @p3rrypm 3 года назад +1

    After watching this, I'll just buy a new Sonos, forget all this! How much do you sell the repaired units for? I would love a second one, but some people would rather have them sit unsold with crazy high prices, than sell them for a little bit less.

    • @NicsFix
      @NicsFix  3 года назад +4

      It should be known that replacing this diode doesn't fix any of the popping issues. There are three popping issues I'm tracking:
      1) Loud Pop and Restart, associated with a panic log in your HomePod Analytics. Apple says this is fixed in the upcoming 15.3 release. (UPDATE: Software popping is fixed in 15.3!)
      2) Loud pop and restart, no panic logs. This is more likely a failing amplifier IC, a custom part made only for apple's homepods that we cannot get. This is a sign of iminent failure. (UPDATE: Not the amp IC, but failing filtering capacitors. I've also found two options for replacement amp IC chips)
      3) Subtle click / pop every ~10 minutes or as the homepod goes in and out of standby. This is also caused by the amp IC, when it turns on it sends dc to the woofer which you hear as a pop. (UPDATE: As stated above, not the amp ic!!)
      EDIT: Issues 2 and 3 I have found repairs for! They are not caused by a faulty amp IC, but in fact failing capacitors! Check my channel for new repair videos~

    • @Gleeleeglee
      @Gleeleeglee 2 года назад

      @@NicsFix May I ask how long your work is warranted for? Thanks.

    • @NicsFix
      @NicsFix  2 года назад

      @@Gleeleeglee I give a 12-month warranty on all of my work and parts :)

  • @waldemarmaerz64
    @waldemarmaerz64 2 года назад

    Hi, do you have also a solution for HomePod which led lights on the top aren’t showing up? Everything works except the Siri and + and - light. Touch is working fine.. I have updated and reset the device. But that didn’t helped.

    • @NicsFix
      @NicsFix  2 года назад

      Both the touch and display are on the same PCB and use the same ribbon cable to connect to the logic board, so, if touch works, I would guess the cable and connector are likely still fine, too. I've not yet seen a display simply stop working before on a homepod but I would hazard a guess that's what is needed. Hard to know without taking it apart and swapping around parts!
      Also curious if you've tried both factory reset methods, both from the home app and using the red spinning circle method

    • @waldemarmaerz64
      @waldemarmaerz64 2 года назад

      @@NicsFix thank you for your assessments. I tried also both reset methods. But the result was the same. No led lights. I think I will try to look into the HomePod and check and switch some parts..

  • @davidwardle6712
    @davidwardle6712 2 года назад

    Also wondering what temp you ran the reworking station at? I am not having any luck in removing the diode but don’t want to prematurely bump up the temperature

    • @NicsFix
      @NicsFix  2 года назад +3

      I was exactly the same at first, but I found on my cheap little station that it works best (and only works at all) when I max it out at 500c, then hold the hot air about half to one inch away for about 30-45 seconds until the solder has melted and I can pull the diode off. The amp board is acting as a heat sink and taking away a lot of heat.

    • @davidwardle6712
      @davidwardle6712 2 года назад

      @@NicsFix Thanks for the info. Much appreciated. I am a complete noob when it comes to soldering but your video has inspired me.

    • @NicsFix
      @NicsFix  2 года назад +2

      @@davidwardle6712 That's the goal! I strongly suggest also watching "Basic Soldering Lesson 1 - "Solder & Flux"" by the paceworldwide channel if you're looking to learn. I would contribute the majority of my fundamental understanding and success with soldering to that series.

  • @goodelectronics4170
    @goodelectronics4170 5 месяцев назад

    Is it possible that no power caused by logic board?

  • @jonstew1455
    @jonstew1455 3 года назад +1

    Great video, it looks like you have had a lot of experience with repairing these HomePods. It appears you even repair these for other people as well on occasion. I have one that will not power on; It was sitting on the kitchen counter and got knocked off (oops). It has no physical damage on the outside and was not on when this event happened, Do you think there could be a loose connection inside preventing it from powering on? I tried to contact you through Discord but couldn't really figure out what to do.

    • @NicsFix
      @NicsFix  3 года назад +1

      Let me hop on my discord and we'll see what's up

    • @adetoye50
      @adetoye50 3 года назад

      @@NicsFix
      Me too, joined you on discord, but I can't get in touch with you @AdminTech

    • @NicsFix
      @NicsFix  3 года назад +1

      @@adetoye50 Ah I see now, my nickname on discord is different than youtube. I'll ping ya

    • @jackgerberuae
      @jackgerberuae Год назад

      I have a similar situation with my pod. It fell 😢.
      Did you manage to get yours fixed, and how please?

  • @davidwardle6712
    @davidwardle6712 2 года назад

    Have you ever reapplied the silicone adhesive?

    • @NicsFix
      @NicsFix  2 года назад

      I haven't ever yet, it doesn't seem necessary in my testing, but if someone were to request it I would happily oblige

  • @dimartinpy
    @dimartinpy 2 года назад

    good afternoon, could you tell me where to buy the motherboard you are talking about in minute 6? I have that problem of the intermittent lights of the volume

    • @NicsFix
      @NicsFix  2 года назад +1

      There's nowhere I know of you can buy these, aside from buying broken homepods and harvesting the parts from them, ideally ones that have "no power" or other issues where you may be able to deduce the logic board may still be fine

    • @dimartinpy
      @dimartinpy 2 года назад

      @@NicsFix Oh my God, then it's even more difficult, I'm in South America and here it's much more difficult to get these parts. thank you very much for your prompt response

    • @Lefarr
      @Lefarr 2 года назад +1

      @@dimartinpy where in South America are you? Do you want to sell your HomePod? I need some the amplifier board.

    • @dimartinpy
      @dimartinpy 2 года назад

      @@Lefarr I'm from Paraguay, but I don't know if I would have a way to send the homepod

    • @Lefarr
      @Lefarr 2 года назад

      @@dimartinpy where in Paraguay? I could meet you in Asunción if you near by.

  • @hammer2302
    @hammer2302 Год назад

    I have a broken Homepod, when I brought it to a repair shop it said it’s SMPS stopped working. Any idea what the issue is?

    • @NicsFix
      @NicsFix  Год назад

      SMPS sounds like they're saying the power supply is dead. It's impossible to tell what's wrong with a no-power homepod without disassembling it for diagnosis, but you can GUESS what's wrong with it by looking at it's power draw. Zero watts of power draw is usually a blown fuse on the power supply. 1-2 watts draw is usually a short on logic board. 3-7 watts draw is the MOST COMMON with no power pods and is caused by the same shorted diode on the amp. At least 9 out of 10 no power homepods are the same dead diode, NOT a power supply or logic board issue. nicsfix.com/#commonissues

    • @hammer2302
      @hammer2302 Год назад

      @@NicsFix Thanks a lot for the response. It seems to me that the fuse has blown, I’m not sure as I can’t check the power draw for my HomePod. Can I use any 3.15 AH Fuse to replace the one on my HomePod? Or should I use the exact same fuse. I don’t have much idea about these things.

    • @NicsFix
      @NicsFix  Год назад

      @@hammer2302 I'd suggest replacing with "T3.15AH250V" It is specifically designed to fail under specific conditions, you'd want to stick to it for the best protection

  • @HR135.
    @HR135. Год назад

    Thanku you bro I got my home pod repair done