Pata hoga to explain karega, book se padke yaha likh raha hai, Round relevant indication ke dimension ko hi acceptance criteria bata raha hai, achhe se pad le pahle
I have a doubt sir., We have separate sections for NDT ie) ASME section v for non destructive testing., Then why should we need to refer ASME sec viii div i?., I mean how we come to the conclusion that we have to refer sec viii rather than sec v.,
Sec V is only for NDT and it gives a general guideline for NDT (not acceptance criteria). However, Sec VIII is exclusively for pressure vessel and it contains everything pertaining to pressure vessel including the acceptance and rejection.
Acceptance criteria is always determined by the applicable code of construction. It can not be generalized. Thank you. Please visit my website www.weldingandndt.com/
As per ASME BPVC SEC VIII DIV 1 MANDATORY APPENDIX 4 (4-3). The indication which is more the (t/10) for t less than 3mm, 0.39mm for t between 3mm to 6mm, 0.79mm for t between 6mm to 50mm and 1.58mm for t more than 50mm will be considered as a relevant indication. Below to this dimension will not be considered as a relevant indication. The acceptance criteria for a relevant indication is (t/4) for a random indication and (t/3) for an isolated indication.
Deposit weld material You wrote T, actually it is t. ' T ' we use as plate/pipe thinkness ' t ' we use as weld deposit thinkness. If anything wrong, please educate me. Thank you.
Sir, Kisi bhi 2material ko jab ham welding karate hai to usko welding karane me jitni electrode lagati hai usaka calculation karne ka tarika kya hai. Kripya batane ki kripa kare. Aap ka channel bahut hi achha hai ha pcbc ke liye. Thanks
your information about rejection of rounded indication is not correct you tell about non relevant indication we have to check only relevant indication by the way nice work
![[English] Acceptance criteria as per ASME section VIII Div 1](http://i.ytimg.com/vi/iazeV7_ABIM/mqdefault.jpg)
![[English] Acceptance criteria as per ASME section VIII Div 1](/img/tr.png)
During explanation of rounded indications that was relevant indication of according to the thickness. That's not size of rejected indication.
Sir, thanks for valuable knowledge. You are doing great work.
While, for rounded indications, that is relevant indication not reject indication.
Sir please explain mandatory apendix 4 of section-8 as per given in book. As chart mention isolated, random, cluster etc should be explained by you.
Rounded indication shown is relevant indication not maximum to accept
Yes
Thankyou sir,please make one video about welding map
Thanks it helped ,me now i understand it better 😎🤞
Thank you. Please join my channel to support my initiative. Joining link:
ruclips.net/channel/UCH7nXSievFlbRKzKzEySbkwjoin
Sir please explain elongated indication rounded or liner
Pata hoga to explain karega, book se padke yaha likh raha hai,
Round relevant indication ke dimension ko hi acceptance criteria bata raha hai, achhe se pad le pahle
Rounted indication How to calculate please immediately uptate in sir.right maltiple calculation.
Very Nice Explaination Sir
Thank you. Please visit my website www.weldingandndt.com/
Yes sure sir... All your videos are very useful and help ful for us .....
IQI is mandatory for RT filim interpretation
What is 6L
Sir u have explained acceptance criteria for radiographic testing as per ASME SEC Viii and IX. How to decide which criteria to follow?
Can you explain slag elongated and ISI slag difference in brief
Thanks a lot. Please visit my website www.weldingandndt.com/
Sir.. Please upload vedio acceptance criteria of ASME B31.3 piping.
Please sir acceptance criteria for tank API 650
Sar can you make a conprehansive video on aceptance criteria of DT please
ruclips.net/video/1dlbQtdf5wQ/видео.html
Welding and NDT sar ya men full dakh chuka hn destructive test ka bare men aceptence criteria par videoo plz
Plz make video on section 1
what is acceptance criteria as per uw52 asme sec 8 div 1 edition 2017
B31.3 radiography acceptance criteria also make one video plz same as like that
Sir,
You have given two times for acceptance criteria of rounded indication which one is needed to use in which condition
Acceptance criteria is explained in this article: www.weldingandndt.com/acceptance-criteria-for-weld-defects/
Sir good evening. Can you explain About B31. 3 ,B31.1, Film interpretation latest edition
Yes
நல்லது
Good ✨👍✨
Sir, could you please explain difference between Asme sec viii div1 and Asme sex ix for radiography test.
Sir need API 650 acceptance criteria
I have a doubt sir., We have separate sections for NDT ie) ASME section v for non destructive testing., Then why should we need to refer ASME sec viii div i?., I mean how we come to the conclusion that we have to refer sec viii rather than sec v.,
Sec V is only for NDT and it gives a general guideline for NDT (not acceptance criteria). However, Sec VIII is exclusively for pressure vessel and it contains everything pertaining to pressure vessel including the acceptance and rejection.
Somebody told cswip 3.1 welding inspector pattern will change from april. Is it true?
Asme b31.3 for round indications??
what is acceptance criteria for porosity when e=0.85 ,tungsten inclusion acceptance criteria????
Acceptance criteria is always determined by the applicable code of construction. It can not be generalized.
Thank you. Please visit my website www.weldingandndt.com/
Sir Please upload API- 650 Acceptance criteria
Sir please make a video on B31.1,B31.3,B31.4,B31.8and api1104
I think the explanation for the rounded indication is wrong.
Why do you think like that. Can you elaborate
As per ASME BPVC SEC VIII DIV 1 MANDATORY APPENDIX 4 (4-3). The indication which is more the (t/10) for t less than 3mm, 0.39mm for t between 3mm to 6mm, 0.79mm for t between 6mm to 50mm and 1.58mm for t more than 50mm will be considered as a relevant indication. Below to this dimension will not be considered as a relevant indication. The acceptance criteria for a relevant indication is (t/4) for a random indication and (t/3) for an isolated indication.
Deposit weld material You wrote T, actually it is t.
' T ' we use as plate/pipe thinkness
' t ' we use as weld deposit thinkness.
If anything wrong, please educate me.
Thank you.
Pls make a video about RTFI
Sure. Thank you. Please visit my website for notes, videos and other important informations www.weldingandndt.com/
Sir,
Kisi bhi 2material ko jab ham welding karate hai to usko welding karane me jitni electrode lagati hai usaka calculation karne ka tarika kya hai. Kripya batane ki kripa kare.
Aap ka channel bahut hi achha hai ha pcbc ke liye. Thanks
Per feet of weld length and thikness of weld portion kitna hai us par depend krta h
Thank you
Thank you. Please visit my website www.weldingandndt.com/
Sir need acceptance criteriab 31.3
Sure. Thank you. Please visit my website for notes, videos and other important informations www.weldingandndt.com/
your information about rejection of rounded indication is not correct
you tell about non relevant indication
we have to check only relevant indication
by the way nice work
thank youuu sir
Thanks. Please visit my website weldingandndt.com
n'existe pas la même explication en français
merci
please sir if we work in bliler project ; we take acceptance criteria from ASME I OR ASME 1 lead us to ASME VIII. THANK YOU
Thanks a lot. Please visit my website www.weldingandndt.com/
he only said Thanks a lot :)
you meant Boiler ??
👍🙏👍👍👍👍
Thank you. Please join my channel to watch all the videos. Joining Link: ruclips.net/channel/UCH7nXSievFlbRKzKzEySbkwjoin
SORRY BOILER PROJECT
The boiler is Project name ?? or equipment ?
you very good ,but your voice very trabl 🤦