cfl circuit hack everyone should know - dc 12 volt supply
HTML-код
- Опубликовано: 15 сен 2024
- cfl circuit hack everyone should know.
...
in this video about how to make dc voltage supply from a old cfl circuit.
if you like this video please like and subscribe
:)
My blog 👉deeptechtips12...
------
Music:-
1.Amadeus - Legendary [NCN VN Release]
• Amadeus | Legendary | ...
2. Music: Elektronomia - Summersong 2018
Watch: • Elektronomia - Summers...
------------------------------------------------------
best #cflcircuithack
#cfllightrepair#MrHomemade123
This project is very good!
Thank you v B nh Thu
super awesome idea brother !!!
i got sucsess test i got 15v 6amp using old 95w cfl to make the circuit work and to not overheat the transistor is to remove the electrolytic capacitor the 400volts one .the transistor will never get hot on it:)
I have two 10 uf 250v capacitors .which one should I remove?
@@power45118 it depend on the cfl driver if that is the filter cap from the rectified ac line its ok but if the capacitor is for the half bridge dont remove it
Isn’t the output frequency too high for those 1N4007 rectifying diodes ?
Copper wire thickness?
It's ok that it provides us 12v but what is it's wattage and amperage.
"I think 2 amps and 12V. It's a simple 12-volt DC converter, but it's getting hot, especially the copper wire."
you forgot to add diodes it means the video is fake. but ill still try
No brother it's not fake
In filamental bulb we don't have to add diode
But this circuit is not safe it getting hot in 5min of run
@@Dipranjan_Dihingia in my case i checked it on multimeter and it was showing 0.00 v
@@dggamer2758
The diagram clearly shows 4 diodes and a smoothing capacitor arranged to create a full bridge rectifier on the 12 volt (DC) side.
The lack of a rectifier in the video doesn't effect a load that functions on both AC & DC (tungsten filament bulbs, internally commutated motors, ni-chrome heater coils, etc.)
The most likely point of failure in building this circuit is the electrolytic capacitors.
Those things will go bad over time, even if they aren't being used.
Should they all check out, a resistor is second most likely to be at fault.
Every manufacturer had to find their own way to shorten the life of CFL bulbs though, so there will be at least one component that sticks out as "just barely in spec".
Engineered obsolescence... They don't make as much money if their product is well built.
Excellent..
Thank you :)
plz mention the copper wire thickness.
i have try it with 12v 5wat led . it works only for 5 or 10minute's. after that time it damage the cfl Circuit
cfl i use 15w
Yes bro, it's produce heat.thanks for your comment.:-)
use bigger bulky transistor like 600v 50a TO-220 package or wind the input chock much more coil to increase the resistance
@@stingerbold9327 which trinsistor plaese mention the name
@@stingerbold9327 Tq bro 😀
@@naimehossen14 i highly recommend use E13009l or mje13009 mje13007 these can handle ton of power without any problem if you use E13009l heatsink not necessary
24turn wala wire kaha pa connect waha
is input voltage 12v? or output
?
No input voltage 220 ac current and output 12volt dc
@@Dipranjan_Dihingia thank you
@@FlowVirm welcome 😊
Where shall i connect 2 terminals of transformer ?
What is the thickness of the coil bro
Bol kr btao dost yeh kya music suna rhay ho?
Meter say cfl k circuit output voltages check kro phir btao kam krnay hain ya barhaanay hain.
Yeh tou uni l lecture say b mushkil kaam mak daal diyya ha
Background music is very high and you haven’t shown 24 turns winding connection to circuit so explain
Per 2turn give you 1volt AC current. I just converted the inductor to a transformer ,simple 😊.sorry for the background music
Diode shoud be SR360 model or Schottky diodes
where did you soldered it
Baht lambi video hai
Sorry about that.😀 thanks for your comment...
Only 3 minutes life.
Mera cfl circit jal gaya
Don't turn too much.its also depend on your cfl circuit Watt.
Bhai mera bhi channels dhek lo please support me channel name Ak series vlog technology replied jarur karna
Ha bro,mane dekha new channel hain video dalte roho.joldi grow hoga Tumare channel 😊👍
remove the electolytic capacitor the 400v 3to 10uf it will not overheat your transistor anymore
Very slow work
बेकार