@@el_chavalo5.3 b4 i got my intake done my car was making 250 according to the horse power calculator so a bolt on 3.8 is about on par with a stock pi 4.6 but my 3.8 will run circle around my non pi 4.6 cougar
Wow dude, nice to see a more recent video of people appreciating these V6’s. I have 2 and although I see a new edge coyote swap in my future, my V6s have been incredibly reliable.
@@Rx_Lee I heard the tick with the v6 is exhaust manifold due to A/C condensation dripping down from the compressor. But my tick goes away after about 3000rpm
This video inspired me to mod my 3.9 mustang a long time ago. I went with the a 2007 Ford Freestar intake swap I learned from Grant Paradox Johnson instead on my automatic and my best 0 to 60 to date is 5.7 secs. Best part is it fits inside the 2004 v6 hood (cobra hood). I still gotta delete my Powersteering but havent because I plan to make it electric. It's just quite a project. I do have a bunch of other mods (long tubes, 4.10s, LSD, 65mm TB, CAI, and more). Anyways I never thought my mustang would be similar in speed to yours. I'm so stoked! They are fun ass cars that never got the credit they deserved. I'm going to install the 2007 freestar camshaft as well which will be another major boost for me. They are both Essex engines and parts interchangeable. I still come to this video from time to time to compare my speed to yours lol.
You should look into doing the IAC mod so your RPM's drop faster and don't have the deal with the idle hang. It takes about 5-10 mins to finish and its very simple, all you need is a sheet of gasket material and a drill bit to make the IAC ports smaller. If you don't like how it responds after the IAC mod then its literally 2 bolts and switch back to stock gasket.
Nice! I drive an Audi S5 now but miss my 99 V6 Mustang. Had it through high school and college and it never let me down. Good car to learn how to fix and modify cars.
Very nice. I wish my V6 was a 5 speed. But that's ok cuz my mach1 is lol. What surprised me thou was the quality of the v6. They are very good cars. Mine has 200,000 on the dash and besides the heater core everything works perfectly.
My v6 has 210k on it. Bought it a month ago and have had to rebuild the front end when I got it, just bought a new torque converter with a 500rpm increase in stall speed over stock (cause the stock one went out) I got new high flow cats from magnaflow (the stock ones blew out, literally blew apart at the welds near the headers) and a dual catback exhaust system from Magnaflow also. I got a new screamin demon coil pack to replace the stock one with 210k miles on it new low resistance performance wires and double platinum plugs that have been regapped to .065 instead of .045 because of the new coil pack, but other than that the car is a beast and runs great.
Im getting a ported lower and ported f150 on my 04 right now i also have comp cam full exhaust 68 mm throttle body 3.73 gears and custom tune hoping for a similar 0 to 60
i own a 3.8l mustang, I've done all the fuel system upgrades, high flow injectors, race fuel pump, and i went from running 6.30's to 4.80's, i love how easy it is to wake up the car with little mods, definitely going for a Windstar intake next and an off road h pipe exhaust, then comes the procharger, hopefully by then ill be make 650 hp, which for a 3.8 is amazing.
I got an '04 3.9 with a Bama tune(definately worked on mine), BBKshorty headers, dual dumps, and an SR cold air intake. It only has 205 wides on 16x7 inch wheels, pretty small, and pulled a 6.4 second 0-60 spinning. I desperately need bigger tires eventually, I'd imagine i could take off a half second or more with 255's.
What are you guys smoking? Do the same bolt ons to the 4.6 and it'd still be faster. Not hating on the 3.8 at all, still want to buy a 3.8 mustang and build it to a cammed 4.2 for fun. But dang
@@TheVulcan Update- I've hooked up the 4.2 upper intake manifold now but without porting it yet... I've noticed a good power gain! These V6 mustangs are pretty awesome honestly and I'm glad I got it as my first project car haha. By any chance could I get a link to the hood cowl you bought that you show in the 0-100 video?
@@jasonpooler6811 i hv the f150 intake for mine but theres a lot of outlets on it for hoses. Theres 2 or 3 underneath and 2csmall ones on the back on passenger side. Can you tell me where to connect them
@@talknheadz well, I don’t exactly remember but if you can find a place to put the hose in I’d say cap it off.. I also bypassed the egr and removed it... I had to add length to wires to make connectors connectable. I sold mine though, but yea you got this 🤙🏽
Did you experience a decrease in top speed with the swap compared to the stock What parts did you have to buy outside of the manifold for this mod to work
I have a 4.6 2v, leaving the airbox stock and throwing in a washable k&n but might get bigger maf. Also doing a third cat and exaust delete. The final and most expensive mods will be sct tuner, throttle body, 4.10 gears
My 3.8 was recently destroyed at 103,000 original miles due to debris on the highway rupturing the oil pan. The driver at the time drove it for about 5 minutes with no oil. I was thinking about buying a remanufactured engine but have recently been steering more towards a hot rod 3.8 build
@Shttnmoney how's that engine swap coming along? I just barely got in a position where I can buy the rebuild kit for mine. I got a damn speeding ticket last month
I noticed you deleted the egr line that is goes connected to the manifold. What did you put or how did you do the delete? I’m curious as I broke one of the lines that gets connected with an air hose to the egr pressure feedback sensor. So air pressure is making my v6 misfire like crazy. I tried JB weld & it doesn’t hold it in.
I installed headers and removed all of that, removed the egr system send sensors entirely. The bought a block off plate to where the egr connected to the lower intake manifold. I got codes for removing the sensors but as long as it runs perfectly fine idc
Pretty sure it fits right on. The Essex came in 3.8 and 4.2 for cars and trucks respectively. So people stroke 3.8s to 4.3 and use the 4.2 parts to do it
No i got a Manual with 3.27 and a beefy 18x10s in the rear. Stock the manuals are 1 whole second faster than the autos, which is like 6.9 seconds with a sticky summer tire. That's why i only drive manual 3.8s.
That's crazy I got mine and yes it's a 2001 mustang 3.8l v6 it has supersix Motorsports powerpaks BBk headers tuned and cold air intake and do a very surprising even I dident want to believe a 0-60 in 4.6 sec and beat a 2000 Pontiac WS6 5.7 anything's possible if you know what your doing remember if anyone is "like oh a v6" just laugh and them them keep thinking you slow till it's time to race
There is no way possible a v6 of this year with the minor mods you mentioned can do 0-60 in 4.6. Unless by powerpak you mean it's supercharged or something. I could see a supercharged OR a fully built v6 beating a stock ta and doing times like that but no way its happening with your minor mods you claim.
mm have u tried better fuel injectors might need a tune..with new fuel pump i like the power steering delete i maydo that since mine is a pos. how hard is it to turn
I know this video is a bit old, but how far above the stock hood does the IAC and throttle cable plate stick? I've got a F150 manifold I'd like to use, and I'm debating between the 3.5" and 4" Cervini hoods.
@@TheVulcan Thanks for the quick reply! I've got an '01 with a 5-speed that's a good candidate for the F150 swap, though I don't think it'll be quite as fast as yours given that I'll still have AC and PS connected. After watching your other videos I'm curious just how much HP/TQ the F150 mani is worth.
Wait, you don't have power steering anymore? Seeings as I'm doing this for my fiancé's car, I don't know if she'd like that...I def wouldn't mind tho. It's unnecessary...especially if your doing it for straight line speed.
Can a full bolt on v6 3.8 beat a g35 2008 sedan ? Mustang- Performance fuel system , cold air intake , catback , msd coild pack , 4.2 intake manifold , and soon long tubes and bahama tune , should do the job right ?
Hey really hope you’re still active but when you did the swap so you pull the wiring harness and ecu aswell? I just did this swap on my mustang and it’s cranking but not starting
It doesn’t, just frees up some crank horsepower, so like on a stick manual 3.8L in good conditions Will normally put out 170whp on a good day. With the power steering pump, a/c deleted you looking at more like 180whp.
Ayo, I know this is old but im back here again but I discovered that the Ford Ranger Crank fits the 3.8 and 3.9 block to give it a deeper stroke. dyno at 210 with ethanol kit.
I am indefinitely going to put a different rear end gear in my 3.8 Also a portmatch!! I like the idea you did with the intake also I'm going to do away with the hydraulic power steering and upgrade to and EPS and also I have a sunroof in my car I'm going to do away with the AC to help gain more power and do away with the clutch fan input electric fans in and where I have it automatic transmission I'm going to keep a manual radiator and go with a transmission cooler for the transmission fluid!! And do away with mufflers and put a drone delete cat back on it!! Hopefully we'll get more torque and power out of the little 3.8 V6 They actually have just as much horsepower as the old 1978 Cobra 2 with 302 139HP but it's crazy that the old 1978 cover twos only weighed 2,990lb and these 4th generations mustang weigh over 4,600 lb the old cober 2 had an OEM 0 to 60 around 6.3 seconds with the c4 transmission!!😮 😅😊😂
Do you have gears? If not, get some 4.10s lol it’ll rip hard off a dig. And I’d say get a BBK throttle body. It’ll make a good difference with the ported manifolds. Stock manifolds it won’t do much
Lifters are cold right? That’s what I always though it was just don’t drive it cold it’ll go away once it’s warm unless yours is doing it while it’s warm than that’s bad lifters idk
The Vulcan Thanks man... great job. You are the definition of old school hot roddin.... makin stuff fast for cheap! Those headers shorty? Have you run quarter mile yet? Surprised any other unsuspecting cars?
@@GPMAX01 shorty headers, because of the more torque bias manifold using LTs would improve top end but drop torque, and basically clash negitively. So i used shorties to improve both torque and hp, im trying to make the most possible NA power with a solid redline of between 5200rpm - 5800rpm. And basically with just a manifold and headers i put it in the neighborhood of a 2valve new edge stang, and i havent tuned it and the 0-60 was around 5.7 seconds with a bad Mass air flow sensor, running only 87 pump gas. Also my power steering is deleted.
The Vulcan impressive bro! I always look forward to your channel updates. I have a few Ford’s myself including a ranger that is getting more deadly thanks to you!
The f-150 intake increases torque by a huge margin, i also ported it, also i have Headers. A stock one manual 3.8 with a good tire set up can his 60 in 6.8 seconds. Stock Autos more like 8 seconds. Somethings up with yours. Tune and cold air won't do much by itself
@@tylersolomon9659 yeeaaahh higher elivation can drop your 0-60 times 1-2 seconds. Do the windstar manifold swap or the F-150 manifold swap, long tube Headers, weight reduction, and gears.
I deleted it because of the annoying wine the I couldn't get rid of. You'll see some gains at high RPM, But if you're not comfortable with the tougher steering, you shouldn't. I'm very strong so it never bothered me and I like heavy steering.
Depends on your skill level I guess. But you'd rent a pully puller from the auto part store. Remove the pully then pump. That's easy. Key part: you must drain some, not all fluid from the rack, then cut the lines short, then you'll take some fuel line then loop the lines, or connect them together. This is commonly done on Hondas civic and integras. so there are many videos on it, if you need further guidance.
Ported the opening where the throttle body is then i only ported/gasket matched the 6 short runners and left the 6 long skinny runners alone. On the F150 manifold on these cars the 6 short runners start big then as it gets closer the the lower intake manifold the ports get smaller to where you can actually feel a lip so porting the short runners all the way through isnt needed. But the 6 long skinny runners(for torque) i left alone. But in these cars you gain about 15hp, and 30tq with just swapping to this manifold not even ported because the stock one is so crappy. In case of the 4.0L all you can do is port the manifold, and maybe add a bigger throttle body.
Im sure the engineers that design this mustang and the engineers that design the f-150 they did it to people don't look into your hoor from a 100 feet away
I call bullshit.. he has headers and a 4.2l intake off a truck .. he says is ported ..key word says .. stock heads stock cams cold air intake possibly mufflers. did not mentions changing the cam or the tune or the gears .. face it people the 3.8L is a turd and just those few lil mods is not going to shine a turd golden. you have only his word it goes this fast nothing more. I give credit where credit is due and he did not even say he removed the godawful power sucking cats on exhaust either. you realize these turds came from the factory with 2.73 rear ends right ? you realize how much hp is needed to propel a mustang zero to 60 with those space shuttle gears ? dont know off hand but a fucking shit load is my guess possibly 5 times the stock hp of that car
Dude. At least do your research before trying to talk shit. The fact that you dont even know gearing differences between mustang years you loose all credibility 🤣🤣1999-2004 manual v6 mustang come with 3.27 gears. not 2.73(11-14 v6 mustang). I didnt state exactly everything i did. Full A/C delete and P/S delete, along with full weight reduction, everything behind the front 2 seats are stripped including rear seats. And im not going put on video that i cut my cats off, that's just dumb. Also the reason i why the F150 manifold is best for a sharp torque increase only, and is the best fit for stock cam which gives it a good 0-60 but over 100mph falls on its face, if i wanted to use a cam i would've used a different manifold that's rpm focused. On all my vehicles I port the upper, lower and throttlebody. It's easy to be a keyboard warrior ain't it?
@@mathewhoffer4541 I said it's quick, not fast. You having a high HP car apparently should know the difference between those words. These cars will never be *fast without boost or a heavy build.
I used to own a 3.8 with full bolt ons, engines are surprisingly powerful when woken up, your car is just plain badass
How many hp
@@el_chavalo5.3 b4 i got my intake done my car was making 250 according to the horse power calculator so a bolt on 3.8 is about on par with a stock pi 4.6 but my 3.8 will run circle around my non pi 4.6 cougar
@@whatsreallygoingon253 oh ok thanks for the info
What bolt ons did you have
Wow dude, nice to see a more recent video of people appreciating these V6’s. I have 2 and although I see a new edge coyote swap in my future, my V6s have been incredibly reliable.
They are very reliable, my 2000 V6 has 180k miles and only has a slight lifter tick under load but most fords have that slight tick.
@@Rx_Lee I heard the tick with the v6 is exhaust manifold due to A/C condensation dripping down from the compressor.
But my tick goes away after about 3000rpm
This video inspired me to mod my 3.9 mustang a long time ago. I went with the a 2007 Ford Freestar intake swap I learned from Grant Paradox Johnson instead on my automatic and my best 0 to 60 to date is 5.7 secs. Best part is it fits inside the 2004 v6 hood (cobra hood). I still gotta delete my Powersteering but havent because I plan to make it electric. It's just quite a project. I do have a bunch of other mods (long tubes, 4.10s, LSD, 65mm TB, CAI, and more).
Anyways I never thought my mustang would be similar in speed to yours. I'm so stoked! They are fun ass cars that never got the credit they deserved. I'm going to install the 2007 freestar camshaft as well which will be another major boost for me. They are both Essex engines and parts interchangeable. I still come to this video from time to time to compare my speed to yours lol.
You should look into doing the IAC mod so your RPM's drop faster and don't have the deal with the idle hang. It takes about 5-10 mins to finish and its very simple, all you need is a sheet of gasket material and a drill bit to make the IAC ports smaller. If you don't like how it responds after the IAC mod then its literally 2 bolts and switch back to stock gasket.
Where can I get a tutorial to this!
@@0rvelazqu ruclips.net/video/Rze8DJsi9f4/видео.html&ab_channel=UnTamedMustang
Im assuming you simply drill smaller holes into the gasket and place the gasket over the old ports ?
Nice! I drive an Audi S5 now but miss my 99 V6 Mustang. Had it through high school and college and it never let me down. Good car to learn how to fix and modify cars.
Very nice. I wish my V6 was a 5 speed. But that's ok cuz my mach1 is lol. What surprised me thou was the quality of the v6. They are very good cars. Mine has 200,000 on the dash and besides the heater core everything works perfectly.
Flush that baby out.
It leaks so i bypassed it.
My v6 has 210k on it. Bought it a month ago and have had to rebuild the front end when I got it, just bought a new torque converter with a 500rpm increase in stall speed over stock (cause the stock one went out) I got new high flow cats from magnaflow (the stock ones blew out, literally blew apart at the welds near the headers) and a dual catback exhaust system from Magnaflow also. I got a new screamin demon coil pack to replace the stock one with 210k miles on it new low resistance performance wires and double platinum plugs that have been regapped to .065 instead of .045 because of the new coil pack, but other than that the car is a beast and runs great.
I’m hoping I can get my 99 v6 that fast!
Am I the only one who noticed the video starts with him going 10mph?
Im getting a ported lower and ported f150 on my 04 right now i also have comp cam full exhaust 68 mm throttle body 3.73 gears and custom tune hoping for a similar 0 to 60
i own a 3.8l mustang, I've done all the fuel system upgrades, high flow injectors, race fuel pump, and i went from running 6.30's to 4.80's, i love how easy it is to wake up the car with little mods, definitely going for a Windstar intake next and an off road h pipe exhaust, then comes the procharger, hopefully by then ill be make 650 hp, which for a 3.8 is amazing.
What fuel pump and injectors you got in that pony?
just change ur rear to 4:10 and your acceleration will be much better
transmission cant handle that stock, your engine internals top to bottom are gonna blow, probably will throw a rod
reinforcement is key
I got an '04 3.9 with a Bama tune(definately worked on mine), BBKshorty headers, dual dumps, and an SR cold air intake. It only has 205 wides on 16x7 inch wheels, pretty small, and pulled a 6.4 second 0-60 spinning. I desperately need bigger tires eventually, I'd imagine i could take off a half second or more with 255's.
@@AlexSmith-iv2jv go 275 if you don't have an LSD
@TheVulcan im fs planning on doing a limited slip and 3.73's
That’s pretty quick man, that’ll give a 1990-2004 GT a pretty solid run
that would smoke a gt lmao
It would blow the doors off a GT
Dude doesn’t anything about the GTs of that era lol 200 horses built for spinning the wheels in 1st that’s about it
What are you guys smoking? Do the same bolt ons to the 4.6 and it'd still be faster. Not hating on the 3.8 at all, still want to buy a 3.8 mustang and build it to a cammed 4.2 for fun. But dang
Would not give my gt any type of runs for its money
What size is the replacement serpentine belt? Wouldn't happen to still recall the serp length w/ only power steering?
How much of a difference does the f150 intake manifold make compared to a regular aftermarket intake? Beautiful car btw
How long was the belt you used to bypass the power steering? I need a point of reference to start from for my car.
A cowl hood will give you plenty of clearance and it will look good on it too. Nice setup.
I have one, just haven't installed it yet. I really need to though
@@TheVulcan Update- I've hooked up the 4.2 upper intake manifold now but without porting it yet... I've noticed a good power gain! These V6 mustangs are pretty awesome honestly and I'm glad I got it as my first project car haha. By any chance could I get a link to the hood cowl you bought that you show in the 0-100 video?
@@jasonpooler6811 i hv the f150 intake for mine but theres a lot of outlets on it for hoses. Theres 2 or 3 underneath and 2csmall ones on the back on passenger side. Can you tell me where to connect them
@@talknheadz well, I don’t exactly remember but if you can find a place to put the hose in I’d say cap it off.. I also bypassed the egr and removed it... I had to add length to wires to make connectors connectable. I sold mine though, but yea you got this 🤙🏽
@@jasonpooler6811 cool. Thanks bro
What year was the f150?
1997-99
4.6l* not 4.2l
No..... 1997- 1999 4.2L v6 😑
Oh gotcha it looked like a 4.6l plenum mb.
Do you think the f150 intake manifold fit well on on my 2001 3.8 mustang and can you add a turbo on it too ?
Did you experience a decrease in top speed with the swap compared to the stock
What parts did you have to buy outside of the manifold for this mod to work
I have a 4.6 2v, leaving the airbox stock and throwing in a washable k&n but might get bigger maf. Also doing a third cat and exaust delete. The final and most expensive mods will be sct tuner, throttle body, 4.10 gears
Definitely gonna do this. Also a cowl hood.
Anything one should know before doing it? How long did it take you?
Did you make power past 4k rpm before this swap? My power band is from 2k to 4.2 k
My 3.8 was recently destroyed at 103,000 original miles due to debris on the highway rupturing the oil pan. The driver at the time drove it for about 5 minutes with no oil. I was thinking about buying a remanufactured engine but have recently been steering more towards a hot rod 3.8 build
Same shii happened to me. Something broke my oil pan and I drove it wit no oil to the shop. Now I’m getting an engine swap
@Shttnmoney what you gonna drop in it? To this day I'm still rebuilding my 3.8 I just got the block back from the shop
@@0rvelazqu I found a 3.8 at a junk yard with decent mileage and I’m planning to do this f150 upper intake manifold
@Shttnmoney how's that engine swap coming along? I just barely got in a position where I can buy the rebuild kit for mine. I got a damn speeding ticket last month
Where did you hook the coil pack up at,
CorvetteZR1 wondering that myself too
I bought a sct X4 tuner for my v6 3.8 L 2003 but it didnt have any tunes on it. How do I get the tune for it?
It should automatically have can tunes for the 3.8L.
Unless you didn't buy a ford specific x4
@@TheVulcan it says that their is no custom tunes do I have to go online and download it to the tuner first?
@@calebyamaguchi7371 there should be SCT preloaded tunes on it. Thats ehat i use. Otherwise you'll have to get one custom from BAMA, or Steeda
@@TheVulcan okay thanks for the help
So I’ve got a 3.8l and still trying find a supercharger any no where to find good one
I noticed you deleted the egr line that is goes connected to the manifold. What did you put or how did you do the delete? I’m curious as I broke one of the lines that gets connected with an air hose to the egr pressure feedback sensor. So air pressure is making my v6 misfire like crazy. I tried JB weld & it doesn’t hold it in.
I installed headers and removed all of that, removed the egr system send sensors entirely. The bought a block off plate to where the egr connected to the lower intake manifold. I got codes for removing the sensors but as long as it runs perfectly fine idc
Looks Great ❤
*Should be able to get a 4.6 throttle body to work for some extra oomph..*
I keep coming back to this video. I'm trying to get my 2003 v6 3.8L this fast. What tires do you got on your rear?
Modlist in this video. Ported f150 intake, ported throttle body, throttle body spacer, headers, 93 octane tune. 275/35/18s in the rear.
What year of f150 would his be
Hey man Great video. Im wonder what you had to do to get the intake to fit on the engine? Thanks
Pretty sure it fits right on. The Essex came in 3.8 and 4.2 for cars and trucks respectively. So people stroke 3.8s to 4.3 and use the 4.2 parts to do it
@@jackryan4313 that makes sense. Thanks for sharing the info!
Will it fit with the anniversary hood? A guy on a forum said it would but I highly doubt that
Do you have gears and an lsd? I'm a fbo v6 with auto and 3.55s, and still only do 0-60 in 7.5
No i got a Manual with 3.27 and a beefy 18x10s in the rear. Stock the manuals are 1 whole second faster than the autos, which is like 6.9 seconds with a sticky summer tire. That's why i only drive manual 3.8s.
That's crazy I got mine and yes it's a 2001 mustang 3.8l v6 it has supersix Motorsports powerpaks BBk headers tuned and cold air intake and do a very surprising even I dident want to believe a 0-60 in 4.6 sec and beat a 2000 Pontiac WS6 5.7 anything's possible if you know what your doing remember if anyone is "like oh a v6" just laugh and them them keep thinking you slow till it's time to race
Yeah mine is still realitivly stock besides the massive torque gain from the f-150 swap, shorties and intake.
There is no way possible a v6 of this year with the minor mods you mentioned can do 0-60 in 4.6. Unless by powerpak you mean it's supercharged or something. I could see a supercharged OR a fully built v6 beating a stock ta and doing times like that but no way its happening with your minor mods you claim.
mm have u tried better fuel injectors might need a tune..with new fuel pump
i like the power steering delete i maydo that since mine is a pos. how hard is it to turn
I know this video is a bit old, but how far above the stock hood does the IAC and throttle cable plate stick? I've got a F150 manifold I'd like to use, and I'm debating between the 3.5" and 4" Cervini hoods.
About 4-5inches
@@TheVulcan Thanks for the quick reply! I've got an '01 with a 5-speed that's a good candidate for the F150 swap, though I don't think it'll be quite as fast as yours given that I'll still have AC and PS connected. After watching your other videos I'm curious just how much HP/TQ the F150 mani is worth.
@@RGW-NC87 hp gains will match the windstar swap. There will just be Very large torque gains. Best manifold if your planning on staying stock cam.
Wait, you don't have power steering anymore? Seeings as I'm doing this for my fiancé's car, I don't know if she'd like that...I def wouldn't mind tho. It's unnecessary...especially if your doing it for straight line speed.
About how much all the way around did it cost u to get all the parts and put together??
What is it like driving without powersteerong
Can a full bolt on v6 3.8 beat a g35 2008 sedan ? Mustang- Performance fuel system , cold air intake , catback , msd coild pack , 4.2 intake manifold , and soon long tubes and bahama tune , should do the job right ?
Yup. If it’s stock
Yo my brother, what parts would I need from an F-150 to add this to the stock 3.8L v6 Engine?
Did you use factory throttle body
Hey really hope you’re still active but when you did the swap so you pull the wiring harness and ecu aswell? I just did this swap on my mustang and it’s cranking but not starting
Is your egr wired right
@@chelseacoolidge1225 f
Fairly certain an egr wouldn’t cause a no start condition
What year make and model vehicle was that intake made for! Ik you said f150 but I wanna do this and would like the info
1997-1999 4.2L v6 f-150
I’ve seen deleting the power steering pump gives the car 40hp. I forgot what video it was but it was sponsored by AMS oil
It doesn’t, just frees up some crank horsepower, so like on a stick manual 3.8L in good conditions Will normally put out 170whp on a good day. With the power steering pump, a/c deleted you looking at more like 180whp.
Ayo, I know this is old but im back here again but I discovered that the Ford Ranger Crank fits the 3.8 and 3.9 block to give it a deeper stroke. dyno at 210 with ethanol kit.
I am indefinitely going to put a different rear end gear in my 3.8 Also a portmatch!! I like the idea you did with the intake also I'm going to do away with the hydraulic power steering and upgrade to and EPS and also I have a sunroof in my car I'm going to do away with the AC to help gain more power and do away with the clutch fan input electric fans in and where I have it automatic transmission I'm going to keep a manual radiator and go with a transmission cooler for the transmission fluid!! And do away with mufflers and put a drone delete cat back on it!! Hopefully we'll get more torque and power out of the little 3.8 V6 They actually have just as much horsepower as the old 1978 Cobra 2 with 302 139HP but it's crazy that the old 1978 cover twos only weighed 2,990lb and these 4th generations mustang weigh over 4,600 lb the old cober 2 had an OEM 0 to 60 around 6.3 seconds with the c4 transmission!!😮 😅😊😂
Where did you see that they weigh 4600 pounds? My 98 weighs 3000 pounds empty
The bottom of the description had me
how much was all of that ?
Could it the f150 intake under a 3inch cawl hood
What intake are you using?
Not mentioned in the video: You also removed the EGR connection and valve.
Do you have gears? If not, get some 4.10s lol it’ll rip hard off a dig. And I’d say get a BBK throttle body. It’ll make a good difference with the ported manifolds. Stock manifolds it won’t do much
I do not but taking my power band into consideration with the f150 swap 4.10s aren't a good idea. And i already did lol.
It probably would've been a little quicker if i actually launched it instead of soft launching it
What f150 manifold did he use
1997-1999 4.2 f150 manifold
hey man I have the same type of knocking sound so far my car still runs great. I'm just worried
Lifters are cold right? That’s what I always though it was just don’t drive it cold it’ll go away once it’s warm unless yours is doing it while it’s warm than that’s bad lifters idk
@@joelbigdays47 i fixed it, it was my balance shaft
What the gear set final drive is in there.?
Stock 3.27
The Vulcan Thanks man... great job. You are the definition of old school hot roddin.... makin stuff fast for cheap!
Those headers shorty? Have you run quarter mile yet? Surprised any other unsuspecting cars?
@@GPMAX01 shorty headers, because of the more torque bias manifold using LTs would improve top end but drop torque, and basically clash negitively. So i used shorties to improve both torque and hp, im trying to make the most possible NA power with a solid redline of between 5200rpm - 5800rpm. And basically with just a manifold and headers i put it in the neighborhood of a 2valve new edge stang, and i havent tuned it and the 0-60 was around 5.7 seconds with a bad Mass air flow sensor, running only 87 pump gas. Also my power steering is deleted.
Only car ive raced so far is my coworkers challenger RT, and i pulled on him. And he couldnt believe it. But he lost
The Vulcan impressive bro! I always look forward to your channel updates. I have a few Ford’s myself including a ranger that is getting more deadly thanks to you!
Awesome bro👍
Question why didn't you just get a cheat cowl induction hood?
Old video, i do have one
@@TheVulcan yeah I saw the other video and was like whoops lol
I would buy one though if I was you they aren't as expensive as they use to be a new one can be had for 300 bucks
Mine is stock except exhaust, rims, heads and rear gears and does that
I wonder what’s wrong with mine. I have cold air intake and Sct 91 octane tune with a muffler delete, and my shit does 0-60 in 10 seconds
Automatic?
The f-150 intake increases torque by a huge margin, i also ported it, also i have Headers. A stock one manual 3.8 with a good tire set up can his 60 in 6.8 seconds. Stock Autos more like 8 seconds. Somethings up with yours. Tune and cold air won't do much by itself
@@TheVulcan I heard Colorados air might also do something. And yeah it’s automatic
@@TheVulcan what’s one thing I can do to get the most out of the V6? Weight reduction?
@@tylersolomon9659 yeeaaahh higher elivation can drop your 0-60 times 1-2 seconds. Do the windstar manifold swap or the F-150 manifold swap, long tube Headers, weight reduction, and gears.
will this work with an automatic?
Yes, the IAC may be temperamental tho. But the big torque bump would help big time when going threw them long ass gears
Should I delete my power steering?
I deleted it because of the annoying wine the I couldn't get rid of. You'll see some gains at high RPM, But if you're not comfortable with the tougher steering, you shouldn't. I'm very strong so it never bothered me and I like heavy steering.
@@TheVulcan Is it an easy removal
Depends on your skill level I guess. But you'd rent a pully puller from the auto part store. Remove the pully then pump. That's easy. Key part: you must drain some, not all fluid from the rack, then cut the lines short, then you'll take some fuel line then loop the lines, or connect them together. This is commonly done on Hondas civic and integras. so there are many videos on it, if you need further guidance.
@@TheVulcan alright Thank for that advice 👌 i want to delete it from my car too
Any of these mods work on the 4.0 stamps?
4.0 is an entirely different engine than the 3.8L. There really isn't any manifold swaps for the 4.0L and very little aftermarked support
The Vulcan what did you use to port the manifold? Did you just match the gasket holes or port the entire way through?
Ported the opening where the throttle body is then i only ported/gasket matched the 6 short runners and left the 6 long skinny runners alone. On the F150 manifold on these cars the 6 short runners start big then as it gets closer the the lower intake manifold the ports get smaller to where you can actually feel a lip so porting the short runners all the way through isnt needed. But the 6 long skinny runners(for torque) i left alone. But in these cars you gain about 15hp, and 30tq with just swapping to this manifold not even ported because the stock one is so crappy. In case of the 4.0L all you can do is port the manifold, and maybe add a bigger throttle body.
The 98 windstar intake would fit alot better than the f150
What year f150 is it
1998
Yep, sounds like a gerbil. Just like mine.
Im sure the engineers that design this mustang and the engineers that design the f-150 they did it to people don't look into your hoor from a 100 feet away
If it’s cool do you know where I could find the intake haha
Junk yard or ebay
Preciate it🤟🏽 and also what year haha idk about the f150 tbh
@@jasonpooler6811 1999-2000
The Vulcan Can’t wait you get my ride quick haha
Have you looked at the cowl 4 inch hood seeing if that could work would look pretty good
Is it standard or automatic
Manual transmission
Now tune it with a sct and watch your eyes pop
How do you tune it with the Sct?
why not just get a cowl hood
Cowl hood
race a gt of the same gen
Ive raced 2 stock new edge 2 valves and won both times.
@@TheVulcan hell yeah man! have u got any vids? i’m thinking about getting a project v6 and doing this
You need a new rack n your steering would be fine its not the pumps fault but anyway this is my plan! F150 fuck a windstar ha
@sixstanger00
Power steering delete
I call bullshit.. he has headers and a 4.2l intake off a truck .. he says is ported ..key word says .. stock heads stock cams cold air intake possibly mufflers. did not mentions changing the cam or the tune or the gears .. face it people the 3.8L is a turd and just those few lil mods is not going to shine a turd golden. you have only his word it goes this fast nothing more. I give credit where credit is due and he did not even say he removed the godawful power sucking cats on exhaust either. you realize these turds came from the factory with 2.73 rear ends right ? you realize how much hp is needed to propel a mustang zero to 60 with those space shuttle gears ? dont know off hand but a fucking shit load is my guess possibly 5 times the stock hp of that car
so this is what you get when someone who doesnt know jack about cars makes a u tube video and tries to bull shit his way through it :)
Dude. At least do your research before trying to talk shit. The fact that you dont even know gearing differences between mustang years you loose all credibility 🤣🤣1999-2004 manual v6 mustang come with 3.27 gears. not 2.73(11-14 v6 mustang). I didnt state exactly everything i did. Full A/C delete and P/S delete, along with full weight reduction, everything behind the front 2 seats are stripped including rear seats. And im not going put on video that i cut my cats off, that's just dumb. Also the reason i why the F150 manifold is best for a sharp torque increase only, and is the best fit for stock cam which gives it a good 0-60 but over 100mph falls on its face, if i wanted to use a cam i would've used a different manifold that's rpm focused. On all my vehicles I port the upper, lower and throttlebody. It's easy to be a keyboard warrior ain't it?
@@mathewhoffer4541 I said it's quick, not fast. You having a high HP car apparently should know the difference between those words. These cars will never be *fast without boost or a heavy build.