17:30 - Quick tip. Tape the camera down with some Kapton tape. Tape the four wires down close to where they will go also with Kapton tape. Hold them in place with tweezers to aid soldering.
Mobile Phone camera modules follow MIPI protocol mostly. I wonder how you have managed hook it directly to USB. Please post a brief about interface topology.
For those asking how he found the camera pin connection diagram: Using multimeter before removing the camera from phone motherboard, then 1. GND is very easy to find, it is shorted to GND of the phone 2. V+ is the 5V input from phone (this might be the hardest to find if you don't have experience in tracing the input voltage). Find pin that has no connection with the GND (but there might be more than one). The OP found out using diode test but does not show which one to test. Another way to find out 5V rail is to find the Power IC or Mosfet that gives the 5V to whole motherboard and find the direct connection. While the data lines are typically not directly connected to power rail (it has connection but has pull-up resistor like 10k Ohm) but directly connected to one of motherboard SOC leg. 3. Then the rest of D+ and D- are found by trial and error (using permutation). First, the testing is done by soldering & jumpering the pins of the camera (while camera still attached in phone board) directly to USB and then PC as seen in 8:09. And NOTE that only some cameras support direct USB interface. So, this will work only on few phone models. And if you guess the 5V line wrong, you might permanently damage the whole system.
What a fantastic video! Very well done! Up close viewing with the specifics. Written out what was needed to know. Very very well done!! Thank you for sharing this!
Great work! I thought I was the only one who makes things like this..plus great soldering job, especially not using a super fine point soldering iron! Those camera wires are damn hard to see and work with sometimes..Keep up the awesome work! Just subscribed..
He will not answer your questio cos he fund the GND and Volt also + DATA and _ DATA 4 wires that you asked about that!!! And with only a voltmeter no one can find them!!! Otherwise you must a perfect of this monile board!!!
Mini spy camera in awasome My query 1) does the mini spy cam for recording also for hours 2) where can we get the surface paper as used in this project
I have a mic which is familiarly used with CCTV camera's. I wanna use that mic as a external mic for videos. 4 wires are there... Shall i make it like this??? One side Micro USB & another side mic... Do you prefer any app to record my audio if i made???
what do you think would be the latest (potentially best) phone camera with usb-controller built in? because i guess modern phone cams won`t have that usb controller built in or do they? if they did everybody would do stuff like that instead of buying expensive webcams right? would be crazy to use some ludacris multi camera from a Huawei or IPhone as a usb webcam. Do you think there is any way of making that reality? like with an external usb controller? but what kind of protocol do these modern cameras speak? is it something like those 15pin RasPI cameras? Please contact me if you are Interestet in this Topic and share your knowledge, I`ll be researching that topic because i really want to do something similar like you did here but with an actually good Camera. Btw. love your videos, keep it up!
I was just browsing and found this video and your comment....I did not had any intention to make a usb camera but after reading ur comment now I am interested 😂
Thats what I said too. He went out of his way to write down the resistance, but didnt say which was which, nor where they went. Kinda important, right?
This is been something I have a problem with anyone who claims they can use any pins on the camera module to USB conversion. It just doesn't work that way. I guess he meant to show the camera module number at the beginning from there he took down the numbers 12, 4, 16 and 20 for this module but he doesn't show the part where he supposedly read that from some module white paper. In any camera the control module has a make and model.. you can search for information on the web.
U didnt showed us which one is cameras power neagtive and positive and which were are data wires besides u took so much old key phone camera probably of some old 1.6 mega pixel camera and its output is like an hd cam?? U soldered all those camera wires randomly short circuting many wires with solder, and at they end u have used already sold in market otg cam, dnt fool us...
Hi! Your craft is very interesting! I am a deaf person and cant hear your voice. Can u give me an idea on how to recognize the connections of camera and what are the pin out should be connected? Can we use cameras from any various models of android phones? Hoping for your kind consideration. Thank u in advance!
yess. You must use a multimeter. The GND pin is very easy to find, because it's connected to the GND on the board. Pin V + connected to + 5V from the power IC. And D + and D- I found it by "Trial And Error Method". You will find it. However, not all cameras have usb communication.
Awe, no answer yet? Gee that’s too bad, I heard a rumor he’s doing a lot of perpetual motion machines and free energy videos now, breaking the laws of thermodynamics is mere child play for someone so gifted…. His fingers look so dumb. I just can’t help it, I have an incredible urge to slam them in a rusted out car door over and over again…..
Okay... so... you are saying that just connecting a sensor, without any logic involved, voltage regulators, or any other thing... and just guessing VCC vs +D and -D just work? Sorry, but its just too weird...
How did you seperate or analyze the input (data in ) output (data out) pin connections ...it is not clear ....and why did not use the right color code during soldering?
that depend on the model you get your hands on in most case but yes still a good idea for those that dont understant electronique much as hes not commenting xD
Well, great video but you should at least showed us in a schematic diagram where those wires are attached on the camera. I mean, we saw you solder those wires but we don't know which is positive, ground, data+ and data-.. I don't also understand how you traced the pins on the camera using the multimeter. If you could speak in your video explaining things would be very helpful.. Thanks..
Can I just attach a camera to an OTG flash drive and avoid knowing which camera has USB interface or not? I am just thinking. Thanks to whoever answers me.
HEHE BOI... i have like 3 broken phones ready to be used on something cool update: all of 3 have too much near terminals, wich will damage the camera and i will get mad and broke everything because i spend one week on that project, or it will just won't work and i will get mad and broke everything because i spent one week on this project :(
You connected the camera with 4pins, to usb. Then it would be vcc, gnd, data+,data-. Then what is the purpose of balance pin outs of the camera? Is it for focusing?. All camera from mobile phone this type of usb pin outs?...
Самое главное не показал. Паять и пользоваться термоусадкой мы и так умеем. Здесь много ума не надо. Лучше бы детальнее показал как понять какой провод камеры на какой контакт USB припаивать надо. А то что-то там прозвонил, что-то записал на бумажке. Хотя потом обрезал разъем и кому нужны эти номера контактов потом?
No first you have to break it apart remove vibration motor completely then speakers completely then find back lighting wires make mini switch to disable screen . This will keep you from getting cought.
that was a cool vid to watch but not sure why you wrote down the numbers on the pad ? also i have a challenge for you the nerf nightfinder scope is very basic IR scope the leds can be swapped out for better ones but the screen inside the scope is bad and the zoom is a digital zoom on a tiny pixel screen any chance you could look to improve it some how would love that vid and then i could copy to improve my own lol keep up the great work
Bro mere pass ek digital audio console hai 6 pin FireWire ki through computer mein ek card mein lagta hai...wo bhi 6 pin FireWire hai... Phaley console mixer computer mein software mein show hota tha...but ab nahi hota... Mujhey please guide ker dein FireWire ko Kasey check kru k Kiya problem hai.... Thanks
Демонстрация съёмки самоделки, один в один повторяет демо не самоделки!!! Даже мобила с подставки(той же самой) падает на том же кадре??!!! Однозначно - феик!
You must use a multimeter. The GND pin is very easy to find, because it's connected to the GND on the board. Pin V + connected to + 5V from the power IC. And D + and D- I found it by "Trial And Error Method". You will find it. However, not all cameras have usb communication.
@@simpletech3973 try all posibility combination.. try first wire . Error' try second wire..until. Successfully. Sometimes all error' then you unlucky :D
My camera only has 6 pins. very easy. If your camera has more pins. It will be very difficult. In the next video, I will give more detailed instructions.
also works with new cell phone cameras? Record one with a new cell phone camera, and I liked this video but if I don't have a viebo cell phone, how do I do it?
![Twenty One Pilots - The Line (from Arcane Season 2) [Official Audio]](http://i.ytimg.com/vi/XCz7WUotXs8/mqdefault.jpg)
Spy camera in a clock: ruclips.net/video/Ve16SuyXtTs/видео.html
📷📷📷📸📸📷📷📷qwgy
Hyeu ia te eu eu se
Can I make the car interior camera like this, but the DVR has a camera input, so they have a bns socket input
17:30 - Quick tip. Tape the camera down with some Kapton tape. Tape the four wires down close to where they will go also with Kapton tape. Hold them in place with tweezers to aid soldering.
Why you need spy camera 🤨 caught in 4k
I like how you were slow to tap the screen in sync with the recording that was playing on the phone to make this look legit
Mobile Phone camera modules follow MIPI protocol mostly. I wonder how you have managed hook it directly to USB. Please post a brief about interface topology.
real??
Lol isn’t the cellphone doing that?
Oh snap!
I like such funny videos BUT don't you dare insert these "hand made devices" in your PC or phone.It can damage it
For those asking how he found the camera pin connection diagram:
Using multimeter before removing the camera from phone motherboard, then
1. GND is very easy to find, it is shorted to GND of the phone
2. V+ is the 5V input from phone (this might be the hardest to find if you don't have experience in tracing the input voltage). Find pin that has no connection with the GND (but there might be more than one). The OP found out using diode test but does not show which one to test. Another way to find out 5V rail is to find the Power IC or Mosfet that gives the 5V to whole motherboard and find the direct connection. While the data lines are typically not directly connected to power rail (it has connection but has pull-up resistor like 10k Ohm) but directly connected to one of motherboard SOC leg.
3. Then the rest of D+ and D- are found by trial and error (using permutation).
First, the testing is done by soldering & jumpering the pins of the camera (while camera still attached in phone board) directly to USB and then PC as seen in 8:09.
And NOTE that only some cameras support direct USB interface. So, this will work only on few phone models.
And if you guess the 5V line wrong, you might permanently damage the whole system.
How did you find the other pins?
Ahh, the incisor wire stripping technique (off-camera). PRICELESS!
True. They are selfish. And the sad matter is they are many in RUclips
If I am not mistaken he used his teth as a stripper..:)
Stripping through mouth is a secret
i might need to learn this stripping technique for future to use on my future wife😏
It's amazing that used cellphones can be used in the hands of creative people like you.👍🇮🇩👍
i didn't find tbe schematic, how to identify the wires ?
good work👍
jajaja lol don't waste your time!
You know all the perverse uses that could be made using that thing, it's MAGNIFICENT!!!
:)
Great for finding out if something you've misplaced has fallen behind a dresser or book shelf without having to move it to see what's back there.
انت حقا مبدع رغم طول مدة المقطع ولاكن كل دقيقه فيه مفيدة جدا ويستحق المشاهدة
وحقا انت تستحق الشكر والتقدير
Owesome project 👍... What phone model and how did you find the usb pin???
What a fantastic video! Very well done! Up close viewing with the specifics. Written out what was needed to know. Very very well done!! Thank you for sharing this!
Wire diagrams would help us.maub fte some kind of directions to where to soder them on the camera.
Did he reply to you u
I need this to look inside engines to see burnt ir bent valves to show my customers.
Perfect.
Must do this project.
Great work! I thought I was the only one who makes things like this..plus great soldering job, especially not using a super fine point soldering iron! Those camera wires are damn hard to see and work with sometimes..Keep up the awesome work! Just subscribed..
@??0
Amigo, no encontre su trabajo en su canal sobre cámaras o micro cámaras, me puede compartir el links por favor, se lo suplico, muchas gracias...
Spy camera saya suka dgn karya Abang , sehingga menambah pengetahuan bagi saya pribadi dan masyarakat umumnya. Trima ksh ya ... Sdh membagi ilmunya
Jangan dicoba.
How did you know and find which are the connections of the camera from the pcb?
Try and fault i make one useing pc camera
Great project ,I would like to ask you how did you find which wire you need.And the wires function
x2
He will not answer your questio cos he fund the GND and Volt also + DATA and _ DATA 4 wires that you asked about that!!!
And with only a voltmeter no one can find them!!!
Otherwise you must a perfect of this monile board!!!
Mini spy camera in awasome
My query
1) does the mini spy cam for recording also for hours
2) where can we get the surface paper as used in this project
ใช้ได้จริงๆ ใหมครับ แบบนี้
Price?
I have a mic which is familiarly used with CCTV camera's.
I wanna use that mic as a external mic for videos.
4 wires are there... Shall i make it like this??? One side Micro USB & another side mic...
Do you prefer any app to record my audio if i made???
I will try and answer you.
What a good carnal video, a question, how do you know which pins to use?
Read a few comments below, I have instructed.
what do you think would be the latest (potentially best) phone camera with usb-controller built in? because i guess modern phone cams won`t have that usb controller built in or do they? if they did everybody would do stuff like that instead of buying expensive webcams right? would be crazy to use some ludacris multi camera from a Huawei or IPhone as a usb webcam. Do you think there is any way of making that reality? like with an external usb controller? but what kind of protocol do these modern cameras speak? is it something like those 15pin RasPI cameras? Please contact me if you are Interestet in this Topic and share your knowledge, I`ll be researching that topic because i really want to do something similar like you did here but with an actually good Camera. Btw. love your videos, keep it up!
I was just browsing and found this video and your comment....I did not had any intention to make a usb camera but after reading ur comment now I am interested 😂
I would like to know why you didn't show what wire to hook on the right path of ribbion
Thats what I said too. He went out of his way to write down the resistance, but didnt say which was which, nor where they went.
Kinda important, right?
Làm sao để xác định được chân vậy có thể hướng dẫn cho em xin với ạ.
This is been something I have a problem with anyone who claims they can use any pins on the camera module to USB conversion. It just doesn't work that way. I guess he meant to show the camera module number at the beginning from there he took down the numbers 12, 4, 16 and 20 for this module but he doesn't show the part where he supposedly read that from some module white paper. In any camera the control module has a make and model.. you can search for information on the web.
You are right because its doesnt work
@@АвазбекТухтамуродов-ь1н google is your friend. bt also an enemy of your time too lol
How do you know that you connected the wires from the camera to the correct wires tat the usb? Thanks for the video
U didnt showed us which one is cameras power neagtive and positive and which were are data wires besides u took so much old key phone camera probably of some old 1.6 mega pixel camera and its output is like an hd cam?? U soldered all those camera wires randomly short circuting many wires with solder, and at they end u have used already sold in market otg cam, dnt fool us...
You know that watching fake video is the waste of time...
Hi! Your craft is very interesting! I am a deaf person and cant hear your voice. Can u give me an idea on how to recognize the connections of camera and what are the pin out should be connected? Can we use cameras from any various models of android phones? Hoping for your kind consideration. Thank u in advance!
I will try and answer you
@@PhdHung thak u sir!
But how do you know the difference between the positive electrode and the negative electrode?
Thank you for the idea
You don't and he isn't going to show you either 😂😂😂😂😂
Hello my friend!. Do U know by the way, to make the same with an old blackberry camera? It's also good to know the pin values.
I will try and answer you
@@PhdHung Thanks a lot in advance!!!
What is the purpose of numbers you wrote in yellow paper? What is the pin of camera? Its like a pin of otg connector? (+ , Data -, Data +, -)
yess. You must use a multimeter. The GND pin is very easy to find, because it's connected to the GND on the board. Pin V + connected to + 5V from the power IC. And D + and D- I found it by "Trial And Error Method". You will find it. However, not all cameras have usb communication.
Bro I'm new one here ❤️, awesome video , can you show more clearly how to find out the pins of the camera
let's wait for the answer,,,
🤗🤗🤗
I hope he answers
Awe, no answer yet? Gee that’s too bad, I heard a rumor he’s doing a lot of perpetual motion machines and free energy videos now, breaking the laws of thermodynamics is mere child play for someone so gifted….
His fingers look so dumb. I just can’t help it, I have an incredible urge to slam them in a rusted out car door over and over again…..
Okay... so... you are saying that just connecting a sensor, without any logic involved, voltage regulators, or any other thing... and just guessing VCC vs +D and -D just work? Sorry, but its just too weird...
U r right
You right bro
yes this is not posible
It won't
@@krishnadasssv2733 no, without any kind of signals, Photo sensor could not be work.
How did you seperate or analyze the input (data in ) output (data out) pin connections ...it is not clear ....and why did not use the right color code during soldering?
Yes
Nice project but how to identify the wires in golden paper board?
What should be different about connection pins when connected to multimeter
Give a specific diagram for the wire connection to camera, that would help
that depend on the model you get your hands on in most case
but yes still a good idea for those that dont understant electronique much as hes not commenting xD
Siam ve chhin teh ang
I thei ta emm
My nem Suraj seni kya ap dosti karogi
Làm như nào để xác định các chân ?
Impressive eyesight and zoom from the cameraman.... As a fellow bot, I can relate to this
The finding pins is a mistery...
22:53 самые лучшие провода зачищенные своими зубами...🤣
Я всегда так делаю сам.
Wow without any module? Or driver board?
Well, great video but you should at least showed us in a schematic diagram where those wires are attached on the camera. I mean, we saw you solder those wires but we don't know which is positive, ground, data+ and data-.. I don't also understand how you traced the pins on the camera using the multimeter. If you could speak in your video explaining things would be very helpful.. Thanks..
Please read some comments below
Very Nice. Have to try this to I have thousands of old phones
How to know the connection of USB. cable and Camera
I'm confused
color coded
Red is + , black is - , green is + data , white is - data
Can I just attach a camera to an OTG flash drive and avoid knowing which camera has USB interface or not? I am just thinking. Thanks to whoever answers me.
HEHE BOI... i have like 3 broken phones ready to be used on something cool
update: all of 3 have too much near terminals, wich will damage the camera and i will get mad and broke everything because i spend one week on that project, or it will just won't work and i will get mad and broke everything because i spent one week on this project :(
I feel your pain man lol idk how the phone i use now isnt broken cuz this shit is infuriating sometimes, especially solder
You connected the camera with 4pins, to usb. Then it would be vcc, gnd, data+,data-. Then what is the purpose of balance pin outs of the camera? Is it for focusing?. All camera from mobile phone this type of usb pin outs?...
Only a few old cameras have USB connectivity.
Привет! Классно придумал👍 теперь нужно эту мини камеру подключить к wi-fi модулю.
ну ты поймей это не работает
Bravooooooooooooooooo, abs.respect, from the old BG.
Great idea i can keep the flash? Better for look inside de wall dreain pipes.
flash works at 12V :(
Самое главное не показал. Паять и пользоваться термоусадкой мы и так умеем. Здесь много ума не надо. Лучше бы детальнее показал как понять какой провод камеры на какой контакт USB припаивать надо. А то что-то там прозвонил, что-то записал на бумажке. Хотя потом обрезал разъем и кому нужны эти номера контактов потом?
you know the OTG pin is not like that.....it's self-deception...there should be 5 usb pins, one for jamper (-) so that OTG can be detected
What is a "jamper"?
No first you have to break it apart remove vibration motor completely then speakers completely then find back lighting wires make mini switch to disable screen . This will keep you from getting cought.
What was that thumbnail...🤫🤣🤣😂
Anyway good idea..
:))
lol
that was a cool vid to watch but not sure why you wrote down the numbers on the pad ? also i have a challenge for you the nerf nightfinder scope is very basic IR scope the leds can be swapped out for better ones but the screen inside the scope is bad and the zoom is a digital zoom on a tiny pixel screen any chance you could look to improve it some how would love that vid and then i could copy to improve my own lol
keep up the great work
سلمت يداك رحم الله الي يعلم بلا بخل ولا خفايا الله يبارك فيك
Bro mere pass ek digital audio console hai 6 pin FireWire ki through computer mein ek card mein lagta hai...wo bhi 6 pin FireWire hai... Phaley console mixer computer mein software mein show hota tha...but ab nahi hota... Mujhey please guide ker dein FireWire ko Kasey check kru k Kiya problem hai.... Thanks
How do i know the correct connection of wires?
Hi Thank You For Your Beautiful And Special Videos And Channel ❤️❤️💐💐
8:35 hello bro why you selected it in diode range? What pinouts you targeting at this point
Can you remote transmit the video to another phone or is the video stored in that cellphone Micro SD Card?
Great diy hack props to you Sir
😂What a beautiful idea. No component no IC. Excluding the important things, a beautiful spy camera was made.😝 Thank you😅
Bro its work are not
Hahahaha 😂
@@HariPrasad-ze7lw no
@@HariPrasad-ze7lw it doesn't work
@@bibhasmetia8592 aap check kiye kya bhai
Love it's where to buy black cord USB??
How to know the connection im confuse
Very nice !! do you sell them
Why is there someone else working in background....??.... Cool..!!!
A very nice device that should be installed at home for protection
muy muy bueno el video lo que me uvi9eragustado es que puedas explicar ..por partes sobre la camara saber mas
how do you find the output and input of the camera?
how to identify the wire terminals to make the cctv spy camera at home makes a video
Very easy
@@menatworkmw how
Which wires go where
very nice bro good work
Thanks
Would be easier with a much smaller tip when soldering small components together
Can you replace the usb with receiver for wireless transmitter with about 2km range?
Wireless SPY camera ruclips.net/video/4YGvEJBDBd0/видео.html
No
Karaoke star club stop
@@karaokestarclub4501 aáaáaáááááááaáaáaaaaááaaaaááaáaaaáaaaáaááaaaáaaááaaáaaaááaaaaaaaaaáááááaááááaaaáaáaaááaáaáááaááaáaááá
Add a demonstration video (a real one, like the thumbnail) otherwise this is clickbait, man lol
club ajs
Transporting old camera lens with an otg usb..
Wow..
Fantastic..
Great video. I love how you are able to get close up. I just subscribed. Love your work.
Which phone camera did you use please say....
It is a phone from China. Its camera only has 6 pins
I don't know what I am doing here I am just bored good luck with what ever that thing is
Super nice idea lods..thank you for sharing this video...👍😁
Thanks
I really like your pliers 😅 where did you bought it? 😂😂😂
:))
@@PhdHung answer his question ah
Wow awesome good work keep it up
☺😊☺👍👍👍👍
can you expland how to measure the + - data+ data- ? cause my camera is different with u
thanks before
The thumbnail is more like Simping ideas rather then Scientific...
I don't know how you could determine, USB positive wire ground abd data?
By the method of random attempts?
THANKS FOR THE NEXT THE BEST COMPLIMENTS BEFORE WATCHING THE VIDEO. ❤❤❤🙏.
Por favor explique en castellano porque si es muy interesante saber
@@dejanmedenica763hollo
Neither does he its fake video
Молодец, особенно порадовала быстрая зачистка проводов зубами.
Демонстрация съёмки самоделки, один в один повторяет демо не самоделки!!!
Даже мобила с подставки(той же самой) падает на том же кадре??!!!
Однозначно - феик!
А то что он прозвонил контакты на шлейфе а затем отрезал его нахрен не порадовало ? 🙂
I really liked,it thank you
I'll be impressed when you solder 6 uv LEDS + 6 IR LED's around the camera lens ;)
.....gratzi, chou!
And the prize for the most tasteless thumbnail of the year goes to........
Absolutely. Such a wonderful device for engineers presented bathroom spying. Have some imagination dude
@@pradeepkumarmsreedharan2814 hahahaha
?? you pervs clicked on it, so it worked! xD
Aaaaand the prize for the stupidest comment of the year...goes to....
@@hyperhektor7733 just clicked on it to comment about the thumbnail which "Clearly" has to be changed. Please dont assume that anyone is a "perv".
Sound: do you want to race with me
Video: okay...
Sound: haha I won
How did you know that the camera has the USB interface?
You must use a multimeter. The GND pin is very easy to find, because it's connected to the GND on the board. Pin V + connected to + 5V from the power IC. And D + and D- I found it by "Trial And Error Method". You will find it. However, not all cameras have usb communication.
@@PhdHung Thank you for advice, I will try myself.
Can explain what is Trial and Error method? I don't understand I am new about electronic
@@simpletech3973 scientific poke method
@@simpletech3973 try all posibility combination.. try first wire . Error' try second wire..until. Successfully. Sometimes all error' then you unlucky :D
Great work bro.
Thanks bro
wow. good job bro 😍
Thanks bro
Hmm bhai a66a...hay bohot a66a hay....
?
It is assumed that the colors of wires are bound together with numbering... thank you
My camera only has 6 pins. very easy. If your camera has more pins. It will be very difficult. In the next video, I will give more detailed instructions.
@@PhdHung Sir, it will be best if you explain it verbally.
Please.
@@PhdHung 66
is this real? how do you found the pins there is no make sence. please explain because i want to make one. and i dont want to waste mt time
You are doing great work 👍
Thanks bro
also works with new cell phone cameras? Record one with a new cell phone camera, and I liked this video but if I don't have a viebo cell phone, how do I do it?
Just simple and neat - Great