Milwaukee M12 drill repair LED wouldn't turn off
HTML-код
- Опубликовано: 12 дек 2024
- Summarized versions of most projects: www.swappart.com
LED Repair Tools:
Suction Cup: amzn.to/2KHz1WA
7/8" x 36" dowels: amzn.to/2I0NbAl
Cable Ties: amzn.to/2jEvfRB
GJ3C LED Tester: amzn.to/2FOluJf
LED Lens Adhesive: amzn.to/2wl6rao
Soldering Tools:
Hakko FX888D-23BY soldering iron: amzn.to/2rmflzj
1.6mm Flat Tip: amzn.to/2juY9U5
Cheap Hot Air Station: amzn.to/2KCWtEl
Recommended Hot Air Station: amzn.to/2rnRnTx
Hakko CHP 3-SA Straight Tweezers: amzn.to/2jwM1C7
Hakko CHP 7-SA Curved Tweezers: amzn.to/2rmleMV
Hakko CHP-170 Micro Cutters: amzn.to/2rmWJiV
Edson Desoldering Pump: amzn.to/2rm0KmE
Hakko FR-301 Desoldering Tool: amzn.to/2KEOkiX
Soldering/Desoldering Supplies:
Solder: amzn.to/2HRiW2L
AMTECH NC-559-V2-TF Flux: amzn.to/2wcldAd
NTE Desoldering Braid: amzn.to/2HWgbJx
Microscopes:
Recommended Microscope: amzn.to/2wg7KHF
Cheap Microscope: amzn.to/2rmRDSV
Cheap USB Microscope: amzn.to/2wepZNv
Diagnostic tools:
Fluke 87v Multimeter: amzn.to/2JTq23d
Fluke 117 Multimeter (cheaper): amzn.to/2FMQ4mv
Fluke Deluxe Probe Set: amzn.to/2HTCvHG
Cheap Multimeter: amzn.to/2HXe9ZN
ESR Meter: amzn.to/2HSHEQn
Semiconductor Tester: amzn.to/2FMQqJR
Bench Power Supply: amzn.to/2FLFU5u
Triple Output Power Supply: amzn.to/2KCLHxS
Rigol DS1054Z Oscilloscope: amzn.to/2HQQM7W
Variac w/ Isolation: amzn.to/2wdPbnx
50pc Test Lead Set w/Aligator Clips: amzn.to/2HRndmP
and omg how do you not go insane from that smoke alarm chirp?
Great comment. Add a lot!
I'm cleaning my drill... I come here because I have a piece fall out. The same piece that fell out at 6 minutes on the your video. Brilliant!
Hey man good stuff!!!
80% the videos out there doesn’t even go over this, you’re the only one I found.
Everyone one else just likes to hear themselves talk and stuff.
I know you’re not a pro but good job.
Great video. I was able to fix mine by spraying some electronic contact spray directly in to the trigger area without taking it apart. I sprayed liberally and pumped the trigger and it worked! Thanks. I would never have e thought of if.
Nice video. Opened up my M12- it was clean, no gunk. used an air duster to blow out any small particles. Bottom line: the light stayed on. I don't need the light. I exposed the diode by prying up the wires; clipped them, removed the diode and then, using a toothpick, dabbed some liquid electric tape on the exposed wires.
Problem solved.
support right to repair .no matter what you do farmer , tv repairman ,mechanic,iphone repair,ect. right to repair is important for us all
Great video. I had the same issue, I opened it up, cleaned it slightly and got it working normally again. The light only stays on for a few seconds after using it.
Thanks, I had the same issue and this fixed the problem. However I was walking around my house looking for which smoke alarm was chirping! 😀
Same about the smoke alarm 😅
Video out of focus most of the time btw
Quick version: Clean any build up on the PCB specifically, and be careful of the direction button bracing metal. I had this issue as well recently.
Using a aerosol can of brake clean or electrical contact cleaner would be more efficient to remove debris than a toothbrush with alcohol once you have it opened.
No definitely no brake clean, that thing melts plastic
Thanks! Your video saved my DeWalt. Had the same problem with the LEDlight but it works fine now after careful cleaning with isopropanol and a toothbrush. Greetings from Sweden! :)
I had to send my first one bac k, it worked randomly. The second one worked then after a few months it too began working randomly. The forward drill operation would falter, stop working and all four led battery lights would light up on and off. The only wat to get it to work was to flick it into reverse, pull the trigger ( and it would work ) then flick it into forward and it would work. Very disappointing
Just Googled mine, Got lucky and seen your video, I did same thing it fixed it, Thanks ..
Just replace the battery in your smoke detector!
That just happened to my drill. The light turns on but the drill won't work. Any ideas?
Same with my impact. Light on wont shut off and the drill dont work. I think somthing in the electronic crap is dead
I thought I put that brass piece in right next thing you know I snapped the brittle piece of plastic that tells the trigger what direction the Chuck should be going....if you don't remember the position it was in and pull a noob move like me you'll break it and end up buying a new drill on Amazon for 35 dollars
Idk how much I trust an electrician who can't change the batteries in his smoke detector
Thanks for the vid! Also, have you replaced the smoke detector battery yet? 😂
I'm going to break the light diode
leaf spring for the gear change 1|2 or direction switch
Electricians aren’t mechanics. That’s for sure!
Okay I'm watching your video to see where that little brass piece goes because mine fell out to and I didn't notice where it came from but I can't see very well can you please describe I put the drill back together but the brass pieces sitting out and I haven't tried to run it or anything I just put it back together so I wouldn't lose any screws Etc
Katy Klein Bottle what does the “brass piece” look like? It sounds like it may be the spring plate which goes down in a little slot in front of the forward/reverse shuttle.
Does anyone have a problem with the light going on an off every minute or twice a min
in case anybody else has this issue. The little brass clip is the spring tensioner for the forward/reverse switch. There's a little slot that one end goes into and the hump faces the black F/R switch. It puts pressure on the switch from the front of the housing to keep it in forward or reverse.
@@johng2880 thanks but my power tools were stolen a year ago
What size torx bit driver fits the screws?
Go find the answer yourself.
@@kevinhuberty5447 Fuck you Bitch
do some research
Okay I'm watching your video to see where that little brass piece goes because mine fell out to and I didn't notice where it came from but I can't see very well can you please describe I put the drill back together but the brass pieces sitting out and I haven't tried to run it or anything I just put it back together so I wouldn't lose any screws Etc