How to Test & Replace a Defrost Heater in a Refrigerator | Repair & Replace

Поделиться
HTML-код
  • Опубликовано: 10 дек 2024

Комментарии • 23

  • @awangrezalawangubi3376
    @awangrezalawangubi3376 3 месяца назад +2

    Thank you Sir,Helpfully content ,thank you so much for the knowledge .

    • @AmreSupply
      @AmreSupply  3 месяца назад +1

      You're welcome, we're just happy to help!

  • @kirkwilson7169
    @kirkwilson7169 5 месяцев назад +3

    Blessings and guidance thanks much your teaching is very informative I learn a lot.

    • @AmreSupply
      @AmreSupply  5 месяцев назад

      You're welcome, we're just happy to share some good information!

  • @lugs37
    @lugs37 4 месяца назад +2

    Thank you!!

  • @2005Pilot
    @2005Pilot 4 месяца назад

    Excellent!! Thank you 😁👍👍

    • @AmreSupply
      @AmreSupply  4 месяца назад +1

      You're welcome! We're just happy to share some good info!

  • @ZerihunBogale-k3h
    @ZerihunBogale-k3h 21 день назад

    Thank you

  • @DrN007
    @DrN007 Месяц назад

    Are you sure the Defrost Control is a separate switch in series with the Cold Control? Fridge thermostats are usually SPDT, so I don't get why your diagram has seemingly complicated the matter. Not to mention the shorting of L & N (your vertical wire mid screen) !!

    • @AmreSupply
      @AmreSupply  Месяц назад

      Thanks for watching. Most top freezer refrigerators that use a cold control thermostat will have a defrost timer, however some will have a defrost control board. The cold control thermostats in these models have 2 terminals and is a SPST which you can see here: www.amresupply.com/part/VB7-FROST-FREE-BEV-CONT
      The model we filmed this video with has a 2 terminal cold control thermostat and a defrost timer wired in the same way that it is in the video. In this model the compressor & fans could be turned on and off by manually advancing the defrost timer screw.
      Defrost timers have 4 terminals, and what is not shown in this simplified circuit diagram is the motor & resistor on the defrost timer. I can see why you'd think it would be shorted without an additional symbol to denote the motor. This is explained more in the defrost timer video:
      ruclips.net/video/rsv0ary__p4/видео.htmlsi=5IX68xC3YwbiFXhb&t=342
      More in-depth troubleshooting for the defrost circuit can be found here:
      ruclips.net/video/r2YUNLPs4kM/видео.html

  • @CharlesNgirazi
    @CharlesNgirazi Месяц назад

    Thanks alot

  • @carlosfernandes7203
    @carlosfernandes7203 4 месяца назад

    Muito boa explicação Carlos Brasil

    • @AmreSupply
      @AmreSupply  3 месяца назад

      Mucho grasias! Thank you very much!

  • @omarykajuna2552
    @omarykajuna2552 7 месяцев назад +1

    Nice

    • @AmreSupply
      @AmreSupply  7 месяцев назад

      Thanks for watching!

  • @medicman5278
    @medicman5278 4 месяца назад

    Also take care to not melt the plastic around the condenser if you are using a heat gun.

    • @AmreSupply
      @AmreSupply  4 месяца назад

      Yes exactly, that's why we recommend using a low heat setting. It will take longer but it will prevent the plastic from melting.

    • @terryhamilton5020
      @terryhamilton5020 Месяц назад

      ​@@AmreSupplyf tr😮.

  • @freedomisfromtruth
    @freedomisfromtruth 4 месяца назад

    Do you ship to the US or have a US depot?

    • @AmreSupply
      @AmreSupply  4 месяца назад

      Thanks for watching. We are based in Canada but we do ship to the US!