very helpful Video As Usual. I see the problem like offsetting the I/O Addresses for 0 to 10 and you should do the same for AI addresses on PLC , because the floating voltage on TIA Portal is coming from the PLC I/P not from Factory I/O. I am learning from your good videos along with Rajvir Singh videos at the course..
Yes. The analog signal messed me up for a while. I often overlap various words in my programs as they get larger as well. Reinforces the fact that we should create a spreadsheet for all bits, words, and dwords as we develop our programs. Thanks for helping me learn as well.
You are make mistake about ID100 because. You setup your analog imput on PLC 1200 on start IW100. In program starting reading your analog input 0-10V not from factory I/O but from PLC and even not corect becouse from PLC going anlog synal intiger and occupying one word.Thanks for lesson. This program is very nice for beginer and I can learn and practice.
3 года назад
7. Let's start with FACTORY IO || Bắt đầu với phần mềm Factory IO ruclips.net/video/k6fmdcjFPRI/видео.html 4. Pick and Place XYZ in Factory IO and PLC || Tay gắp 3 trục XYZ trong Factory ruclips.net/video/neKIDf9H8tg/видео.html 3. Level Control Analog in Factory IO and PLC || Lập trình ĐK mức chất lỏng ruclips.net/video/L8TiwOX_d3E/видео.html
Your previous video NORM_X use Int to Real such as %IW64 (Range from 0 to 27648) but why in this video you use Real to Real and fill with %ID112 which range is 0.0-10.0? How about %IW112 but Int to Real and 0-27648???
Here is a link to purchase Factory IO. (Note: this is an affiliate link for my channel) factoryio.com/url-action?ref=petervree Full Siemens TIA Portal PLC Programming Course available here: petevree.thinkific.com/courses/siemens-tia-portal-plc-programming Playlist Link for further videos: ruclips.net/p/PLyL0ResmI4Q2Rz5wtTKWhKhFMLnWU1n6Q
hello pete. i am confuse to solve this problem in factory io using s7-300 cpu. do u mind to make a brief discussion about this tank level that is ID100 ( real ) because i am using comparators command ( dint) because if i use real it turns red. thanks
Network 1 was just a simple 3-Wire control that turned on a "Sys Run" Bit, that controlled a green and red light. Here is a new video that might explain things better: ruclips.net/video/T9kPdUtWZZw/видео.html
The simulation software is Factory IO, a phenomenal program. link: factoryio.com/?gclid=CjwKCAjw1rnqBRAAEiwAr29II1x5J53juTC3-Htk_tGQqbKrj7OD0XX32vu4V6cThat3FdNDSgHH6hoCfA0QAvD_BwE
Hi, pete, I have watched alot of videos and I can say you’re one of the best. You explained the steps for every zeroes like me can understand. Thanks
You are making a great effort. Thank you so much.. 🌼
Thank you Pete for all of your videos :)
Thanks bro, it was very clear!
BEAUTIFUL
Very Useful! Thanks!
Thanks for all the nice comments. Glad the videos are helpful.
Beautiful
very helpful Video As Usual. I see the problem like offsetting the I/O Addresses for 0 to 10 and you should do the same for AI addresses on PLC , because the floating voltage on TIA Portal is coming from the PLC I/P not from Factory I/O.
I am learning from your good videos along with Rajvir Singh videos at the course..
Yes. The analog signal messed me up for a while. I often overlap various words in my programs as they get larger as well. Reinforces the fact that we should create a spreadsheet for all bits, words, and dwords as we develop our programs. Thanks for helping me learn as well.
You are make mistake about ID100 because. You setup your analog imput on PLC 1200 on start IW100. In program starting reading your analog input 0-10V not from factory I/O but from PLC and even not corect becouse from PLC going
anlog synal intiger and occupying one word.Thanks for lesson. This program is very nice for beginer and I can learn and practice.
7. Let's start with FACTORY IO || Bắt đầu với phần mềm Factory IO
ruclips.net/video/k6fmdcjFPRI/видео.html
4. Pick and Place XYZ in Factory IO and PLC || Tay gắp 3 trục XYZ trong Factory
ruclips.net/video/neKIDf9H8tg/видео.html
3. Level Control Analog in Factory IO and PLC || Lập trình ĐK mức chất lỏng
ruclips.net/video/L8TiwOX_d3E/видео.html
Hi again Pete, do u think u could do a complete video of ur assembler manual control ? Thank u sir. Regards Felix
But you don't have QD112 in the plc so it should be an error
Hi Pete i can't find it but did you ever make a PID control for this
In the online course that I am currently selling.
Your previous video NORM_X use Int to Real such as %IW64 (Range from 0 to 27648) but why in this video you use Real to Real and fill with %ID112 which range is 0.0-10.0? How about %IW112 but Int to Real and 0-27648???
Hello sir is there any issue to install this software with my windows10 HOME
Here is a link to purchase Factory IO. (Note: this is an affiliate link for my channel)
factoryio.com/url-action?ref=petervree
Full Siemens TIA Portal PLC Programming Course available here: petevree.thinkific.com/courses/siemens-tia-portal-plc-programming
Playlist Link for further videos: ruclips.net/p/PLyL0ResmI4Q2Rz5wtTKWhKhFMLnWU1n6Q
hello pete. i am confuse to solve this problem in factory io using s7-300 cpu. do u mind to make a brief discussion about this tank level that is ID100 ( real ) because i am using comparators command ( dint) because if i use real it turns red. thanks
are the contents of network 1 necessary to start the tank fill proces and discharge valve process? you didn't share network 1☹
Network 1 was just a simple 3-Wire control that turned on a "Sys Run" Bit, that controlled a green and red light. Here is a new video that might explain things better: ruclips.net/video/T9kPdUtWZZw/видео.html
Hello Pete, although the Rajvir Idea has worked, still didn't get why that input didn't get the value from Factory IO ?
Not sure why that conflict happened either.
may i know what software you used for your 3d presentation?
The simulation software is Factory IO, a phenomenal program.
link: factoryio.com/?gclid=CjwKCAjw1rnqBRAAEiwAr29II1x5J53juTC3-Htk_tGQqbKrj7OD0XX32vu4V6cThat3FdNDSgHH6hoCfA0QAvD_BwE