Great video thanks. Very thorough and to the point and I don't have to listen to blabbing about topics that are irrelevant when I'm under the hood sweating my balls off.
Dear I did not see this part, would of done lower part if know before changing injectors, but can that be my problem of sometimes #4 & 6 misfires?, fixed my EGR connection, but still my PVC tube still BLAST OFF with smoke :(
By chance do you know the part number for the the two O-Rings on the fuel pressure line that you are disconnecting with the 5/8 fuel line removal tool?
I got the 2003 escape with a mystery water leak under intake , next to top motor mount . no water in the oil , runs good . Cant seem to locate , any ideas ? anybody ? I would be in a good mood if someone knows . Lol .
LOL...it's a Ford, David. It's a "guinea pig" Escape with a blown engine, just for vids. It's been cleaned up a little, and hasn't been driven in a while. Thanks for watching!
@@GreaseMonkeyFever Ah, that's why! They don't leak if they don't have oil! Lol The 4 cylinder for this car was actually made by Mazda, but the 6 cylinder is Ford's doing. I actually watched this because I had to change my Coil Packs in the back. After I buttoned it up, 5 minutes later the alternator died, so I'm going to pull it back apart and pull the alternator through the top. I saw most videos took the passenger drive axel out and removed it from the bottom, but if the intake manifold is out, I'm pretty sure it's an easy lift.
G.m.f. hey guess what! I'm back!!!! U would not believe what I just went through??? In the ur last post and because u r so slow! I ended dying in the nursing home, yeay,really, big time bummer! And now I have been reincarnated and I am 14 years old again!
It would b a good time to change out that pcv valve with the lower out 😉... nice vid BTW 👍👍
Great video thanks. Very thorough and to the point and I don't have to listen to blabbing about topics that are irrelevant when I'm under the hood sweating my balls off.
Looks like a lot of hassle. I have to do my wife’s car today not looking forward to it. Thanks for the video.
Great Job 👍
Dear I did not see this part, would of done lower part if know before changing injectors, but can that be my problem of sometimes #4 & 6 misfires?, fixed my EGR connection, but still my PVC tube still BLAST OFF with smoke :(
By chance do you know the part number for the the two O-Rings on the fuel pressure line that you are disconnecting with the 5/8 fuel line removal tool?
What are those golden like bolts called built into the intake manifold?
What might be the problem if I open up the oil dip stick of the engine it then suddenly dies?
Its not ncessery to remove the fuel rail from its main line you can just wiggle it and lift
I got the 2003 escape with a mystery water leak under intake , next to top motor mount . no water in the oil , runs good . Cant seem to locate , any ideas ? anybody ? I would be in a good mood if someone knows . Lol .
*Like !!!*
Amigo tengo una ford escape xls v6 2002 ya cambie bobina y bujias y los inyectores y tiene un fallo que de decompression no funcionan las bujias 2 y 6
Me is is 4 & 6 misfires :(
I got a 2003 Ford Escape v6 but every time I got it and drive turn the AC the RPM gauges bounces up and down and wants to die almost
Justin Edwards could be idle air control valve
www.rockauto.com/en/catalog/ford,2003,escape,3.0l+v6,1414437,fuel+&+air,throttle+position+sensor+(tps),5136
Amazing, I don't see gallons of oil coating the oil pan... is this really a Ford?
LOL...it's a Ford, David. It's a "guinea pig" Escape with a blown engine, just for vids. It's been cleaned up a little, and hasn't been driven in a while. Thanks for watching!
@@GreaseMonkeyFever Ah, that's why! They don't leak if they don't have oil! Lol The 4 cylinder for this car was actually made by Mazda, but the 6 cylinder is Ford's doing. I actually watched this because I had to change my Coil Packs in the back. After I buttoned it up, 5 minutes later the alternator died, so I'm going to pull it back apart and pull the alternator through the top. I saw most videos took the passenger drive axel out and removed it from the bottom, but if the intake manifold is out, I'm pretty sure it's an easy lift.
G.m.f. hey guess what! I'm back!!!! U would not believe what I just went through??? In the ur last post and because u r so slow! I ended dying in the nursing home, yeay,really, big time bummer! And now I have been reincarnated and I am 14 years old again!