How to use: 1 Channel DC12V Remote Control Switch with 2 button remote control
HTML-код
- Опубликовано: 10 янв 2017
- 433Mhz Universal Wireless Remote Control Switch DC 12V 1CH relay Receiver Module and RF Transmitter 433 Mhz Remote Controls 1527 with 2 button
From:
www.aliexpress.com/store/prod...
Link from DE: www.amazon.de/dp/B081CD9GHD
About Working mode:
About Working mode:
1. Momentary/Jog: Press and hold -- on; Release -- Off
Keep pressing one button , the corresponding channel is working /on;
Loosen your finger is stop/OFF .
"4 channel switch"receiver" need 4 button remote control "transmitter "
2. Toggle/Self-Lock: Press -- on; Press again -- Off
Press one button for one time , the corresponding channel is working/on;
Press the same button again is stop/OFF .
"4 channel switch "receiver" need 4 button remote control "transmitter" ".
3. Latched/Inter-Lock: Press -- on; Press other button -- Off
Press one button for one time, the corresponding channel is working/on;
Press another button is stop/OFF"At the same time, another corresponding channel works" .
" 4 channel switch " receiver" need 4 buttons remote control "transmitter".
Clearing the code :
Push the learning button on the receivers for 8 times , the codes will be cleaned .
After clear the code, all the remote control cannot work any more.
Learning the code :(momentary)
Push the learning key on the receiver once time , it comes into momentary setting mode .
Wait for a moment , the LED will be off , it comes into learning state .
Push the remote button , LED indicator on the receiver board will flash then come off .
After 3 seconds, the LED indicator will be on again , learning successfully .
Learning the code : ( Toggle )
Push the learning key on the receiver twice time , it comes into toggle setting mode
Wait for a moment , the LED will be off , it comes into learning state .
Push the remote button,LED indicator on the receiver board will flash then come off.
After 3 seconds , the LED indicator will be on again , learning successfully .
Learning the code :( Latching )
Note: When you choose for latching mode , in order to learn more remote control , you need to learn two different button , the first time learnt is for "ON", the second time learnt for "OFF".
For example : button A = ON , button B = OFF
Push the learning key on the receiver triple time , it comes into latching mode .
Wait for a moment , the LED indicator on the receiver board will flash then come off.
Push the remote button A .
LED flash for 5 times .
Push the remote button B .
Led flash for 5 times .
After 3 seconds , the LED indicator will be on again , learning successfully.
A = ON , B = OFF .
Learning the code :( Time delay mode )
Push the learning key on the receiver forth time , the time dealy for 5 seconds .
Push the learning key on the receiver fifth time , the time delay for 10 seconds .
Push the learning key on the receiver sixth time , the time delay for 15 seconds .
The LED indicator will be off .
Push the remote button , LED flashes and off .
After 3 seconds , the LED indicator will be on again , learning successfully . Наука
Super bien expliqué même sans parole !!! merci
Great tutorial! Thanks. I use mine with two remotes in the latch mode. Works great!
Köszönöm! :-) Végre be tudtam állítani self-locking módba!
Thank you so much for making this!😃
Thank you! The instruction for adding a second remote worked perfect.
I only see one remote being programmed?
Thanks a lot! The user guide didn't tell how to erase the codes. Also the programming looks so much easier when I see it in video. The guide was not very clear because it was auto translated from Chinese. This was very clear video and had nothing unnecessary but pure facts.
At the start of the video, there are code clearing guide. When we press the learning button 8 times, after the LED flashes. The code is cleared.
Great work.....Thank you for the video
Muchisimas gracias, bien explicado, simple y practico.
It's working thank-you very much
Muchas gracias. He visto bastantes vídeos sobre esto, pero tan comprensible como esté muy pocos.
great tutorial and very simple to understand......and multilanguage....!!!
Why don't these video ever show the power source
ruclips.net/video/QuFzDcIiDxQ/видео.html
It's simple the black wire going up is ground, the orange is power
I guess it's implied that if you are asking about a power supply you would know that you could use battery or a power supply and would know how to hook up already I guess like if we were in algebra they would assume we already know how to perform subtraction and addition
Excellent description.
Very helpful, thanks for the video
This worked perfectly on a similar system! Thanks a bunch!
Thank you
@@qiachip RANGE ? (will it work from another room 10-15 feet away?
Muchisimas gracias, bien explicado, simple y practico
GOOD job. your video helped me a lot because the receiver i purchased didnt come with very good instructions.
if you are looking to purchase remote controls again, you can always check out rodot.aliexpress.com/store/1456073?spm=2114.12010108.nav-home.1.411a2c9fdP5gEr or qiachip.com/
thank you so much for this information
Thanks! I bought the card after watching the video!
Thanks!
it's garbage it does not learn any RF i tried two different remotes and it won't learn any RF , i used a PT 2262 and other remotes it will not learn any of them i know they are 433MHZ and it will not learn them
Yes, this product has been eliminated,
Great video. Thanks for sharing.
всё чётко, и...спасибо!
I have 12 v leds pre wired but I’m looking to set them up with a remote and battery power any advise?
bought one of those different brand though, horrible instructions but was able to figure it out, using it to turn my power inverter on
Think u very much, i found you and the guide how to reset my module.
Gracias amigo por tu video interesante.
Easily understood. i like latch mode.
Muchas gracias, ya me tenia aburrido.
Можно ли запрограммировать, чтобы включение происходило от длительного нажатия или от двух, трех нажатий. Т.к в кармане часто нажимается само по себе.
Can anything be done to the antenna for longer reach
THANK YOU!
Can you make a vid on how to wire it?
very helpful video... thanks 🎉
Wow.good experiment
muito bom!
thank you very mush
Good man, great video, cheers for your help
Thank you for the helpful programming modes! Mine doesn’t come with instructions
Hi, I have the same relay module as you.
When I try to make it learn a code I press the button 8 times, so it resets, then I press it once to activate toggle mode.
when I press the remote button the light doesn't blink but it only turns off and the card doesn't learn the code. What should I do?
Holding 8sec to erase codes worked for me.
Thanks 👍
can use for delay off ?
Can i use this for 36v kids quad? Need this for safety , thanks
Sat Sri akaal my friend. I hope I spelled that right lol.
Can u show how the wiring is attached please
Спасибо.
Muito bom...
Parabens pela aula.
Thanks! good student!
Thanks👍👌
Есть ещё режим таймера,
1) это 4 нажатия кнопки на реле и настройка пульта на включение на 5 секунд.
2) 5 нажатий, на 10сек.и
3) 6 нажатий кнопки реле, на 15сек.
По истечении времени реле отключается автоматически.
К реле можно привязать до 50-ти пультов
Сбросить все пульты можно зажав кнопку на реле на 8 секунд до загорания индикатора на реле, или как в видео нажатием 8 раз на кнопку на реле. 🖐️😉
У меня не сбрасывается зажатием ни на 8 секунд, ни на 5, как написано в руководстве. Только 8 нажатий
Can I wire this into a cars fuel pump wiring?
You are doing what I want to do, But I need to know the wiring to 'NO Com NC V- V+'. Can you show that????
Please tell me where
find a 220 volt remote control in which there is one channel but only with an independent contact. MEET that with the help of the remote control it was possible to connect the break of an independent circuit.
Can you show your wiring setup please
Gracias👍🏻👍🏻
Muy bien y gracias
谢谢
Hola! Lo he conectado al telefonillo de mi casa. Pero cuando abre hace un ruido un poco raro. Supone algun problema? Gracias!
Vous pouvez montrer le branchement ? merci
does it work with an input of 2.5A will it have an output?
Thx
What is the wiring steps for this? Thank you
How much power can it handle? Car horn?
Y como le hago para darle corriente para que este encendido tiene muchos cables?
Excellent post. Thank you so much! Is there a setting when you click 7 times?
Yes, it will delay 20s to turn off the relay
Спасибо без слов но всё понятно👌👌
🎉🎉supar supar 🤝
Amazing
Hi. Can be fitting to bmw car ? To stop steering 😢? Thanks
Hi if I don’t know how to connect them how will I know how to program them?
Hello can I used with normal AC Adapter with 12V === 1.5 A or the 1.5 Am is to much thanks
I wanted to ask you for advice. I have connected a Normally Open electrometallic lock to this relay but I would like to add a led that lights up when the lock is not in action.
Do you want the state of the lock to be the opposite of the state of the LED you added?
That is, when the lock is powered off, the LED turns on; when the lock is powered on, the LED turns off. Is that correct?
Can it work with 9v battery or 12v battery?
can i use whitou control? i want to use with radio baofeng, wil work?
What does the wiring look like to control two separate leds with A and B buttons? Can you show that? Thanks
did you get answer?
Why the device suddenly turn off without pressing remote button?
Please help!
Is it possible to clone 2 remotes in a 1 channel ?
Can this open cars
What frequency is this?
Hallo, i have a question.
Could i use this as a kill switch for my motorbike?
Lets say to cut the line from the plus of the battery to store the bike when shopping or something and put the second button to start the bike from distance?
I have a mecanical kill switch and at the other side a mecanical engin starter switch.
I would cut the wires and pass them true this device.
So that i could use the orignal swtiches when the remoute switch is on ON for the main power.
Thank you
Hi did you use this for that in the end
hi new friend supporting you
What is wire schema for momentary? please provide.
It is hard to type out the wire schema. But you can check out www.aliexpress.com/store/product/433Mhz-Universal-Wireless-Remote-Control-Switch-DC12V-1CH-relay-Receiver-Module-and-RF-Transmitter-433-Mhz/1456073_32716729232.html for a more detailed descriptions
I put my receiver on 24v 26v but don’t work only flashing lights but relays don’t work can u tell me what adapter you guys using or were to get power from also try battery charger 24v and did work but can’t use battery charger all the time??!
12V adapter
I have 2 autogate door..button a for 1 door open/close..then button b for open/close 2 door..how to setting
Set Toggle Mode.
Sería mucho pedir el diagrama de instalación deseo conectar unas luces led para mí auto
Real range?
BOM DIA EU TENHO UMA AUTO ESCOLA INSTALEI NA MOTO FUNCIONOU PERFEITAMENTE MAI EM MOVIMENTO C O ALUNO APAVORAR E ACELERAR ELE NAO FUNCIONA COLOQUEI NO POS CHAVE VC PODE ME AJUDAR
is there a small battery source I could use to hold open a servo that would work exactly the same as this but a small portable battery source?
I used a battery case with 8pcs 1.5V batteries.
Did you try an a23 battery it's a tiny 12v battery found at any shop or supermarket
Any ideas for a wiring diagram! I'm stuck I'm trying to use a solenoid for a door lock to work on this device ?
Zaheer Sarwar you can scroll down from this page for wiring diagram www.aliexpress.com/store/product/QIACHIP-433MHz-Universal-Wireless-Remote-Control-Switch-DC-12V-1CH-RF-Relay-Receiver-433-MHz-Receiver/3681001_32862095630.html remember to use your computer to open the link for the diagram
The more practical approach would be wiring the com with - then plug in the power source on + and - once it’s done just plug in your lock, plug in your lock + to NO and - to -
@@qiachip excellent this has worked for me. Thank you for your help!
Zaheer Sarwar no problem, feel free to ask us anything about our products
@@qiachip can I power this using lower voltage like 5v??
Can this circuit board power a 12v golf trolley.
Yes, it’s most likely 12v 10a
Can yuu make it always be on unless triggered off?
Yes, of cause you could select Mode 2 toggle, in this mode you press to turn on, and then press to turn off.
Thank you
ru.aliexpress.com/store/product/433Mhz-Universal-Wireless-Remote-Control-Switch-DC12V-1CH-relay-Receiver-Module-and-RF-Transmitter-433-Mhz/1456073_32716729232.html
Quando desernegizar o rele de acionamento, ele perde a configuração em q foi feito? Tera q configurar novamente?
Olá, não há necessidade de reconfigurar
Thanks a lot for this tutorial that save my life. Just, on mine (AK-RK01SY), for the reset I have to maintain the switch until the led flashes instead of pressing 8 times.
its work🙂
I have two of these remote control units can I use one remote control to control both of the PCB boards as I would like to use a button for one board and use B button for another board is this possible
Yes, you can use it like this.
Como adiqueri
Como comprar
B shall be the same key and A key way of learning
The video demonstrates three "working modes" settings.
Can I also use this to operate a CDI unit on a scooter?
I am not sure about this, you can try
To com um rele desse e queria liga uma mini trava soleide essa ligação e a mesma do vídeo
Do you want my circuit picture ?
Range ?
do you have a wiring diagram please?
Yes! We must to be need,you can see some wiring diagram by www.amazon.com/dp/B07GJT1D1Z?ref=myi_title_dp,so good product 😉