Dear I have a project with two motors one use for up and down and second is for left to right, for dish Receiver for Satellite Tracking.. may I use these modules???
how to control 1 servo and 1 dc motor using l293d motor shield at same time. I watch many video on l293d shield but in all video different motor not run at same time . For example if there is a code for dc motor than you can run only 4 dc motor. If there is a code for servo motor you can run only 2 servo. But I want to run servo and dc motor together using l293d motor shield. So sir please provide me code for running two different motor ie..Servo and Dc motor same time.
Thank you very much I worried a lot to use L293d motor driver with my project because of insuffient information of power supply But this video provides a great detail of different means of using power supply with this motor shield
Sir can i use four 1000 rpm dc motors with 12v supply in this motor shield? With out facing the heating problem? Because sir i am using a L298N motor sheild but it was heating in 3 seconds like fire Please help can i use L293D instead of L298N?
bro I have connected all four motors to the motor driver shield but connected only 3.57 volt battery and the tyre is not moving is this a battery problem for my motor driver shield is not responding please help me
I have been trying to run 4 motors , but it's going to slow down at very faster with seperate 9v arduino powerup and external power supply of 12v , can you please help me. motor power supply range 3v-6v
Bro till how much mah battery we can plug to motor driver shield bro can I use 4.2 v 6000 mah battery of 2psc is the motors works good bro plz give me a solution bro plzz
English accent is too good!!! 🔥👍
Even with the jumper out.. when i supply 12 v to sheild .. arduino gets fried
How many 12v Turbine gear motor can connected to motor shield ?
Dear I have a project with two motors one use for up and down and second is for left to right, for dish Receiver for Satellite Tracking.. may I use these modules???
can we use mg995 servo and 4 gear motors of 300 rpm to l293d shield?
Can we use this driver with esp32?
how to control 1 servo and 1 dc motor using l293d motor shield at same time.
I watch many video on l293d shield but in all video different motor not run at same time .
For example if there is a code for dc motor than you can run only 4 dc motor. If there is a code for servo motor you can run only 2 servo.
But I want to run servo and dc motor together using l293d motor shield.
So sir please provide me code for running two different motor ie..Servo and Dc motor same time.
Thank you very much
I worried a lot to use L293d motor driver with my project because of insuffient information of power supply
But this video provides a great detail of different means of using power supply with this motor shield
which type of dc motor do u use?
Sir can i use four 1000 rpm dc motors with 12v supply in this motor shield?
With out facing the heating problem?
Because sir i am using a L298N motor sheild but it was heating in 3 seconds like fire
Please help can i use L293D instead of L298N?
Well yes you can!
It supports 12v
L293D engine hood problem. Output voltage in m4. 7 volts, and the rest of the outputs are 2 volts😢
sir , but moters connected to diver moter shiled is not working, plz reply
Can i connect bluethhot module
Sir when I tried to compile code it shows message (FATTAL ERROR AFmotor.h) nosuch file or library .what is reason?.
Yes I'm also facing this problem
af motor library install karna padta h
If I want to add joystick, how??
can we set the road back and forth 10 minutes forward 10 minutes. and set the speed
How many volts is your dc motor?
bro it getting error in complation dc_motor_test.ino:23:6: error: 'void loop()' previously saying like that plzzz give me solution for it
Can ardunio be given 12v 2amp Or only 5 to 9v supply
bro I have connected all four motors to the motor driver shield but connected only 3.57 volt battery and the tyre is not moving is this a battery problem for my motor driver shield is not responding please help me
I think your supplied voltage is not enough.
I have been trying to run 4 motors , but it's going to slow down at very faster with seperate 9v arduino powerup and external power supply of 12v , can you please help me.
motor power supply range 3v-6v
How I connect HM-10 Bluetooth module when using this L293d arduino motorsheld?
Is L293D fits with ardrino uno Atmega 328p
Recommended battery to connect 4 BO Motor with L293D ?
I am having 2 numbers of 18650 battery as of now!
If I would use two servos and I give power to Arduino with the USB, can I use a battery pack to power the servos ?
Bro till how much mah battery we can plug to motor driver shield bro can I use 4.2 v 6000 mah battery of 2psc is the motors works good bro plz give me a solution bro plzz
can i connect 4 dc motors and one servo? if not, then can i connect 4 dc motors in two slots (m1 and m2), and one servo, as i am making a 4 wheel car
Help me , why my obstacle avoiding car not motor not working ?
How can I connect a bluetooth module on this device? I want to power it using bluetooth. Thanks
Just Connect rx and tx Pin to Pin no. 1 and 0 respectively and Power you can supply with the servo Gnd and positive pins
can i run the motor using digitalwrite ?/
what is the model of this dc motor ?
Very informative video bro....All done perfectly 🥰
Great explanation. Thank you.
Thanks bro,, take your efforts.
Very nice, very useful video for beginners.
luv u bro 🤰👸👸👸🤰🤰🤰🤰🤰🤰🤰🤰🤰🤰🤰♑
does this code allow for turning?
Using the 9V battery is not good using a 3.7volt lithium ion battery in array of 2 is better
Sir , motor driver shield me motor laganese L293D IC heat kyu hota hai
mera bhi hota h
Hi, does anyone know if I can use 4 DC motors and 1 SERVO motor at the same time? Thank you for answering
Yes you can
Why the speed of the motor is slow ?
search for the needed voltage for your dc motor and use a power supply with that voltage to power the driver shield
The library that your mintioned is old
Can I connect 4 dc motor and 1sevo at one time
yes
Can this library will be compatible with arduino mega?
yes
Can this used on IOT?
Me ek project bna raha hn kia ap meri us me help kr skte hen...
How cost
Boa tarde amigo daria para acionar o Children Como esc para acionar motor brushless bifásico ou sejá três fios.
When I unplug it from the computer it stops working.
I
thnks bro !! your video was of great help
Can you do a video showing how to control 4 motors via Bluetooth??
Can we make flying drone using this sir
no, you have to use BLDC motor
sir i mean...can we use this board for making drones
Can I use it with other litter T,L
Boa tarde amigo daria apaixonar um motor Brushless porque nunca vi ninguém acionando neste motor
are u assamese??
أهلاً وسهلاً ومرحباً بك-يتعذر الاشتراك ولا يوجد جرس-يتعذر الاستجابة لكل طلباتك-شكراً لك-يتعذر التعليق- لا أعلم .
Did anybody else worry he was going to fry something on the shield when he was sweeping the 9V leads across it?
Great, Thank you.
Hi, if i use 8 motor. And the output of L293d is only 4. Can i put 2 motor in 1 output? Event it run at same time..
Yes bro, It works. I tried only when 3 batteries in parallel( parallel con adds current) for me. I used 9v battery
Thanks man!!
thank you so much
Super
thanks bro
thankyou
😮
😂
Video no t claer
Sir , motor driver shield me motor laganese L293D IC heat kyu hota hai
Can i connect 2 dc motor and 2 stepper motor?
thank u very much