Комментарии •

  • @donvukovic7440
    @donvukovic7440 Год назад +11

    I have been soldering for over 60 years and this is the first time seeing this. Thank You for this video.

  • @Swenser
    @Swenser 5 лет назад +8

    looks like top notch low melt solder and great iron and tips. no problem with destroying parts. I'm a butcher. I use crappy solder, irons, and flame gas torch to get stubborn pieces off. One day, I'll learn to use quality equipment for a good job, but for now. I'm a chop shop butcher. Thanks for inspiring to do a more pro job.

  • @pdrg
    @pdrg 6 лет назад +33

    Hadn't seen the copper wire trick before, kudos, that was clever. And I like that all the players got to take a bow at the end ;-)

  • @manupaksimanjuntak9587
    @manupaksimanjuntak9587 3 года назад +19

    I have 13 years of experience and are very used to soldering and desoldering and actually don't need to use a wide or elongated desoldering tip like in the video, just use a sharp tip. SMD components have 2 to 18 pins that can be removed easily, there are several components such as 8pin is opened by heating the body of the actual component is not recommended, but if the component is definitely damaged it is not a problem, but don't do it on good components

    • @berfava
      @berfava Год назад

      What products do you use besides the hot iron? I'm having a hard time to remove lead free soldered components just with the iron

    • @za_ozero
      @za_ozero Год назад

      Even if the part is not working the board most probably is. Hot air gun costs times less then one supermarket trip

  • @neilaldenarmstrong9806
    @neilaldenarmstrong9806 4 года назад +5

    The copper wire trick for the micro USB connector is brilliant and now permanently stored in my mental flash memory! Thanks!

    • @DrZipZwan
      @DrZipZwan 3 года назад

      yes and no! Dont do that in case u intend to resolder that USB connector somewhere else cause, USB connector got plastic parts thats gona melt... or to not heat it much...
      What I do, I first desolder holding left and right pin that fixe the connector to the PCB, then desolder the rest 5 Pins, this why if it is done well the connector can bere-used 😉

    • @phr3ui559
      @phr3ui559 4 месяца назад

      @@DrZipZwanok

  • @micheledimaggio8306
    @micheledimaggio8306 6 лет назад +15

    finally he returned!!! relaxing soldering video :)

  • @ovalwingnut
    @ovalwingnut 2 года назад +1

    That process seemed like the "hot tip" and was a visual treat... Thank you.

  • @pwarrow8858
    @pwarrow8858 2 года назад +1

    You are legit the best teacher and the definition of if there is a will there Is a way.

  • @tf3confirmedbuthv54
    @tf3confirmedbuthv54 4 года назад +4

    This channel is by far the best soldering tips and general info about soldering channel i’ve ever found

  • @bearwithme90
    @bearwithme90 6 лет назад +5

    Best soldering techniques channel on RUclips

  • @watchingdanny
    @watchingdanny Год назад +1

    WOW !! Outstanding skill and technique. I'm gonna try these on some scrap computer parts before I feel comfortable but I never even thought it possible. Great video.

  • @robotroom
    @robotroom 5 лет назад +48

    After watching his video, I tried it myself when recapping an old IIci motherboard. It works well. This trick removed 12 corroded capacitors with no lifted pads or burned boards. Just use lots of flux (with an open window/fume extractor) and lots of solder (for thermal mass).

  • @smash7777-
    @smash7777- 6 лет назад +12

    Cool video! The copper wire trick is nice. I have seen it before but never tried it myself. Maybe I will now.
    Thanks for sharing a very cool and interesting video. I’m sure it will help lots of people stuck in a bind.
    👍🏼

    • @user-xl8mi9gf3p
      @user-xl8mi9gf3p 2 года назад

      Да для варианта в полевых условиях самое то используя подручные средства, лучше не придумаешь

  • @Appregator
    @Appregator 5 лет назад +26

    Thanks for the copper wrap around ic pins trick. Great idea

    • @BADALICE
      @BADALICE 4 года назад +1

      Yes. I liked that too.

    • @l0k048
      @l0k048 3 года назад

      i think it's kapton tape

  • @gipielle
    @gipielle 6 лет назад +1

    It's a pleasure to watch your videos!

  • @shambles9
    @shambles9 3 года назад

    Thanks @Andrakavo! tried out some of the techniques you showed here and they work so great!

  • @eduardoavila646
    @eduardoavila646 6 лет назад +255

    The only problem with that techinique is that you heat up too much the components.
    With a really controlled hot air unit you can reduce the stress in the heat-sensitive chips

    • @jay22alco
      @jay22alco 4 года назад +27

      Not really. Depends on how tight the components are in the board and most component can handle that heat otherwise hot air will also damage other component with how they heat up not only the component you want to remove.

    • @buddhistsympathizer1136
      @buddhistsympathizer1136 3 года назад +35

      If the chip is faulty and needs replacing, so what?

    • @ovetomash148
      @ovetomash148 3 года назад +11

      With some old boards u will pick up the the foil...

    • @Atelierul29
      @Atelierul29 3 года назад +9

      @@jay22alco that's why you have various sized tips on your hot air gun....

    • @geraldbal461
      @geraldbal461 3 года назад +2

      true specially if you use cheap irons and it gets dirty easily

  • @noviy_polsovatel
    @noviy_polsovatel 6 лет назад +648

    It's suitable only for dead components

    • @falconeagle3655
      @falconeagle3655 6 лет назад +56

      Thanks. It was so cringe. I would have commented the same.

    • @DestroManiak
      @DestroManiak 5 лет назад +232

      A dead component is one of the biggest reasons you might want to desolder something

    • @TheHamster4430
      @TheHamster4430 5 лет назад +60

      I could disagree with you. All temperature sensible components I've successfully desoldered and then soldered again are still working. I couldn't tell the same about heat gun...

    • @losien1
      @losien1 5 лет назад +68

      Your comment just proved how much you know about soldering... Although I do know both techniques this one is even safer than hot air as the heat is only provided to the soldering points - not to the core of a chip or PCB that acts as a heatsink like it is in the case of using hot air. Both techniques have their advantages and disadvantages but what you've said it totally wrong.

    • @anudeep23222
      @anudeep23222 5 лет назад +1

      This is very costly....not good

  • @shao1423
    @shao1423 3 года назад +10

    The way he uses Iron blows my mind.

  • @clanderson0
    @clanderson0 3 года назад +124

    the flux is strong with this one

    • @jkadofo
      @jkadofo 3 года назад +5

      I can even smell it from here 😁

    • @tnt-hv6qw
      @tnt-hv6qw 3 года назад +1

      😂😂😂😂😂😂😂

    • @wilsonlimeira4252
      @wilsonlimeira4252 2 года назад

      Aonde agente encontra esse material pra comprar

    • @goldnicks
      @goldnicks 2 года назад

      @@wilsonlimeira4252 se chama pasta de solda ou fluxo de solda, geralmente vc encontra para vender em lojas de componentes.

  • @sbellaharris
    @sbellaharris 4 года назад +4

    What I do with QFP's is using the chisel tip to melt the solder and bend one pin up at a time, but remember to press the chip down while you're bending the pins so it doesn't lift any solder pad that's still soldered to other pins.

  • @user-vm1hi7bo5s
    @user-vm1hi7bo5s 3 года назад +25

    3:50 "DIE DIE DIE DIE
    DIE DIE DIE DIE DIE "

    • @aswingsharif6729
      @aswingsharif6729 3 года назад +1

      🤣🤣 LoooL...

    • @overept8801
      @overept8801 3 года назад

      шо этим хотел сказать

    • @user-vm1hi7bo5s
      @user-vm1hi7bo5s 3 года назад

      @@overept8801 А шо нипанятна?

    • @overept8801
      @overept8801 3 года назад

      @@user-vm1hi7bo5s бля я ток до пер на резисторах было написано тип смерть

    • @user-vm1hi7bo5s
      @user-vm1hi7bo5s 3 года назад

      @@overept8801 Ок)

  • @lrg6483
    @lrg6483 3 года назад

    Very Very good desoldering system, the best i have saw in all time!

  • @John_Smith__
    @John_Smith__ 5 лет назад +2

    Truly a good video :) Keep on doing your very good videos!

  • @gamezonealgeria5612
    @gamezonealgeria5612 4 года назад +8

    creative! i really enjoyed watching!

  • @hightttech
    @hightttech 6 лет назад +26

    Very useful. Thank you.

    • @grandmaitregilberto2469
      @grandmaitregilberto2469 5 лет назад +1

      No it is not useful because the components are exposed to heath too much time and are internaly destroyed

  • @46B3x2you
    @46B3x2you 4 года назад

    I wouldn't have thought that adding solder would help to remove it. Very Good.

  • @user-mq9wq3mu8i
    @user-mq9wq3mu8i 2 года назад

    Ничего более завораживающего не видел!!! Просто супер!!! Прям медитация!

  • @bejoterus8715
    @bejoterus8715 6 лет назад +4

    always nice to see such a good soldering trick like this

  • @DMarko22
    @DMarko22 6 лет назад +4

    I had to do something similar last week and failed amazingly...we'll, maybe I'll give it another try.
    PS:There is something pleasant watching your solder jobs.

    • @paulreeder5241
      @paulreeder5241 4 года назад

      Sorry so late but, "Failed amazingly"? Did you mean "Miserably"? lol

    • @DMarko22
      @DMarko22 4 года назад

      @@paulreeder5241 It was amazing how bad I failed that job...that was the intention of the sentence.
      It was indeed a miserable attempt.
      Have a good one mate.

  • @acportrait
    @acportrait 4 года назад +18

    Great video, everything very clean and practical, I loved this technique
    Excelente vídeo, tudo muito limpo e prático, adorei esta tecnica

  • @colorprintvg6936
    @colorprintvg6936 6 лет назад +1

    amzing! thank you for the tips :)

  • @madduxmak5975
    @madduxmak5975 3 года назад +4

    It's great. I've learned a lot of skills here.

  • @galileo_rs
    @galileo_rs 6 лет назад +3

    That flux works pretty nice, surprised to see that it was a "Mechanic" brand. And the chip desoldering was epic :)

    • @Pixell_Eletronica
      @Pixell_Eletronica 3 года назад

      what is the brand of the flux?

    • @galileo_rs
      @galileo_rs 3 года назад +1

      @@Pixell_Eletronica Mechanic, obviously. Watch the video until the end, all the tools are listed.

  • @sergiogreiso6221
    @sergiogreiso6221 3 года назад

    Great video, everything very clean and practical, I loved this technique !!! It's WORK !

  • @MakeFirePro
    @MakeFirePro 5 лет назад

    Good video you have. I would like to see the restoration of tracks after erosion under the chip

  • @sridharanpvl
    @sridharanpvl 4 года назад +4

    Those components agreed to come out of the board. Impressive.

    • @jkadofo
      @jkadofo 3 года назад

      😂😂👍

  • @ElTexMexAlex
    @ElTexMexAlex 5 лет назад +3

    Good video, I was looking for this.

    • @yudycheng6576
      @yudycheng6576 3 года назад

      PCB and FPC supplier Mr.Cheng TEL(Wechat) : (86)18166347566 yudypcb@gmail.com

  • @piyushkadukar7337
    @piyushkadukar7337 5 лет назад

    Good Work Buddy. I appreciate your work.

  • @KahaKhotiem
    @KahaKhotiem 3 года назад

    A kind of great soldering art!

  • @demionlindsayable
    @demionlindsayable 6 лет назад +19

    this man is a genius!

  • @mohsentech4292
    @mohsentech4292 6 лет назад +5

    +Androkavo Professor :)
    I love your welding techniques very much and recommend for you the following tips:
    T15-BCM2
    T15-BC28

  • @Daniel_Wolf
    @Daniel_Wolf 4 года назад +1

    Master!...great demonstration. clap clap clap!!!

  • @imanwiharjo9486
    @imanwiharjo9486 2 года назад

    wow .. didnt know if these were even possible. hats-off!

  • @jazzmcc4223
    @jazzmcc4223 4 года назад +65

    This is so satisfying to watch

  • @y_x2
    @y_x2 4 года назад +6

    For small components use two soldering gun. For dead parts use an exacto and cut all the pins.

  • @TheSalatech
    @TheSalatech 4 года назад

    Nice video... now i finally know, what the knife tip is good for :)

  • @мр.Олександр
    @мр.Олександр 4 года назад +1

    Thanks a lot for this video!) It's awesome!

  • @yuanho2883
    @yuanho2883 6 лет назад +15

    You are a master on the art

  • @Ridata01
    @Ridata01 6 лет назад +3

    i envy so much your soldering skills

  • @alexanderm.9566
    @alexanderm.9566 3 года назад +2

    The increasing difficulty levels, accompanied by great musics. I want to play this video game!

  • @whyrate
    @whyrate 4 года назад +1

    I love the Adams Family style music too! Nice video

  • @mikea3169
    @mikea3169 4 года назад +4

    Nice video; brings me back to when I was an assembly and rework tech. We had a hot air station but during rework I usually opted for a wide chisel tip or a hoof tip on the Metcal. So quick and easy. Only used the hot air for QFN packages and things of that sort.

  • @marcelomigueldasilva7444
    @marcelomigueldasilva7444 2 года назад +5

    A qualidade da solda ajuda muito e com essa técnica melhor ainda. Obrigado!

  • @HelpingMind
    @HelpingMind 5 лет назад

    I enjoy your work.

  • @christiankulmann3325
    @christiankulmann3325 4 года назад

    Sehr gut und hilfreich. Thank you.

  • @user-vd5iu6ku6y
    @user-vd5iu6ku6y 4 года назад +18

    All of that looks really impressive (like Chinese magic ;-)), but a bit tricky for a beginner...;-)
    And there's still a big risk to damage the components while trying to remove them like this.
    BTW, you can also use Rose alloy instead of ordinary solder to reduce the operating temperature (it's quite a common approach).

  • @abuzain2797
    @abuzain2797 6 лет назад +21

    PRO....The Real Master Soldrr

  • @sainttwo88
    @sainttwo88 3 года назад +2

    ваши ролики как произведения искуства)))красиво методично интересно . спасибо 😀

  • @leso204
    @leso204 Год назад

    I have heard of this method but first time to see it done , good backup tool .......

  • @mikegaming4924
    @mikegaming4924 3 года назад +10

    You are essentially heating the IC to the Solder melting point, then it transfers heat to the legs and to the pad too. That DPAK appears to be little bit difficult to remove with soldering iron.

    • @lepidoptera9337
      @lepidoptera9337 2 года назад

      You cut the two two or three leads off, then you can easily remove the package.

  • @axelbelleris
    @axelbelleris 6 лет назад +3

    Éso fue hermoso. 💖 Lo voy a practicar. ¡Gracias!

    • @elcomentador2408
      @elcomentador2408 6 лет назад +2

      Like por hablar español jajaja xD

    • @axelbelleris
      @axelbelleris 6 лет назад

      @@elcomentador2408 ¡Jaja! Saludos desde Córdoba, Argentina. 😎

  • @MrPolluxxxx
    @MrPolluxxxx 2 года назад

    The wire trick is pretty neat.

  • @victorpiedra6742
    @victorpiedra6742 3 года назад

    Awesome tips for smd components desoldering, if it's broken or burned, doesn't really matter if you apply some overheating, trying to re-use components it's a different story, I will put in practice those skills in the video

  • @ut4321
    @ut4321 3 года назад +5

    We're not worthy, we're not worthy! Amazing skills.

  • @Skidtire
    @Skidtire 6 лет назад +4

    Can you make a video comparing acid free plumbing flux to electronics flux?

  • @RSTVlog87
    @RSTVlog87 3 года назад

    Thanks for the copper trick, very useful :)

  • @Rotoham
    @Rotoham 4 года назад

    Great work!

  • @MyJuankmilo
    @MyJuankmilo 4 года назад +5

    For this I just use thin braided copper wire with flux and when heated with a soldering iron, the copper absorbs all the tin in the circuit freeing the components

    • @dalethomasdewitt
      @dalethomasdewitt 4 года назад

      Wicks are pedantic. A big blob till tweezer-time is faster. Every method has merit. Know your limit.

  • @persona83
    @persona83 4 года назад +3

    Ok, the componets may already be damaged, so no need to worry about excessive heat. But what about the copper trails?

  • @Ammy-bc6bh
    @Ammy-bc6bh 5 лет назад

    Thanks for such a nice technique

  • @MelkiSilvas
    @MelkiSilvas 6 лет назад

    Nice video!!! Nice job! 😀

  • @nikiamz6501
    @nikiamz6501 6 лет назад +7

    5:00 really creative method

  • @ninjaslash52_98
    @ninjaslash52_98 3 года назад +55

    I’m assuming the parts you removed are unusable afterwards
    Also god damn that’s a nice flux

    • @delayed_control
      @delayed_control 3 года назад +6

      If they're already broken and need replacement I guess it's fine anyway.

  • @bmwmpower1491
    @bmwmpower1491 3 года назад

    Good Job, great work!

  • @naderhumood1199
    @naderhumood1199 5 лет назад

    Thanks man exellant job I love it so much your perfect 👍

  • @himeccms893
    @himeccms893 6 лет назад +4

    Great idea, very helpful video! Presumably the soldering iron temperature need to be lower or else the PCB copper will detach from board? Also the components can't be reused anymore due to prolong exposure to such high temperature?

    • @mattquick5045
      @mattquick5045 5 лет назад +2

      Still a newbie so don't know about the temp. But this is desoldering not recovering components. So yes most components will be dead after this treatment.

  • @mscpro
    @mscpro 3 года назад +4

    Wow ...this is a great skill, an experienced man in soldering. We are a beginner must learn longer to have a skill like this. It's a great job showed us. But by the way... may i know..what flux and tin kind you applied there ?!

  • @Entertainmentandmuchmore6088
    @Entertainmentandmuchmore6088 2 года назад

    copper wire technique is too good,
    You are perfect person in this work, great work ,congratulations Dear🍫👏🏻💐
    When I was in service department ..... I also love my job,
    After watching your vdo I want to do this again🙌🏻

  • @swlee9289
    @swlee9289 5 лет назад

    awesome technique. thanks for sharing.

  • @HermanOtto-wr2nn
    @HermanOtto-wr2nn 6 лет назад +7

    Bardzo pomysłowy sposób bez przegrzewania bocznych układów łapka w górę

  • @Cameron-qn3wz
    @Cameron-qn3wz 4 года назад +112

    Overheating, destroy others parts.

    • @aswingsharif6729
      @aswingsharif6729 3 года назад +24

      This should be aimed to replace the desoldered part, not to fix the pin connection from bad soldering, so yes, next step is to replace the part.

    • @SwanandsCreativity
      @SwanandsCreativity 3 года назад +2

      Yes

    • @heyjohnsmith
      @heyjohnsmith 3 года назад +2

      @@aswingsharif6729 This makes sense, tq

    • @heyjohnsmith
      @heyjohnsmith 3 года назад +6

      @Soren Kylo @Maxwell fuck you scammers, who are also spreading unhealthy insecurities

    • @alexipetrovski7868
      @alexipetrovski7868 2 года назад +1

      Even with a hot air technique, what happened to the caution we were told to have when soldering so as not to overheat delicate chips?
      Removing parts is one thing as they're going in the bin but got to solder the new part back on. These things are done with pin point accuracy by machines in factories for a reason.

  • @fb4709
    @fb4709 Год назад

    This is the most satisfying video ever...

  • @cameronrich2536
    @cameronrich2536 10 месяцев назад

    So helpful. Wish I could like this twice

  • @AliYassinToma
    @AliYassinToma 6 лет назад +3

    I used to do this but i use a regular wire not a single core one i wrap it around the soldering tip then around the chip i turn on the soldering iron and remove the chip

    • @Wilson84KS
      @Wilson84KS 6 лет назад +2

      Me too, I'm using all that methods, but wrapping some wire around the tip of soldering iron and bend it into right shape is better that a U-formed piece which is only touched by the tip, you need ways less solder and it goes faster, the parts don't need to be heated up that much. To be honest we both kind of copy this idea from special iron tips, didn't we? 😂

  • @shafiqalom8408
    @shafiqalom8408 4 года назад +39

    By this process, any component easily can be destroyed and loss it's property...

    • @jeremyvi
      @jeremyvi 3 года назад +1

      I dont thinknso: Wave soldering which is very popular in board factories is the same process for building board.

    • @ro63rto
      @ro63rto 3 года назад +2

      If a component is being removed, more often than not it has failed so what's the issue??

    • @ayuchanayuko
      @ayuchanayuko 3 года назад +2

      @@ro63rto or you are removing it from a donor board

  • @felipinho14d65
    @felipinho14d65 4 года назад

    Very satisfying video!

  • @san_x2576
    @san_x2576 4 года назад +1

    Out of series my friend you are an animal ... great !!!

  • @TM-kt2lh
    @TM-kt2lh 5 лет назад +5

    Superman 🤣😎👍 Тосно like ставить нужно....!!!

  • @dofrint2027
    @dofrint2027 4 года назад +9

    That's a high quality flux

  • @RaffizeeAchoi
    @RaffizeeAchoi 3 года назад

    So nice... thanks for your sharing sir🤩👍🏻

  • @MrAjmal2010
    @MrAjmal2010 5 лет назад +2

    He is just outstanding.. 😍

  • @kbjinsam
    @kbjinsam 4 года назад +6

    Androkavo, your video is very clear! What microscope did you use?

  • @ftcgaming4651
    @ftcgaming4651 4 года назад +6

    To anyone who's worried that this might damage components, I've done this multiple times on SPI ROM chips to dump them and never have I had any of them fail. Only real issue is the board that might burn a bit.

    • @crf80fdarkdays
      @crf80fdarkdays 2 года назад

      Nek minnit...

    • @M-H433
      @M-H433 11 месяцев назад

      Was just wondering about the heat

  • @shoaibiqbal7172
    @shoaibiqbal7172 5 лет назад

    Very good work friend i like it very much.

  • @surinderdhiman
    @surinderdhiman 4 года назад

    Very useful video. Thanks a lot and Hats off

  • @rickpontificates3406
    @rickpontificates3406 3 года назад +5

    Putting a solid wire around a component, even that SOIC-24, isn’t necessary to remove it with a soldering iron.

  • @recogehmar1848
    @recogehmar1848 6 лет назад +12

    Thanks for this! Are the components re-usable afterwards?

    • @nelsonlobo3615
      @nelsonlobo3615 3 года назад

      Fried

    • @eugenegrebionkin
      @eugenegrebionkin 3 года назад +1

      I think they are reusable. When desoldering using air, you also apply heat to whole component and not only its legs. So I think the temperature on the component is not so far from air desoldering

    • @neilkurzman4907
      @neilkurzman4907 3 года назад

      The resistors are probably reusable.
      With active components you run the risk of heat damage. But sometimes They work

    • @eugenegrebionkin
      @eugenegrebionkin 3 года назад +1

      @@neilkurzman4907 well if we actually check the internals of ICs, we'll see that there are very thin wire going between the chip leg and the actual crystal. I don't think much heat can be transferred through it. So as for me, heating the IC's case is way more dangerous than heating its legs

    • @neilkurzman4907
      @neilkurzman4907 3 года назад

      @@eugenegrebionkin
      The plastic also doesn’t accept heat very well. You can guess, but the question is is it worth reusing a potentially damaged component.

  • @saifuladliyusof334
    @saifuladliyusof334 3 года назад

    Thanks for this tutorial! ❤❤

  • @isaiasmartinez3508
    @isaiasmartinez3508 3 года назад +1

    Excelente información
    Muchas gracias maestro