Below for reference, correct me if I am wrong: Cameras Supported for Digital Focus Control The following cameras can be paired with the gimbal over Wi-Fi for direct digital focus control from the gimbal when using select lenses Canon: 80D, 6D Mark II, 6D, 200D, 5D Mark IV Panasonic: GH4, DMC-LX100, DMC-LX10, DC-ZS70GK, DC-ZS220GK, DC-GF9XGK, DC-GF9KGK, DC-GH5SGK-K, DC-GX9KGK-K, DC-GF10KGK Cameras Supported for Digital Zoom Control The following cameras can be paired with the gimbal over Wi-Fi for direct digital zoom in/out control from the gimbal when using select lenses Sony: a7 III, a7S II, a7R, RX100 V, RX100 IV, RX100 VI, a5100, a6000, a6500, a6300, QX1 Panasonic: DMC-LX100, DMC-LX10, DC-ZS70GK, DC-ZS220GK, DC-GF9XGK
@@khooRicky Canon 6D should able to start recording video and either wifi or control cable can do that. video recording via cable control may set your camera shutter to control video recording
@@ianhavingfun Not sure why my copy having problems with cable connection. And another problem is keep vibrate when using auto adapat in Payload Setting. Both update and balancing had been done.
@@khooRicky Sorry, just saw this question, have you tried to set the Payload setting 11:08, because auto adapat will need gimbal to detect the camera weight, so it will be vibrating at the very beginning, it is suggest to set the Payload setting of your camera and lens
@@juanelcolombiano123 Yes, my gimbal came with a follow focus kit. I mounted that on, but not using it adding a little weight to the lense to balance it.
Hi Todovid, may I know if you have the Feiyu Ak2000? because these two accessories should come with Feiyu AK4000, and if you would like to get them separately for your AK2000, you can contact Feiyutech to get them, their email should be： service@feiyu-tech.com
I just received mine today. When I go to the payload screen I do not get choices of weight ranges. I get preset, auto and custom but cannot figure out how to put a custom number in. Do you know? Thanks
Hf-r and TF-r mode not showing I confirm firmware is up to date. And I followed the instructions by single click on power button when in HF mode, still not showing Any suggestions
I got the Gimbal today but i cannot balance the pan axis with my Sony A7Riii and the Sony 24-105 f4.0 and as well with the sigma MC11 and canon 50mm 1.8. It just wont balance it. The tilt axis is no problem and when starting the Gimbal it works too, but if i try to hold the gimbal vertical, it just starts going crazy... any thoughts on this ? Tried it too with my GoPro and Note 9, same Problem....
@@ianhavingfun Just uploaded a Video to my Account. As you can see, everything works but the Pan Axis makes Problems. It's in all Lock Mode. And this is not the A7Riii with the 24-105 but this should work to with a Canon 50D.
Hello, I didn't see a reference to Nikon in the video. Can you please direct me where can I get an explanation of how to connect my Nikon D750 to Gimbal?
@@ianhavingfun Thanks , I was a little screwed up because I didn't believed Nikon are not taken into account. any way, I saw in one of the places a recommendation to purchase a cable that connects between the camera USB and the gimbal, do you think it would allow control anything from the gimbal control panel? And thanks again for your patience
@@meiraviyam5461 Yes, Nikon would have two shutter type, DC2, and DC0, depends on camera model, and gimbal part would need a 3.5mm jack, connected by the shutter cable, ak2000/ ak4000 can control your camera Shutter.
@@ianhavingfun I tried all sony interface and the gimbal I don't know but the buttons each time I change mode just start moving on its on, thanks for the replay
@@ianhavingfun in my opinion it's good if you can do it all without cables. because on the Sony camera when using a cable it will deactivate OSS / ibis
@@Mus_Jepretz I agree so, but also would note that Feiyu or Zhiyun is the three-part company to Sony Fuji or Canon, Nikon; and All Brand cameras would have their own Camera protocol so three-part company would need to have cooperation with Camera company to open their access to WIFI or wireless function, so it will still need a long way to go.
@@Giannis_Manousos Nikon would have DC0 and DC2 two kind of shutter type, and the Feiyu Ak gimbal connector port is 3.5mm. I enclosed you product link on Amazon for your reference: www.amazon.com/dp/B07GWPDVNL
Sure, just set the auto-rotation, and put your camera on the recording. you may not connect the gimbal and your camera, so just press the video recording button on your camera
Using a6000 and selp18105g I did not get a noticable response to zoom or focus control. That being said I have a similar situation with playmemories so probably not a global issue. The A6000 can't charge while shooting and you can't start and stop video this is a limitation of the a6000. The a6300 and a6500 should support all these functions.
@@williamoneill5777 William. Sony A6000 Zoon function should work if you have already connected to the gimbal via Feiyu On app. And electronic focus control is not applied to Sony Camera, as far as I know, may need Servo Follow Focus to do manual control. start and stop video not applied to a6300, that is true.
@@ianhavingfun Thanks for the heads up. I'll have another go with getting zoom to work. I was so happy with all the other good stuff on the AK2000 I didn't investigate the zoom control properly. When I ordered my AK2000 I ordered the follow focus kit from a China supplier so it will be weeks before that arrives :(.
so, i just got my ak4000 and there appears to be a lack of functionality for the rear button like in moza air 2 or ronin s as holding it down does not change behavior. But what i find more frustrating is there is no way that i found to rotate on the roll axis only and lock all other axis. All other major gimbals have this option to just be able to use the joystick to rotate the camera 360 degrees (inception mode on moza for example) as well as the speed is very slow and could not find a way to set speed or deadband, the app seems lacking in those areas where customizing the sensitivity and control of the movement is key. I am planning on doing a video review so if there is a way id like to know. Thanks!
I have some issues for the battery cover. Can't close it properly while the batteries are loaded. It works fine when you put the outer cover. I liked the Gimbal very much. Does anyone face the same issue? Please comment!
Hi, Nikon camera would need to buy a follow servo focus( Feiyu AF I/ AF II), check below link if you would like to have a close look: ruclips.net/video/H_C5vaccRAk/видео.html Direct digital focus control from the gimbal when using select lenses Canon: 80D, 6D Mark II, 6D, 200D, 5D Mark IV Panasonic: GH4, DMC-LX100, DMC-LX10, DC-ZS70GK, DC-ZS220GK, DC-GF9XGK, DC-GF9KGK, DC-GH5SGK-K, DC-GX9KGK-K, DC-GF10KGK
When I turn on my AK 2000 the touch screen does not work, it brights white, but doesn't react to anything. It makes the noise when you turn it on, I can use the joystick and the recording button, I can also connect it to the app. Any tips?
@@gergelypatanyi4911 There will be two issue will case touchscreen just show brights white, and not data: 1. Gimbal Firmware or keypad board Firmware does not work correctly. Just update them via PC/ Mobile Feiyu on App will work, (I suggest do it via PC) 2. the Data cable on the gimbal mainboard has been lost or short circuit Needs to be sent back to repair store, or return it back to your seller
No More Rat Race& Tizzy Tokyo, if you would ask about if the gimbal can be balanced and work with Nikon D750, the answer is positive, and you can get a Nikon control cable to connect the gimbal so gimbal can control your camera shutter; But the WIFI connect would not apply to Nikon D750
I want to use the AK2000 ( preferably because is lighter than the 4000) with my sony FDR-AX700 Camcorder- but i'ts impossible to get a reply from the manufacturer for any compatibility. Could you tell me what is the distance in mm between the front of the roll motor (facing the camera LCD/ virwfinder) and the center of the tilt motor / shaft of the motor- so I could measure if my camcorder battery and viewfinder would hit the roll motor...I have spent days calling all local camera shops but no one has a disolay unit..Thanks
Yeap, Feiyu ak2000 can support nikonD5200, but you would need to get the Nikon Shutter cable separately, or gimbal would not able to control your camera shutter.
Where did you get the long 1/4 thumb screw for the quick release plate? The package only includes the short thumb screw that is too short to attach camera to the thick side of quicrelease plate
@@ianhavingfun The short one was in the package, but not the long one used to attach the camera to the quickrelease plate. The one thats at 1:24 in your video
@@vandenmichael1057 If gimbal has small vibration, please adjust the motor dynamics setting via Feiyu on App or gimbal screen as needed, Set about to Level 2 or Level 3
@@vandenmichael1057 Canon 600d is not supported to adjusted parameter from gimbal yet. and vibrate may caused by incorrect payload setting or heavy lens without lens frame support. here is a video in details. check it out: ruclips.net/video/HV4SHFH4wzc/видео.html
AK2000 With GH5 many problems. Appear noise all time with panaleica 12-60 . Remote connector dont have space to put. Wifi appear for panasonic image app not for Feiyu app... In app dont appear gh5 model ( appear gh4 and gh5 S)
Got an AK2000 for my Sony a6000 and Sigma 30mm f1.4... I think it's impossible to balance the gimbal on pan axis. There is just no more space to move the arm backwards. When you switch on the gimbal it seems to work ok, but then I checked the footage, OMG. It's all jittery and has so much vibrations. Maybe somebody has any idea or there are some kind of adapters to balance the setup? It seems that the vibration and the jittery video is from the unbalanced pan axis...
Hi, sorry that I don't have the Sigma lens, so not able to test it. could you make a short video to show the problem? Also, I enclosed Feiyu After service Email: service@feiyu-tech.com
Well, I think i figured out how this can be fixed. You have to apply some additional weight to the right side of the mounting plate. It seems that when a6000 is mounted on the gimbal it has just weird center of gravity and because of that it's impossible to balance the pan. Used some duct tape and weights from the steadycam... Looks weird but it works now. Hopefully there will be some kind of adapter to put on top of the mounting plate, so that the camera would be placed more to the right side...
Sorry that not app can check it, but you can check it easily, video (at 3:10) has shown the balanced gimbal-camera can stay at any angle. You may need a few hours to learn how to balance it, after that, you may make it done within 3 mins. Practice makes perfect.
Hi Canon M50 is on compatible list, and it can control taking pictures/video by WiFi and Bluetooth system. Check you AK2000 and Feiyu On Play, make sure they are both the newest version. By the way, what smartphone are you using, please?
@@ianhavingfun it is on the list but i just couldn't connect them. it will stay connected for 3 seconds then disconnect the camera to gimbal. i'm using iphone and i've checked all of the firmware are up to date
@@ianhavingfun figured it out. on the M50, it's usually paired to my iPhone. so when i change it to connect to a computer and making the camera as an excess point, it works.
Bonjour . Dans les réglages quelle est le différence entre LK-LKR, - HF et HFR ;Donc ma question est la suivante ,a quoi sert le R . J ai demandé en France mais personne ne répond Merci
Bonjour. R = suivre le roulement ( R= Rolling follow) HF-RPanning = Mode + suivi de roulement (HF-RPanning=Mode + Rolling follow ) TF-R = Mode de verrouillage + suivi de roulement (TF-R=Lock Mode + Rolling follow LK-R = Follow Mode + Rolling Follow (LK-R=Follow Mode + Rolling follow) Désolé pour mon google français.
Excusez moi de vous déranger de nouveau mais je ne vois pas la différence avec ou sans le R . Je suis vraiment novice dans ce domaine et avec un age assez avancé , Bientôt 70 ans .Un grand MERCI
hey, in my payload settings I dont have options i "grams" like you, I have only position "level 1, level 2, level 3, level 4, level 5, Custom 1, Custom 2, Custom 3... do you know how to change it? Its reason why I dont know which one option is the best for my camera (a6300 with sigma 1.4 30mm ).
Hi Folek90, Below data for your reference: Level 1: 0-500g Level 2: 500-1000g Level 3: 1000-1500g Level 4: 1500-2000g Level 5: 2000g above You can adjust it accordingly.
Question on auto rotation: I have a Canon M50. Whenever I set up auto rotation, it sometimes automatically triggers the shutter to take a still. This creates a problem when trying to set it for video as it creates an error in the camera causing it to freeze up. I then have to remove the battery to reset it. I essentially cannot shoot video with auto rotation. I do not know why the gimbal triggers the shutter button when it is set to video. I have DWELL and Interval on zero, and some parameters for pan and tilt for the shot I want. Have you tried this gimbal with a Canon and have you experienced this issue, or do you know of a setting that I might be doing wrong that will correct this? Thanks!!
Auto Rotation will e for mobile time lapse Photography, so it may trigger shutter in your set time because time-lapse was made by pictures I think you can just set the Rotation position and disconnect your camera WIFI, so gimbal will not able to control your gimbal shutter
Hi Maro, you can get a Nikon Control cable if you just have a Nikon camera, with the shutter cable , Nikon camera can do Time-lapse photography as well
Below for reference, correct me if I am wrong:
Cameras Supported for Digital Focus Control
The following cameras can be paired with the gimbal over Wi-Fi for direct digital focus control from the gimbal when using select lenses
Canon: 80D, 6D Mark II, 6D, 200D, 5D Mark IV
Panasonic: GH4, DMC-LX100, DMC-LX10, DC-ZS70GK, DC-ZS220GK, DC-GF9XGK, DC-GF9KGK, DC-GH5SGK-K, DC-GX9KGK-K, DC-GF10KGK
Cameras Supported for Digital Zoom Control
The following cameras can be paired with the gimbal over Wi-Fi for direct digital zoom in/out control from the gimbal when using select lenses
Sony: a7 III, a7S II, a7R, RX100 V, RX100 IV, RX100 VI, a5100, a6000, a6500, a6300, QX1
Panasonic: DMC-LX100, DMC-LX10, DC-ZS70GK, DC-ZS220GK, DC-GF9XGK
Canon 6D can't record video when WIFI is on. The follow focus can work with cable ? or must use wireless connection?
@@khooRicky Canon 6D should able to start recording video and either wifi or control cable can do that.
video recording via cable control may set your camera shutter to control video recording
@@ianhavingfun Not sure why my copy having problems with cable connection. And another problem is keep vibrate when using auto adapat in Payload Setting. Both update and balancing had been done.
@@khooRicky Sorry, just saw this question, have you tried to set the Payload setting 11:08, because auto adapat will need gimbal to detect the camera weight, so it will be vibrating at the very beginning, it is suggest to set the Payload setting of your camera and lens
Have Fujifilm insulted all gimbal manufacturers?
I can't seem to get 3:08 to balance with a6300 kit lens 18-55mm just ran out of space on the bar.
Lucky Luke me too bro! Did you ever fixed it?
@@juanelcolombiano123 Yes, my gimbal came with a follow focus kit. I mounted that on, but not using it adding a little weight to the lense to balance it.
Juan Alvarez did you fix it too?)
FeiyuTech AK2000/AK4000 are really good for DSLR camera, thanks!
My ak2000 is permanently on LK settings..please how do I fix it
What is the defrent between ak2000 and ak4000 .. pleas tell me ..
Mine, the roll axis always go back to horizontal position. Any sugestions?
Gosh, you make this all look so simple! It's not. Remotely.
Nice video, where i can buy accesories on 4:03 hotshoe adapter and vertical rod?
Hi Todovid, may I know if you have the Feiyu Ak2000? because these two accessories should come with Feiyu AK4000, and if you would like to get them separately for your AK2000, you can contact Feiyutech to get them, their email should be： service@feiyu-tech.com
@@ianhavingfun i have AK 2000
I just received mine today. When I go to the payload screen I do not get choices of weight ranges. I get preset, auto and custom but cannot figure out how to put a custom number in. Do you know? Thanks
How can i fast the speed of the gimbal
Hf-r and TF-r mode not showing
I confirm firmware is up to date. And I followed the instructions by single click on power button when in HF mode, still not showing
Any suggestions
I have the same problem. Before firmware update, i had these 2 options, after update, it is not working. If i knew it, i wouldn't update it anymore :(
Will this work with the canon rebel t6s?
will this work with the canon eos M50,,gud teacher
Yes, sure, but I recommed to check the Feiyu AK2000S, as this ak2000 is an old model now
can you make a video of connected the app to sony.,.the record button not working for me
Hi Shaji, recording control not apply to Sony a6000 and sony Connection start at 6:30, in this video.
Does is work with a canon Eos 4000d??
Hello, after turning to selfie mode can't go back normal .
Hi Ian, Can to do a video to show how to do 360 camera rotation using AK2000 or tell me the steps on how to do ?.
It is simple- enter the AF mode, and then use the Joystick to make a 360 roll.
@@ianhavingfun Thanks. Will try
@@ianhavingfun , Actually I want to know how to do the vertical 360 camera rotation ?
is it avaivable with canon 77d? I can't use the focus mode! thanks
Can you use Wifi connection to operate gimbal, let say on cable cam? Or Wifi is just for video preview? Thank you
Wifi connection can apply for camera parameters adjust and shutter control, but depends on the camera model, check the description
Does it support 5dmark111?
I got the Gimbal today but i cannot balance the pan axis with my Sony A7Riii and the Sony 24-105 f4.0 and as well with the sigma MC11 and canon 50mm 1.8. It just wont balance it. The tilt axis is no problem and when starting the Gimbal it works too, but if i try to hold the gimbal vertical, it just starts going crazy... any thoughts on this ? Tried it too with my GoPro and Note 9, same Problem....
Sony A7Riii with Sony 24-105 should able to balance the pan axis, have you made a short video?
@@ianhavingfun Yeah I know that it should work, but it doesn't. No I haven't.
@@machmutdoener Could you make a short video and sent it to ian2010071139@gmail.com? I will check if I can help, or can forward it to Feiyu IT team
@@ianhavingfun Sure, but it will take a couple of days, because I just got my teeth out..
@@ianhavingfun Just uploaded a Video to my Account. As you can see, everything works but the Pan Axis makes Problems. It's in all Lock Mode. And this is not the A7Riii with the 24-105 but this should work to with a Canon 50D.
Thank you so much! This was so helpful!
Nice Video, can help us new buyers too much.
Hello,
I didn't see a reference to Nikon in the video. Can you please direct me where can I get an explanation of how to connect my Nikon D750 to Gimbal?
Hi Meir, Nikon Cameras are not able to connected by Wifi
@@ianhavingfun Thanks
, I was a little screwed up because I didn't believed Nikon are not taken into account. any way,
I saw in one of the places a recommendation to purchase a cable that connects between the camera USB and the gimbal, do you think it would allow control anything from the gimbal control panel?
And thanks again for your patience
@@meiraviyam5461 Yes, Nikon would have two shutter type, DC2, and DC0, depends on camera model, and gimbal part would need a 3.5mm jack, connected by the shutter cable, ak2000/ ak4000 can control your camera Shutter.
@@ianhavingfun Thanks
buttons for hard reset? ?
Hi. nice guide video... ak2000 vs ak4000 differences only in payload ???
Yeap, AK2000 will be enough for DSLR camera
Any way to make it work the app with the Sony A6400 ?
Hi Ivan, what is the problem you meet with Sony A6400? you would try to connect by a6300 interface, or wait for the App update.
@@ianhavingfun I tried all sony interface and the gimbal I don't know but the buttons each time I change mode just start moving on its on, thanks for the replay
I have a Sony 6300 camera with a power zoom lens, can I adjust the zoom, record button and other parameters without cables?
Yes, you can do so.
But you would need to get the gimbal WIFI and your Camera WIFi connected. it would be done in Feiyu On app.
@@ianhavingfun
in my opinion it's good if you can do it all without cables.
because on the Sony camera when using a cable it will deactivate OSS / ibis
@@Mus_Jepretz I agree so, but also would note that Feiyu or Zhiyun is the three-part company to Sony Fuji or Canon, Nikon;
and All Brand cameras would have their own Camera protocol so three-part company would need to have cooperation with Camera company to open their access to WIFI or wireless function, so it will still need a long way to go.
Is there a way to connect a nikon camera? I have a d5300. Thanks.
Yes, you can have a Nikon control cable with 3.5mm jack, then your gimbal would able to control you camera shutter.
www.amazon.com/dp/B07GWHHBY5 For your check.
There is no camera cable control for NIKON. WHY?
need to purchase seperately
@@ianhavingfun there is no cable to buy
@@Giannis_Manousos Nikon would have DC0 and DC2 two kind of shutter type, and the Feiyu Ak gimbal connector port is 3.5mm. I enclosed you product link on Amazon for your reference: www.amazon.com/dp/B07GWPDVNL
After I move my gimbal it slowly drifts to the right when I'm not touching it. How can I stop this?
Rich, try to tighten the all Screws, and balance the gimbal.
Can the auto-rotation feature be used for video? If so, how?
Sure, just set the auto-rotation, and put your camera on the recording. you may not connect the gimbal and your camera, so just press the video recording button on your camera
does this gimbal break in half when storing?
The gimbal handle can be separated.
Can this work with sony a6000 for follow focus and zooming?
Zoom function will work, follow focus may need Servo Follow Focus to achieve that
Using a6000 and selp18105g I did not get a noticable response to zoom or focus control. That being said I have a similar situation with playmemories so probably not a global issue. The A6000 can't charge while shooting and you can't start and stop video this is a limitation of the a6000. The a6300 and a6500 should support all these functions.
@@williamoneill5777 William. Sony A6000 Zoon function should work if you have already connected to the gimbal via Feiyu On app.
And electronic focus control is not applied to Sony Camera, as far as I know, may need Servo Follow Focus to do manual control.
start and stop video not applied to a6300, that is true.
Here is the Follow Focus Tool:
www.feiyu-tech.com/akf2
@@ianhavingfun Thanks for the heads up. I'll have another go with getting zoom to work. I was so happy with all the other good stuff on the AK2000 I didn't investigate the zoom control properly. When I ordered my AK2000 I ordered the follow focus kit from a China supplier so it will be weeks before that arrives :(.
so, i just got my ak4000 and there appears to be a lack of functionality for the rear button like in moza air 2 or ronin s as holding it down does not change behavior. But what i find more frustrating is there is no way that i found to rotate on the roll axis only and lock all other axis. All other major gimbals have this option to just be able to use the joystick to rotate the camera 360 degrees (inception mode on moza for example) as well as the speed is very slow and could not find a way to set speed or deadband, the app seems lacking in those areas where customizing the sensitivity and control of the movement is key. I am planning on doing a video review so if there is a way id like to know. Thanks!
Is the integrated follow focus only working with wifi connection or can I use the shutter cable to control it? (Canon 77D)
Could get an extra to follow focus servo to control Zoom lens.
I have some issues for the battery cover. Can't close it properly while the batteries are loaded. It works fine when you put the outer cover. I liked the Gimbal very much. Does anyone face the same issue? Please comment!
don't have this issue, may be you would need to change the cover.
do you have to be connected to a phone to have the wheel be in manual focus mode? (I have a nikon so it appears i cant connect to my phone)
Hi, Nikon camera would need to buy a follow servo focus( Feiyu AF I/ AF II), check below link if you would like to have a close look:
ruclips.net/video/H_C5vaccRAk/видео.html
Direct digital focus control from the gimbal when using select lenses
Canon: 80D, 6D Mark II, 6D, 200D, 5D Mark IV
Panasonic: GH4, DMC-LX100, DMC-LX10, DC-ZS70GK, DC-ZS220GK, DC-GF9XGK, DC-GF9KGK, DC-GH5SGK-K, DC-GX9KGK-K, DC-GF10KGK
that AK2000, is it compatible with X-T20?
camera control may not be available, but the basic stable function will work fine!
When I turn on my AK 2000 the touch screen does not work, it brights white, but doesn't react to anything.
It makes the noise when you turn it on, I can use the joystick and the recording button, I can also connect it to the app. Any tips?
so it can be turned on, but the Touch Screen not able to show anything? have you try to update gimbal firmware?
Ian Z Yes, I have done that.
@@gergelypatanyi4911 There will be two issue will case touchscreen just show brights white, and not data:
1. Gimbal Firmware or keypad board Firmware does not work correctly.
Just update them via PC/ Mobile Feiyu on App will work, (I suggest do it via PC)
2. the Data cable on the gimbal mainboard has been lost or short circuit
Needs to be sent back to repair store, or return it back to your seller
Ian Z Thank you! I will try it!
Hi, will this work with the Fuji xt3?
Payload will be just fine, AK2000, Payload: 250g/0.55lb --- 2800g/6.17lb. but there will not shutter cable for Fuji xt3, and will no App support also.
what does it mean Digital Focus Control ?
No need to add follow focus servo; can achieve Focus Follow Control
Is the Nikon D750 fully supported?
Imma wait for the answer to this too
No More Rat Race& Tizzy Tokyo, if you would ask about if the gimbal can be balanced and work with Nikon D750, the answer is positive, and you can get a Nikon control cable to connect the gimbal so gimbal can control your camera shutter;
But the WIFI connect would not apply to Nikon D750
Very helpful, thanks for your video.
I want to use the AK2000 ( preferably because is lighter than the 4000) with my sony FDR-AX700 Camcorder- but i'ts impossible to get a reply from the manufacturer for any compatibility. Could you tell me what is the distance in mm between the front of the roll motor (facing the camera LCD/ virwfinder) and the center of the tilt motor / shaft of the motor- so I could measure if my camcorder battery and viewfinder would hit the roll motor...I have spent days calling all local camera shops but no one has a disolay unit..Thanks
sony FDR-AX700 Camcorder would be too long for Feiyu Ak2000.....
So this isn't for Nikon users at all?
Hi, Nikon Camera would not able to connect via wifi, but with cable connection, it would able to control camera Shutter.
This is insanely good.
Yeap, it is the newest gimbal that made by Feiyu
Hey Feiyutech ak2000 can work with nikonD5200?
Yeap, Feiyu ak2000 can support nikonD5200, but you would need to get the Nikon Shutter cable separately, or gimbal would not able to control your camera shutter.
@@ianhavingfun which one is better MC-DC2 N3 or MC-DC2?
Nice product, nice video :-) Do you know where to find the Follow Focus accessory ?
Feiyu official web or Amazon will sell those accessories, but highly recommend to get a Kit with accessories
Where do I plug in my A7 (Mark 1)?
Do you mean the control cable? there should be a Sony cable.
@@ianhavingfun Found it. Thanks :)
can sony a6300 connect with feiyu ak2000?
Sure, Sony a6300 with 28-70 lens and 16-50 lens has been tested. it will work fine with AK2000
I had to modify my gimbal to use it with a6300+35/1.8 otherwise it would balance the pan axis
This product looks well-made with so many accessories, how much is it?
it depends, in the USA, AK2000=379$, and AK4000=599$
Where did you get the long 1/4 thumb screw for the quick release plate? The package only includes the short thumb screw that is too short to attach camera to the thick side of quicrelease plate
Sorry that I can't get your question, did your package miss the lone one? There is a short one for the len support frame.
@@ianhavingfun The short one was in the package, but not the long one used to attach the camera to the quickrelease plate.
The one thats at 1:24 in your video
@@siimernits3581 Contact your seller to get a replacement screw...
Hello, in my ak2000 when I raise the power of the engines make noise. It is normal? Good video
May I know the gimbal is perfectly balanced?
With a Heavy lens, don't forget to mount the lens support frame.
@@ianhavingfun Exactly, it was because I did not use the lens holder, when I put it on, it does not sound strange anymore. Thank you
@@cuenk8487 Glad to hear that!
How u make it spin
Check the video from 9:00- 12:54 about main interface, including all kind of models, you would find out.
How can I change the language for your device?
Get an international version, when you start the gimbal for the first time, it will have a langue option.
@@ianhavingfun I dont saw any language option. Last menus appear in chinesse characters. App need a better version
@@alexlapuerta4735 Please check " 系统设置“ means " System" , and click" 系统设置“ , Then you can find "语言选择“ means "language“
Find them on the LED screen.
@@ianhavingfun thanks for this I was a little lost this solved it
Feiyu AK2000 can work with Canon 600d?
Yeap, for balancing? sure! but gimbal control camera may not able to be achieved. you may need a shutter cable so gimbal can control camera shutter
Last week i bought this gimbal. Its cool. Can work with Canon 600d. But not for controlling the parameter. Sometimes the gimbal vibrate. Why?
@@vandenmichael1057 If gimbal has small vibration, please adjust the motor dynamics setting via Feiyu on App or gimbal screen as needed, Set about to Level 2 or Level 3
@@vandenmichael1057 Canon 600d is not supported to adjusted parameter from gimbal yet. and vibrate may caused by incorrect payload setting or heavy lens without lens frame support. here is a video in details. check it out:
ruclips.net/video/HV4SHFH4wzc/видео.html
AK2000 With GH5 many problems. Appear noise all time with panaleica 12-60 . Remote connector dont have space to put. Wifi appear for panasonic image app not for Feiyu app... In app dont appear gh5 model ( appear gh4 and gh5 S)
I think buy ak2000 for gh5 and bmpcc4k but i think this no good for it...
how you think gh5 will be add to app?
Hi
Alex, I suggest contacting Feiyu IT department directly to get support
service@feiyu-tech.com
@@Lookmyfly As far as I know, USA Amazon market and B&H still no Feiyu Ak series inventory on sale, so Feiyu may know the problem and trying to fix it
Ian Z i get information ak2000 support gh5 too
@@Lookmyfly Nice to hear that and thank you to let me know.
Got an AK2000 for my Sony a6000 and Sigma 30mm f1.4... I think it's impossible to balance the gimbal on pan axis. There is just no more space to move the arm backwards. When you switch on the gimbal it seems to work ok, but then I checked the footage, OMG. It's all jittery and has so much vibrations. Maybe somebody has any idea or there are some kind of adapters to balance the setup? It seems that the vibration and the jittery video is from the unbalanced pan axis...
Hi, sorry that I don't have the Sigma lens, so not able to test it. could you make a short video to show the problem?
Also, I enclosed Feiyu After service Email: service@feiyu-tech.com
Same issue, but mine is kit lens 1650sel
Well, I think i figured out how this can be fixed. You have to apply some additional weight to the right side of the mounting plate. It seems that when a6000 is mounted on the gimbal it has just weird center of gravity and because of that it's impossible to balance the pan. Used some duct tape and weights from the steadycam... Looks weird but it works now. Hopefully there will be some kind of adapter to put on top of the mounting plate, so that the camera would be placed more to the right side...
@@unltDe wow that's a gd. Thanks so much. Totally agree with ur idea.
@@unltDe BTW how much weight u have put in order to balance the weight for pan axis with ur sigma lens.
THANK YOU!
Hi Ian,
is there any option on Feiyu mobile app to check whether the AK2000 gimbal is successfully balanced or not ?
Sorry that not app can check it, but you can check it easily, video (at 3:10) has shown the balanced gimbal-camera can stay at any angle.
You may need a few hours to learn how to balance it, after that, you may make it done within 3 mins. Practice makes perfect.
can't seem to connect the Canon M50 to the gimbal at all
Hi Canon M50 is on compatible list, and it can control taking pictures/video by WiFi and Bluetooth system.
Check you AK2000 and Feiyu On Play, make sure they are both the newest version.
By the way, what smartphone are you using, please?
@@ianhavingfun it is on the list but i just couldn't connect them. it will stay connected for 3 seconds then disconnect the camera to gimbal. i'm using iphone and i've checked all of the firmware are up to date
@@maxhoh If keep disconnecting, it may also be the Bluethooth chip get lose or disfuntion, contact your seller to return for a replacement
@@ianhavingfun figured it out. on the M50, it's usually paired to my iPhone. so when i change it to connect to a computer and making the camera as an excess point, it works.
@@maxhoh Thank you for sharing!
can support for 5DM2?
Feiyu AK2000 would be enough for Canon 5DM2
How much does the Feiyu AK2000 weigh?
Hi, Offical data is 1252g, and payload: 250g/0.55lb--2800g/6.17lb
Ian Z thank you. Definitely picking this up.
Bonjour . Dans les réglages quelle est le différence entre LK-LKR, - HF et HFR ;Donc ma question est la suivante ,a quoi sert le R . J ai demandé en France mais personne ne répond Merci
Bonjour.
R = suivre le roulement
( R= Rolling follow)
HF-RPanning = Mode + suivi de roulement
(HF-RPanning=Mode + Rolling follow
)
TF-R = Mode de verrouillage + suivi de roulement
(TF-R=Lock Mode + Rolling follow
LK-R = Follow Mode + Rolling Follow (LK-R=Follow Mode + Rolling follow)
Désolé pour mon google français.
@@ianhavingfun Merci
Excusez moi de vous déranger de nouveau mais je ne vois pas la différence avec ou sans le R . Je suis vraiment novice dans ce domaine et avec un age assez avancé , Bientôt 70 ans .Un grand MERCI
My tail cap is stuck!!! No idea how to fix this
Put some Oil?
Use a screwdriver or other tools to knock the tail cap lightly while rotating the handle. That might be helpful.
I had to use pliers. It scratched the paint off but it worked lel
Cool video man! :) Does it work with Sony A7II? Follow focus work with this basic package or some adds are neccesery? Thank you
Hi Michal, as far as I know, All Sony A7/ a6 series camera would need to add accessories to achieve Follow focus.
Is it comparable with the Canon EOS 5Dsr
hey, in my payload settings I dont have options i "grams" like you, I have only position "level 1, level 2, level 3, level 4, level 5, Custom 1, Custom 2, Custom 3... do you know how to change it? Its reason why I dont know which one option is the best for my camera (a6300 with sigma 1.4 30mm ).
Hi Folek90, Below data for your reference:
Level 1: 0-500g
Level 2: 500-1000g
Level 3: 1000-1500g
Level 4: 1500-2000g
Level 5: 2000g above
You can adjust it accordingly.
Question on auto rotation: I have a Canon M50. Whenever I set up auto rotation, it sometimes automatically triggers the shutter to take a still. This creates a problem when trying to set it for video as it creates an error in the camera causing it to freeze up. I then have to remove the battery to reset it. I essentially cannot shoot video with auto rotation. I do not know why the gimbal triggers the shutter button when it is set to video. I have DWELL and Interval on zero, and some parameters for pan and tilt for the shot I want. Have you tried this gimbal with a Canon and have you experienced this issue, or do you know of a setting that I might be doing wrong that will correct this? Thanks!!
Auto Rotation will e for mobile time lapse Photography, so it may trigger shutter in your set time because time-lapse was made by pictures
I think you can just set the Rotation position and disconnect your camera WIFI, so gimbal will not able to control your gimbal shutter
@@ianhavingfun Great idea. Thanks for the help!
@@firpofutbol Cheer! and Share your video if you would make one.
SUPER !!!
So i cant use the follow focus with the a6500?
Yeap, you would need to buy a follow servo focus, if you would like to do follow focus
This helps alot, thanks. I'm going to get this one tomorrow.
Hope that you can update for nikon control :)
Hi Maro, you can get a Nikon Control cable if you just have a Nikon camera, with the shutter cable , Nikon camera can do Time-lapse photography as well
thanku so much ...
The world needs a smart gimbal to auto balance ... hahaaa...
Also, auto detects what camera it mounts and connect gimbal and camera automatically...En...
Hope it comes out soon.
🎬 1 📽 🎞 🗣 🎙 🤔 🧐 ❤️❤️❤️❤️❤️ Outstanding, thank you so much for sharing. 🌎🌍🌏 You are a Good teacher ✅✅✅✅✅
Where the AK2000?????
All the functions of AK2000 and Ak4000 are the same, so...
I didnt know it can spin
That repetetive music is so anoying :(