This video is the solution for fixing the ERR20 problem, also for the EOS200D. Just remove the front, back and top cover (disconnect the flat cables), removing any PCB is not necessary. A sprocket is visible through the small gap where the shutter motor is located beside the flashlight. Rotate the small sprocket with a small screwdriver. Rotate until the mirror is in the upper positon. Close the cases (don't forget to connect the flat cables) and insert the battery. The mirror is repositioned and the camera is working again.
I just got the Err20 error, so I took off the lens, lifted up the mirror, and one of the blades of the shutter had a small tear in it. It caused one blade to overlap the other, and I gently pushed it back in place and now it's working! It may pop back out again, but for now I'm glad it works!
@@jazminjaz1256 The problem with your shutter might be a little different, but this is what worked for me. To see the shutter, I took off the lens, and then with a popcicle stick or something, I lifted up the trap-door mirror to show the shutter behind it. (Be careful! You are VERY close to the sensor and if you mess it up you break your whole camera!) See if any of the blades of the shutter are out of place or overlapping. It should look like horizontal lines all the way down. On mine, one flap of the shutter was overlapping another. With the precision of a surgeon, I set it back in place and now it works! Hope that helps!
Wow, I'm shocked I was able to fix my Eos M using this method. I took the camera apart until I found a spinny gear thing. Spun it to close the shutter, wiggled it a bit and now it works. I was pretty hasty about removing screws. lol It may never be put together 100% but it takes photos again non-the-less!
Hi Everyone! Before you go thorough all this taking your lovely Canon body into a zillion pieces try the following, because it could work as well and can save you a lot of extra work. When you open the battery compartment on your camera you can feel with your fingers that the battery can slightly move inside, because of that spring that pushes it back from the bottom. I think this error comes up when the contact is not sufficient with the battery, so try the following: - open the battery compartment door - put a fully charged battery in - get a piece of paper and fold it until it becomes 1-2 millimeters thick - put the paper on top of the battery - now it will be a bit harder to close the battery door but try. If it is too hard, do not force it, just tear a small part of the paper off so it gets a little thinner (but make sure the paper will for sure apply a bit of extra push-in pressure on the battery.) and then you can close the door. - now try to shoot... For me it worked just fine, I hope it will work for you as well...
Just an update on this topic. In the meantime, I asked an official Canon repair service here about this error. They said this caused by the malfunction of the shutter. They can replace it for about $750. My camera works just fine ever since I did this hack and I have not seen this error at all. Did I save a $750 repair? It seems like...
new suscriber from chile ! dude thank you soo muchhhhhh i was in such a hurry, we're leaving town in SF, ca. and the camera took a fall and it'll be so necessary the next days, almost pay a $180 for a 4 days repeair, i couldnt wait, instead i bought some screwdrivers and now it works again ! blesses
This video helped me immensely. I was actually getting a 99 error but I realized the shutter was stuck and when I turned the gear it was working again. Thank you so much man.
Unfortunately didn't work for me, seemed like it was going to and then after a pic went back to doing the same thing. I can now remove the battery and have it give me the ability to scroll through the pics which I couldnt, etc. But as soon as I go to shoot, err 20 again. Thanks anyways.
Thank you, my 80D had this error and i was scared the shutter was ok but the mirror was locked and it happened when i. Was filming, i watched this video and just forced a little bit the mirror to come down, just a little, like if i was trying to pull it down but not too much, than i closed the camera and re-install the batteries and the mirror came down and it ia ok now
I need a small set of screwdrivers to fix my facebook market place robbery lol. Used one time by her son in taking camera class and poof she blocked me when I messaged her about the err 20 on a Canon T6 which will display the menus but no video mode. It will occasionally sound like it wants to take a pic in other modes but same err 20 comes up and only the view finder no display. I did get it to display pics on a used SD but nothing else. Tried the paper to hold the battery in and the shutter looks okay.
I have Nikon 5600 today I found a problem on my camera that is .....when I click a photo on my cam the picture was so oily patches on dslr screen but when I download the same photo to my laptop the picture was alright ... kindly suggest me the solution
Had this issue a few times, sent it in twice to be fixed. Just had it again when I set my camera to "silent shooting mode" So I think certain lenses do not support silent shooting mode. This is worth a shot if anyone has the issue.
Hello bhaijaan mai nepal se hun mera pass yek dslr camera hai usme video shoot hota hai lekin ....o video adobe premier me video add karne ke time o video mp3 show karne lagta hai ...to bhai aap ko pata hai to please batayega thanks bhai jannn
Looking at all these stupid and annoying errors I think we would be better off with a box camera. And to think we all can spend thousands of pounds for this --- disgracefull !!!
Wish Indians would stop putting horrible music on good videos. Pretty much good video, thanks for your time, but please do, stop putting horrible music on videos.
@@oakland10e3 I guess he is Asian, probably he meant "You just opened it and CORRECTED it...."Asians do misspronuounce r and l since it has no difference in sound for them!
![Kodak Black - Catch Fire [Official Music Video]](http://i.ytimg.com/vi/A4ch-olIuZo/mqdefault.jpg)
This video is the solution for fixing the ERR20 problem, also for the EOS200D. Just remove the front, back and top cover (disconnect the flat cables), removing any PCB is not necessary. A sprocket is visible through the small gap where the shutter motor is located beside the flashlight. Rotate the small sprocket with a small screwdriver. Rotate until the mirror is in the upper positon. Close the cases (don't forget to connect the flat cables) and insert the battery. The mirror is repositioned and the camera is working again.
I just got the Err20 error, so I took off the lens, lifted up the mirror, and one of the blades of the shutter had a small tear in it. It caused one blade to overlap the other, and I gently pushed it back in place and now it's working! It may pop back out again, but for now I'm glad it works!
How can u explain plz
@@jazminjaz1256 The problem with your shutter might be a little different, but this is what worked for me. To see the shutter, I took off the lens, and then with a popcicle stick or something, I lifted up the trap-door mirror to show the shutter behind it. (Be careful! You are VERY close to the sensor and if you mess it up you break your whole camera!) See if any of the blades of the shutter are out of place or overlapping. It should look like horizontal lines all the way down. On mine, one flap of the shutter was overlapping another. With the precision of a surgeon, I set it back in place and now it works! Hope that helps!
Wow, I'm shocked I was able to fix my Eos M using this method. I took the camera apart until I found a spinny gear thing. Spun it to close the shutter, wiggled it a bit and now it works. I was pretty hasty about removing screws. lol It may never be put together 100% but it takes photos again non-the-less!
Hi Everyone! Before you go thorough all this taking your lovely Canon body into a zillion pieces try the following, because it could work as well and can save you a lot of extra work. When you open the battery compartment on your camera you can feel with your fingers that the battery can slightly move inside, because of that spring that pushes it back from the bottom. I think this error comes up when the contact is not sufficient with the battery, so try the following:
- open the battery compartment door
- put a fully charged battery in
- get a piece of paper and fold it until it becomes 1-2 millimeters thick
- put the paper on top of the battery
- now it will be a bit harder to close the battery door but try. If it is too hard, do not force it, just tear a small part of the paper off so it gets a little thinner (but make sure the paper will for sure apply a bit of extra push-in pressure on the battery.) and then you can close the door.
- now try to shoot...
For me it worked just fine, I hope it will work for you as well...
This worked for me! Thank you!
thanks
Just an update on this topic. In the meantime, I asked an official Canon repair service here about this error. They said this caused by the malfunction of the shutter. They can replace it for about $750.
My camera works just fine ever since I did this hack and I have not seen this error at all. Did I save a $750 repair? It seems like...
OH MY GOODNESS YOU JUST SAVED ME SO MUCH MONEY!! THANK YOU!
Thank you so much, I really appreciate it dude!
new suscriber from chile ! dude thank you soo muchhhhhh i was in such a hurry, we're leaving town in SF, ca. and the camera took a fall and it'll be so necessary the next days, almost pay a $180 for a 4 days repeair, i couldnt wait, instead i bought some screwdrivers and now it works again ! blesses
Holy cow! Whatever he's doing, this is not an easy fix 😆!
Sound track helps in no way explanation would be much more helpful
This video helped me immensely. I was actually getting a 99 error but I realized the shutter was stuck and when I turned the gear it was working again. Thank you so much man.
Fantastic video! I was freaking out when I saw that error message. My mirror was stuck up. I fixed it and so far so good.
I was lucky enough to have it work with the first check!
This is extremely hard to follow when u aren’t explaining anything (in caption or verbally)
Unfortunately didn't work for me, seemed like it was going to and then after a pic went back to doing the same thing. I can now remove the battery and have it give me the ability to scroll through the pics which I couldnt, etc. But as soon as I go to shoot, err 20 again. Thanks anyways.
Thank you my friend its working you help me
Thank you, my 80D had this error and i was scared the shutter was ok but the mirror was locked and it happened when i. Was filming, i watched this video and just forced a little bit the mirror to come down, just a little, like if i was trying to pull it down but not too much, than i closed the camera and re-install the batteries and the mirror came down and it ia ok now
I need a small set of screwdrivers to fix my facebook market place robbery lol. Used one time by her son in taking camera class and poof she blocked me when I messaged her about the err 20 on a Canon T6 which will display the menus but no video mode. It will occasionally sound like it wants to take a pic in other modes but same err 20 comes up and only the view finder no display. I did get it to display pics on a used SD but nothing else. Tried the paper to hold the battery in and the shutter looks okay.
Not all pieces need to be opened.Solved in5 minuter.The gear wheel is reached if you just unscrew the screen down.
Can you explain more how you just get to the gear?
Yesss explain please
I have Nikon 5600 today I found a problem on my camera that is .....when I click a photo on my cam the picture was so oily patches on dslr screen but when I download the same photo to my laptop the picture was alright ... kindly suggest me the solution
Had this issue a few times, sent it in twice to be fixed. Just had it again when I set my camera to "silent shooting mode" So I think certain lenses do not support silent shooting mode. This is worth a shot if anyone has the issue.
This problem total cost?
I used a pencil eraser on both ends where the battery connection meets the camera connection and I’m up and shooting again.
Canon 7d apa bisa diperbaiki dengan cara seperti itu
Hello bhaijaan mai nepal se hun mera pass yek dslr camera hai usme video shoot hota hai lekin ....o video adobe premier me video add karne ke time o video mp3 show karne lagta hai ...to bhai aap ko pata hai to please batayega thanks bhai jannn
2x shutter blade canon 700d Price
Vi ata mekar k dele koto tk lagbe thik korte plz bolen vi err 20 koto tk lagbe plz bolen plz
It works! Thank you!
yess luckly it was only the shutter mechanism !
thanks alot
I fixed the problem in 1 minute. I can't belive
Can you give the solution
thank you
Where can I get a new shutter mechanism so that I can repair it. Camera’s shutter is toast.
thanks
Looking at all these stupid and annoying errors I think we would be better off with a box camera. And to think we all can spend
thousands of pounds for this --- disgracefull !!!
thanks !
thanks
Hello sir my camera is not opening infact battery is fully charged but then also it is not opening plz solve the problem sir
*Sir care Mei le Jane Se Kitna cost aayega* ❓
सर कितना खर्चा आता है
यदि आप स्वयं सर्विसिंग कर सकते हैं, तो यह मुफ़्त है।
सर आपका नंबर दे सखते है क्या
Wish Indians would stop putting horrible music on good videos.
Pretty much good video, thanks for your time, but please do, stop putting horrible music on videos.
Thanks
Good
thanks
Sir what is the cost to fix it
Over $300
Bhai err 99 deka ra h or batrry nikalni ke bad on hota h fir ik pic py fir problem yr plz btao na
Bhai mera camera error 20 bata raha hai bataiye kase sahi hoga kya problem hai
Amar camera suddenly display light hocche na ki krbo kindly ekto help krben amake ki krbo bolben dada
Thanks bai. This helped me.
Goof bye my camera for ever i thing
Bye 700d 😶🤥🤣🤣
Thanks
thanks man you save me
You just opened it and collected it and that’s it?
"collected it" -- what the heck does that mean???!!!!
@@oakland10e3 I guess he is Asian, probably he meant "You just opened it and CORRECTED it...."Asians do misspronuounce r and l since it has no difference in sound for them!
@@oakland10e3 I guess he meant "dismantled" and "re-assembled" it maybe...
@@AlexSilva-xh2yi When they speak lol, not when they type
I did all this and now my camera won’t start
😄
Did you put the battery back in?
Awesome
the prob is not the camera or the sensor is smt eles
Err 99 solution pls
How can i solved err 50 problem?
how about error 50?
очень не аккуратная работа. грубое снятие ccd (юстировка как ?)
Apner nambr ta den
Vai থেকে সহজ সমাধান নাই।।। নিজে করার মত।।।???
Vai apnar number lagbe. Amro camera tar ei problem.
ঠিক করছেন ভাই
Bhai apke dhokan kaha h
Ek help chye
Err 99 slution plzz
Easy tarika nhi h kya binod
Err 70 solution please
80
Vai apnar Facebook link ta den
Sall debn ata
vai apnar phone number ta den plz amr cemera somporke akto kotha bolbo
This problem total cost?
I'm facing this issue canon 1200d