Prossibly a nice addition to the top of the tool box would be a multimeter or a multimeter current clamp, I got a very good and compact UT210E myself and been using it for years now, no complaints and it has worked reliably for myself. An amazing bit of kit you got there good sir.
Wow, I couldn't believe what I was seeing. I have done a similar thing to my festool boxes. I also split a 3 drawer systainer into a 2 drawer systainer. I remember, I had to make 6 metal wedges and push each wedge into the 6 locations in the drawer frame, then give it a good pull to separate the drawer frames. I thought I was the only person who knew how to split the systainer drawers. In my festool systainer, I have also put small tables on the sides. They are very useful for putting tools on so you don't have to bend all the time. My side table surfaces dismantle and go inside the tool box though to allow for transportation. I can try to get a video on RUclips sometime if you are interested to see it. Keep up the good work!
Hello Max. I set up a RUclips channel to show you some quick movies of my Festool toolboxes. They are not as nice as yours though. This link should work... www.youtube.com/@johnshaw1883/videos
Im not even a tool guy, or a sub but came to check this out from your driveway video discussing this toolbox. Fantastic organization, intensely German. Consider me a tool guy, and a sub!
well thought through box. Designing and printing these are so satisfying if it all falls in place . I recognise a lot of the tools in my box too. Weicon no 5 missing! (I was sceptical, plastic tool, can't be good, but it's the quickest and most efficient tool when stripping loads of wires).. I am not a fan of the Wera allen keys with the large bulky plastic on it. everybody seems to be using them, but I personally favour their stainless set. Also a fan of that 35Nm 12V bosch driver.
3:08 the orange caps i know for sure are not for electrical cables. They are for phone / alarm cable that have a low voltage and carry a low current. I know this for a fact because i worked with it and i an a full licensed electrician too ... Since you said they are for " garden electric stuf and water tight" yea they are water tight but again you cant have anything bigger then a cat 5 cable as an example .. but even for that they are bad because they would cut those cabels right out .. ( since they are single core often) Just sort of feel need to warn people so they dont start using them for any 230 volt stuff ... the blue cap once i cant comment on, dont remember using them ever
I would find room for a 12v Milwaukee bandsaw or jigsaw, a caulking gun, pry bar, level you could hang those from the table on the side. A plumb bob, 4'" vise, some sandpaper electrical duct and painters tape, super glue with accelerator, heat shrink, headlamp, small coil of dyneema line and you should be able to handle most things that can be finished or repaired in a day.
Super cooles Konzept Max! Bin echt begeistert und du hast sehr schöne / gute Werkzeuge. Ich würde den Platz mit einem 1.Hilfe Set füllen, dass wird schnell vergessen, aber macht in einem Werkzeugkasten total Sinn. VG
Max, can you provide more information about the quick releases, the little snap and the cupholder? where did you buy them and or with what name can they be found with google? Nice cart By the way
Hey, my amazon store is in Germany, but the cupholder is easy to find I guess. Those quick releases can be found if you type in Camera quick release or camera snap mount.
Buy one every six months. I am a multi trade and I have to say, they are the best thing on the market. I don't regret a single one I have bought or the wheels etc.
There are way better boxes to buy- Toughsystem2 or Packout for example. Watch where he opens the drawers- sticky... Others have quality metal roller slides. Much stronger construction, too.
Hi Max, what about PPE, or personal protective equipment, not sure if I saw that, but if you added, I missed and apologize. If you don't please think about adding it for your safety when working and making. 🤓That's you with safety glasses on, LOL.
Ja das war echt schwierig. Man kann die einzelnen Lagen von Innen aus einander hebeln. Da sind Wiederhaken die man lösen muss. 3 Stück auf jeder Seite. Wenn man die gelöst bekommt gehen die auseinander und man kann sie beliebig neu zusammen stecken.
@@MaxMakerChannel thanks for the feedback. I was afraid of that. Everyone is using the pack out and I wanted to be different. I work turn arounds at power plants and refineries and need something rugged.
"Blue Wheels" are not too bad for this, as being used for flight cases to transport event equipment. They're a reasonable compromise between tiny wheels and those balloony big tires as in a wheel barrow. Diameter is 100mm /ca. 4 in. and they are firm enough to not wobble too much and soft enough to give in a bit. Either way the problem one might run into is tipping hazard. The higher off the ground the cart goes the more likely it will tip bcs of the small footprint. Loading it top heavy makes it worse. Plz rmember a Festool Systainer box is only 40 x 30 cm in footprint (15.75 x 12 in.)
Awesome. I recommend to add a Tajima Scraper. Love it and use it all the time. As many others I just found your channel through your latest and probably first viral video. Crazy how viral it went. The content is pretty cool though. Do you think the comment from stuff made here boosted the virality a lot?
Awesome setup I have a few questions I am hoping you can answer! What festool systainer are you using on top with the open tool storage? What are the tool dividers in the video for your pliers and screwdrivers? What is the attachment for your Bosch drill driver that allows it to hang off the systainer? Thanks great ideas 👍 💡.
I think he mentioned the inserts in the tool caddy were 3d printed. The open top tool box with the handle is listed as a "tool box" on festools website.
Woher hast du die Einsätze/ Halterung her für dein Werkzeug, was du in der kiste verklebt hast? Aus einem 3D Drucker? Würd mich über ne kurze Rückmeldung freuen!
Hey, yeah it is a camera light for filming. There are a lot of chinese models out there. I connected it with a camera accessory gimble. So 100% camera equipment.
Hallo Max wirklich cooler werkzeugwagen. Hast du mal überlegt wie bei Alexander Chappel 3d gedruckte Container zu machen? wenn es ok ist wollte ich auch fragen was du studiert/ als Ausbildung gemacht hast. bin fast mit der Schule fertig und suche gerade Inspiration. Hello Max really cool toolcar. Have you seen the organizer boxes of Alexander Chappel? I think they could be a useful addition to your shop. If it's ok I wanted to ask what job you studied for? I'm almost finished with school and was interested. I am still in the searching phase and looking for ideas and inspiration.
Hey, diese Container sind ganz cool, aber wir haben davon jede Menge ähnliche Sortimentkisten von Auer-Packaging.com. Die haben 70 cent bis 4€ gekostet und waren am Ende deutlich günstiger und wir mussten nicht tagelang den 3D Drucker blockieren. Ich habe Produktentwicklungsingenieur in England studiert. Das war genau das richtige für mich, aber ich glaube Programieren hätte mir auch gut gefallen. Hauptsache du machst etwas was du interessant findest. Gerade Handwerker sind gefragt wie nie. Ob Klinatechniker oder Dachdecker. Viel Erfolg!
Hallo Max Maker Sie sind Deutscher und sprechen in Ihrem Video nur Englisch. Warum? Ich bin mir jetzt nicht sicher. Ist Ihr Video ein Englisch Sprach Kurs Video? Oder soll Ihr Video ein selbst mach Video sein? Sie würden mir eine Freude machen wenn Sie Ihr Video Kunstwerk noch mal in Ihrer Muttersprache Deutsch machen könnten. Mfg ✌️
![DIY Systainer Roll Board [video 451]](http://i.ytimg.com/vi/bu7CKKugP8g/mqdefault.jpg)
![DIY Systainer Roll Board [video 451]](/img/tr.png)
nice tool cart!
Nothing, NOTHING is better than a well planned customized toolbox. LOVE it!
Prossibly a nice addition to the top of the tool box would be a multimeter or a multimeter current clamp, I got a very good and compact UT210E myself and been using it for years now, no complaints and it has worked reliably for myself. An amazing bit of kit you got there good sir.
Wow, I couldn't believe what I was seeing. I have done a similar thing to my festool boxes. I also split a 3 drawer systainer into a 2 drawer systainer. I remember, I had to make 6 metal wedges and push each wedge into the 6 locations in the drawer frame, then give it a good pull to separate the drawer frames. I thought I was the only person who knew how to split the systainer drawers. In my festool systainer, I have also put small tables on the sides. They are very useful for putting tools on so you don't have to bend all the time. My side table surfaces dismantle and go inside the tool box though to allow for transportation. I can try to get a video on RUclips sometime if you are interested to see it. Keep up the good work!
I would love to see that. Maybe you are my lost twin!
Ok, I will try and arrange a video soon
@johnshaw1883 nice!
Hello Max. I set up a RUclips channel to show you some quick movies of my Festool toolboxes. They are not as nice as yours though. This link should work... www.youtube.com/@johnshaw1883/videos
@@MaxMakerChannel Hello, I have put the video on RUclips now.
I love the way you have attached things (the square) to the SYS-TOTE 🙂
Very cool. Could you share some plans for the 3d printed Inlays?
im specifically looking for the wera alan key holder, thats just so good!
That looks Great Max, I can see a lot of thought went in to this build 🛠👍😊
Looking good. Everything in its place.
Thanks for sharing your mods, Max.
Im not even a tool guy, or a sub but came to check this out from your driveway video discussing this toolbox. Fantastic organization, intensely German. Consider me a tool guy, and a sub!
well thought through box. Designing and printing these are so satisfying if it all falls in place . I recognise a lot of the tools in my box too. Weicon no 5 missing! (I was sceptical, plastic tool, can't be good, but it's the quickest and most efficient tool when stripping loads of wires).. I am not a fan of the Wera allen keys with the large bulky plastic on it. everybody seems to be using them, but I personally favour their stainless set. Also a fan of that 35Nm 12V bosch driver.
That’s well thought out, wow!
3:08 the orange caps i know for sure are not for electrical cables. They are for phone / alarm cable that have a low voltage and carry a low current. I know this for a fact because i worked with it and i an a full licensed electrician too ... Since you said they are for " garden electric stuf and water tight" yea they are water tight but again you cant have anything bigger then a cat 5 cable as an example .. but even for that they are bad because they would cut those cabels right out .. ( since they are single core often)
Just sort of feel need to warn people so they dont start using them for any 230 volt stuff ... the blue cap once i cant comment on, dont remember using them ever
Extraordinary tool kit!Well thought out and executed Sir!
Thank you! It is indeed super helpfull.
Great job! That's such a great idea. Especially the cup holder! 🤩Stay hydrated guys 👌
I would find room for a 12v Milwaukee bandsaw or jigsaw, a caulking gun, pry bar, level you could hang those from the table on the side. A plumb bob, 4'" vise, some sandpaper electrical duct and painters tape, super glue with accelerator, heat shrink, headlamp, small coil of dyneema line and you should be able to handle most things that can be finished or repaired in a day.
Love the collection and the tools you make
Sweet kit! Did I miss it or do you perhaps need a few loose sheets of a few grits of sandpaper? Maybe add a some abrasives and light solvents.
The sandpaper is a good idea. Ill add it to the list! The Isopropyl is good for all kinds of glue and grease.
Super cooles Konzept Max! Bin echt begeistert und du hast sehr schöne / gute Werkzeuge. Ich würde den Platz mit einem 1.Hilfe Set füllen, dass wird schnell vergessen, aber macht in einem Werkzeugkasten total Sinn. VG
Only just found your channel and I'm loving the content ! Much respect from Scotland
Thanks for watching! Greatings from Germany : )
hi, i would put some Knipex 180mm pliers in the toolbox an i would change the Bosch 12v Driver to the Flexiklick driver
Very nice build!! Please be so kind and list the sustainer formats of it so we can build the same!🙏
Great design
Absolutely brilliant
You should add a first aid kit to this :) never know when there's an acident!
Gut gelöst.
Very cool, lot of good ideas in there.
great do more 3d Accesories for the festool .Forsintant longer items. and can you share you designs so we can print them too thanks
I learned so much, thank you for sharing great ideas!!! 😊👍
Awsome, Thanks Max 😊
That's really cool. I like that.
i suggest bolting on a churro maker on the side for fuel
Nice work on this
Könntest du die Dateien von den Werkzeughalten vielleicht zur Verfügung stellen? Das wär super :)
Very nice!
Can you please post the stls and f3d files for the organizers so others can print and modify them? I am not sure if you use thingiverse or printables.
I wish I could purchase the table sides. Great work!
Max, can you provide more information about the quick releases, the little snap and the cupholder? where did you buy them and or with what name can they be found with google? Nice cart By the way
Hey, my amazon store is in Germany, but the cupholder is easy to find I guess. Those quick releases can be found if you type in Camera quick release or camera snap mount.
Very cool
Die Behäler sind stabil, ich hätte jedoch sicherheitshalber Unterlagsscheiben bei den Blindnieten und Blindnietmuttern hinzugefügt.
This is the most German thing I’ve ever seen 🙈🤣 And that’s a compliment. Very impressed!
hey cool video. Festool looks good quality. I like the whole 3d print design.
Макс классно 👍🏼
Hi awesome video, what is the height of the drawers?
I don’t know exactly. About 6-7cm.
@@MaxMakerChannel thanks! :)
Very nice set up. I'm inspired to finally update my home based tool cart. Now to find a weekend to implement!
I don't use even a quarter of the tools in there, but I want this!
Maybe a place for the kitchen sink…seems to be the only item you forgot. Just kidding, very nice setup. Hils fra Danmark 🇩🇰
I got excited and checked what these Festool boxes cost to buy and now I can't stop crying 🥺.
I never considered buying them until I got two boxes for my birthday. But the quality is very convincing.
Buy one every six months.
I am a multi trade and I have to say, they are the best thing on the market.
I don't regret a single one I have bought or the wheels etc.
There are way better boxes to buy- Toughsystem2 or Packout for example. Watch where he opens the drawers- sticky... Others have quality metal roller slides. Much stronger construction, too.
Not going to lie I'm jelly
Sehr geiles Setup.. gibt mir evtl ein paar Inspirationen :)
Hi Max, what about PPE, or personal protective equipment, not sure if I saw that, but if you added, I missed and apologize. If you don't please think about adding it for your safety when working and making. 🤓That's you with safety glasses on, LOL.
Hey yeah we got it! Earplugs, headphones, safety glasses and gloves.
Mega Turm!! Welche Lampe ist das genau? Und welcher Halter?
Die Lampe ist eine 0815 Videolampe. Der Halter kommt aus dem Fotobereich. Das sind so Schnellverschlüsse.
This is beautiful.
Sehr nice. Kannst du mir vielleicht genauer verraten wie du den Sortainer abgeändert hast?
Ja das war echt schwierig. Man kann die einzelnen Lagen von Innen aus einander hebeln. Da sind Wiederhaken die man lösen muss. 3 Stück auf jeder Seite. Wenn man die gelöst bekommt gehen die auseinander und man kann sie beliebig neu zusammen stecken.
Красавчик! Отлично организовано!
What did you use to cut the aluminum @3:54?
How is it rolling across rocks or gravel?
Bad
@@MaxMakerChannel thanks for the feedback. I was afraid of that. Everyone is using the pack out and I wanted to be different. I work turn arounds at power plants and refineries and need something rugged.
If I needed bigger wheels I would just strap the whole thing to a cart for crates. Like the one movers use. With 300mm wheels.
"Blue Wheels" are not too bad for this, as being used for flight cases to transport event equipment. They're a reasonable compromise between tiny wheels and those balloony big tires as in a wheel barrow. Diameter is 100mm /ca. 4 in. and they are firm enough to not wobble too much and soft enough to give in a bit.
Either way the problem one might run into is tipping hazard. The higher off the ground the cart goes the more likely it will tip bcs of the small footprint. Loading it top heavy makes it worse. Plz rmember a Festool Systainer box is only 40 x 30 cm in footprint (15.75 x 12 in.)
Awesome. I recommend to add a Tajima Scraper. Love it and use it all the time.
As many others I just found your channel through your latest and probably first viral video. Crazy how viral it went. The content is pretty cool though. Do you think the comment from stuff made here boosted the virality a lot?
Awesome setup I have a few questions I am hoping you can answer!
What festool systainer are you using on top with the open tool storage? What are the tool dividers in the video for your pliers and screwdrivers?
What is the attachment for your Bosch drill driver that allows it to hang off the systainer? Thanks great ideas 👍 💡.
I think he mentioned the inserts in the tool caddy were 3d printed. The open top tool box with the handle is listed as a "tool box" on festools website.
The metal hook comes with the drill.
This is the most German thing I've ever seen
You haven´t seen the trash train yet!
@@MaxMakerChannel Do u show that? Or you're going to in the future?
@@el_micha Its on my channel! Got 4 million views : )
@@MaxMakerChannel I watched it now. Amazing!!!
I want a cart full of tools but I have to buy all those tools first, before I get the cart.
Great build, Where did you get those inserts for tool storage in top toolbox?
Hey, I 3D printed them!
TITLE SHOULD BE I BOUGHT A BUNCH OF STUFF..
Did you 3D print the organizer inserts yourself? I'm looking to purchase or have these exact parts made.
Yes I did!
Woher hast du die Einsätze/ Halterung her für dein Werkzeug, was du in der kiste verklebt hast? Aus einem 3D Drucker?
Würd mich über ne kurze Rückmeldung freuen!
Ja alles gedruckt!
Very inspiring! Would you mind sharing about that square light you mentioned? Forgive me if this is address elsewhere!
Hey, yeah it is a camera light for filming. There are a lot of chinese models out there. I connected it with a camera accessory gimble. So 100% camera equipment.
Echt toll gemacht. Daumen hoch.
Wie hast du das Innenleben von dem obersten Werkzeugkoffer gemacht?
Danke. Alles 3D gedruckt.
How many feet is that 3 meter tape measure?!
I don’t know. I had to measure that.
12 Banana's or 13 , depends on if you are left or right handed
Three Bushells
I am surprised you did not have a voltage tester pen
I added once since then!
Very cool! Do you have a linke to these small camera quick change adapters? Thanks!
You can find it if you google Aluminium Camera Mini Quick Release.
@@MaxMakerChannel Hi Max, amazing setup! I cant seem to find it. Can you please send us a link? Thanks in advance.
Only in the German Amazon store. The brand name is Neweer.
Прикольно 👍🏻
Hey @Max Maker,
kannst Du bitte Link geben für die LED Lampe und den Winkel Halter ?
Danke ;) gerne Amazon GER
Hallo Max wirklich cooler werkzeugwagen. Hast du mal überlegt wie bei Alexander Chappel 3d gedruckte Container zu machen? wenn es ok ist wollte ich auch fragen was du studiert/ als Ausbildung gemacht hast. bin fast mit der Schule fertig und suche gerade Inspiration.
Hello Max really cool toolcar. Have you seen the organizer boxes of Alexander Chappel? I think they could be a useful addition to your shop. If it's ok I wanted to ask what job you studied for? I'm almost finished with school and was interested. I am still in the searching phase and looking for ideas and inspiration.
Hey, diese Container sind ganz cool, aber wir haben davon jede Menge ähnliche Sortimentkisten von Auer-Packaging.com. Die haben 70 cent bis 4€ gekostet und waren am Ende deutlich günstiger und wir mussten nicht tagelang den 3D Drucker blockieren.
Ich habe Produktentwicklungsingenieur in England studiert. Das war genau das richtige für mich, aber ich glaube Programieren hätte mir auch gut gefallen. Hauptsache du machst etwas was du interessant findest. Gerade Handwerker sind gefragt wie nie. Ob Klinatechniker oder Dachdecker.
Viel Erfolg!
@@MaxMakerChannel Danke
maannn you didnt share any stl files wutttttt grince
What is the brand of your rivnut gun?
@Gesipa
This is a great idea, unfortunately this Festool stuff is extremely expensive here in US Murica. Each one of those sections is like $60.
Yep. Same here, but it’s justifiable for me since it saves so much time that it makes up for the price in no time.
K-nipex, you're GERMAN :-)
Love the cart though, I love systainers
can you share the 3d files? thanks!
"Perect" ?
This is sooooo german!
Zipties ;)
Hallo Max Maker
Sie sind Deutscher und sprechen in Ihrem Video nur Englisch.
Warum?
Ich bin mir jetzt nicht sicher.
Ist Ihr Video ein Englisch Sprach Kurs Video?
Oder soll Ihr Video ein selbst mach Video sein?
Sie würden mir eine Freude machen wenn Sie Ihr
Video Kunstwerk noch mal in Ihrer Muttersprache
Deutsch machen könnten.
Mfg ✌️
Das hat zwei Gründe. Zum einen erreiche ich dadurch ein größeres Publikum und zum anderen bleibe ich in Deutschland privat.
Ready for ANY job? How about welding- watch that plastic melt...
can you share the 3d files?