Thank you for the informative video. Going forward, it would be nice if you could film the tufting 🔫 gun to fill the screen. Zoom in so I can easily see the small details you are talking about. Your instructions were easy to follow and I liked that you wrote information as you were talking.
Hello Jenny! You explain it very clearly. I just didn't see which part of the scissors should be at a height of 18mm from the pusher. Do you mean the very tip of the scissors or the corner? I am grateful in advance for the answer!
I try to adjust pile hight to 10mm. When I adjust pusher - scissors to 10mm and lower bar to 45mm the pusher still sticks out too much from the foot at least 7mm. Any ideas what to do?
Здравствуйте Дженни! Вы очень понятно объясняете. Не увидела только, какая часть ножниц должна быть на высоте 18мм от толкателя. Имеется в виду самый кончик ножниц или угол?
Hello I want to buy an original machine from which site did I buy the original machine? What are the best specifications of a large carpet spinning machine? Thank you and all respect and appreciation to you
I watched an other tutorial, (not from you) and then watched this one.. the other video missguided me and tried to fix my gun by watching this and ended up doing worse.. I don't know what I can do to repair it.. do you know any adress where I could possible send it to get it put to the normal settings again? I'm prepared to pay for any shipping & repair cost.. but need it fixed 😩😩
Hey there, where do you live and do you have an original AK-I? I think you should be able to probably fix it with our tutorial since we go through all the general settings as well. You can also send me an email to help@tuftinglove.com with some pictures or a video explaining the problem. I'm sure we can make it work :) best Jenni
@@Tuftinglove thank you for your kind and quick reply! I live in Luxembourg and I do have an original AK-I Cut Pile gun. I'll try again, but it doesn't look good.. if not, I'll write you an email, thank you very much. Best regards,
Hey I adjusted the gun to highest pile height settings as per your video but the pile height of the yarn is still only 10mm is there anything else I can adjust to fix this?
Hey Mieke, you can follow the scissors exchange tutorial. Underneath the scissors there is the counterpart of this little screw. So you can fix it back together :) ruclips.net/video/4xTfyNnSJxU/видео.html
That's the pusher www.tuftinglove.com/de/collections/ersatzteile/products/ak-i-pusher-3er-set-1 it's the part that comes out together with the scissors
Hey, what part are you strugglening with? You can also slow down the speed in the player setttings in case that would help. also feel free to send an email to help@tuftinglove.com with pictures of your problem :)
Just some advice, you should never adjust the threaded rods on any tufting machine. This really puts people that do this in a tight spot as you can not easily revert back as it is now set at a random length.
Thank you for the informative video. Going forward, it would be nice if you could film the tufting 🔫 gun to fill the screen. Zoom in so I can easily see the small details you are talking about. Your instructions were easy to follow and I liked that you wrote information as you were talking.
Thanks a lot , this is the best tutorial in the entire of RUclips videos ❤
Is it possible to get a video with a closer look? It is hard to see the tiny parts and measurements you are referring to from the camera distance.
Hello Jenny! You explain it very clearly. I just didn't see which part of the scissors should be at a height of 18mm from the pusher. Do you mean the very tip of the scissors or the corner? I am grateful in advance for the answer!
The corner :)
I try to adjust pile hight to 10mm. When I adjust pusher - scissors to 10mm and lower bar to 45mm the pusher still sticks out too much from the foot at least 7mm. Any ideas what to do?
I didn’t do this and I’ve been using it for a day. Can I still do this?
these vids helped me become besties with my machine thank you!
Can you do the same with an Ak-II?
So helpful!!! Thanks
Hi, can u plss shows the yarn length for both heights? my machine is on the highest setting and I want to see if it's worth the hustle to adjust it
Здравствуйте Дженни! Вы очень понятно объясняете. Не увидела только, какая часть ножниц должна быть на высоте 18мм от толкателя. Имеется в виду самый кончик ножниц или угол?
your channel is excellent great advice on everything thanks my darling :)
thank you for this one!
Maybe it makes end to the eternal fight Upper rod vs Lower rod adjustment :))
This video saved me
Hello
I want to buy an original machine from which site did I buy the original machine? What are the best specifications of a large carpet spinning machine?
Thank you and all respect and appreciation to you
It is from our shop www.tuftinglove.com We do ship international and only sell the original AK.
@@Tuftinglove
Thank you 💗
Helped me a lot!
Thank you this was important to me 👍👍
This.is.so.useful! Thank you!
You're welcome!
I watched an other tutorial, (not from you) and then watched this one.. the other video missguided me and tried to fix my gun by watching this and ended up doing worse.. I don't know what I can do to repair it.. do you know any adress where I could possible send it to get it put to the normal settings again? I'm prepared to pay for any shipping & repair cost.. but need it fixed 😩😩
Hey there,
where do you live and do you have an original AK-I?
I think you should be able to probably fix it with our tutorial since we go through all the general settings as well.
You can also send me an email to help@tuftinglove.com with some pictures or a video explaining the problem. I'm sure we can make it work :)
best
Jenni
@@Tuftinglove thank you for your kind and quick reply!
I live in Luxembourg and I do have an original AK-I Cut Pile gun.
I'll try again, but it doesn't look good.. if not, I'll write you an email, thank you very much.
Best regards,
@@sirchill9991 send it to tuftingshop, they are from Netherland. Or google how to set it to default.
Hey I adjusted the gun to highest pile height settings as per your video but the pile height of the yarn is still only 10mm is there anything else I can adjust to fix this?
same
Why is my tufting gun keeps cutting my yarn
And do you have a solution when you have unscrewed the small screw too far? 😞
Hey Mieke,
you can follow the scissors exchange tutorial. Underneath the scissors there is the counterpart of this little screw. So you can fix it back together :) ruclips.net/video/4xTfyNnSJxU/видео.html
Argh what part is the pusher?
That's the pusher www.tuftinglove.com/de/collections/ersatzteile/products/ak-i-pusher-3er-set-1
it's the part that comes out together with the scissors
Graciassss 🤞🏼
Отличное видео! Ты лучшая:*
This video isn’t zoomed in enough and I am having a heck of a time following what you mean
Hey, what part are you strugglening with? You can also slow down the speed in the player setttings in case that would help. also feel free to send an email to help@tuftinglove.com with pictures of your problem :)
Just some advice, you should never adjust the threaded rods on any tufting machine. This really puts people that do this in a tight spot as you can not easily revert back as it is now set at a random length.