Many thanks for showing the correct way at 04:05 to place the black Support Flange (F) on top of the blade as the picture in the manual is tiny and does not clearly show which way up that it is supposed to be fitted. Very useful. It is also worth pointing out at 05:40 that the silver hex nut is the grease port for the bevel gear which will be needed upon servicing.
I'm not at all convinced that the way shown is correct. If the shallow boss on the support flange locates inside the blade then the support cup self-centres on the splines of the shaft rather than floating about vaguely as it does later in the video. This is because the support flange sits lower thus allowing the support cup to locate on the splines. Very poor manual from Husqvarna. Blade attachment is CRITICAL. Who wrote it? Ikea?
@@TheRunereaper I am in agreement with you. The video shows the flange disc installed incorrectly. The raised part of the flange disc should sit comfortably in the blade hole. The manual states this explicitly. I agree too with your remarks about the poor quality of the manual. I found several obvious inaccuracies.
@@SFFXd I thought I was the only one. The manual is terrible. The support flange is referred to in several different ways throughout. And, it is not well articulated how the flange should go. It would seem that the raised part of the disc should face inward, towards the blade, in that hole; however, the pictures indicate that the flange should be flush with the blade, this is better achieved when the raised part faces away from the blade, so that the smooth side of the flange rests against the blade. Also, in the pictures for the trimmer and the grass blade, it shows that smooth cover over the drive disc; however, in the saw blade attachment, it shows no cover over the drive disc as you can see the 3 holes exposed. I always use the cover. Finally, I cannot get my support cup to sit flush to the grass blade when the flange is between the blade and the cup. The outside edge of the cup does not make contact with the grass blade, so I just go without that outer cup. With that said, the 545 (mine is the 545fr) is still one of my most used tools around the property; it makes quick work of the vines, saplings, stilt grass, you name it, a must have if you are on steep and/or rocky ground.
Bel decespugliatore.. Il migliore
E ' vero!
@@zemlechist3789 Thank you Roma!
Thank you very nice comment Luca!
Por qué no mejor la 555rxt también de Husqvarna, trabaja muy bien, solo le faltó arrancarla amigo, para escuchar ese motor.
Many thanks for showing the correct way at 04:05 to place the black Support Flange (F) on top of the blade as the picture in the manual is tiny and does not clearly show which way up that it is supposed to be fitted. Very useful. It is also worth pointing out at 05:40 that the silver hex nut is the grease port for the bevel gear which will be needed upon servicing.
I'm not at all convinced that the way shown is correct. If the shallow boss on the support flange locates inside the blade then the support cup self-centres on the splines of the shaft rather than floating about vaguely as it does later in the video. This is because the support flange sits lower thus allowing the support cup to locate on the splines. Very poor manual from Husqvarna. Blade attachment is CRITICAL. Who wrote it? Ikea?
@@TheRunereaper I am in agreement with you. The video shows the flange disc installed incorrectly. The raised part of the flange disc should sit comfortably in the blade hole. The manual states this explicitly.
I agree too with your remarks about the poor quality of the manual. I found several obvious inaccuracies.
@@SFFXd I thought I was the only one.
The manual is terrible. The support flange is referred to in several different ways throughout. And, it is not well articulated how the flange should go.
It would seem that the raised part of the disc should face inward, towards the blade, in that hole; however, the pictures indicate that the flange should be flush with the blade, this is better achieved when the raised part faces away from the blade, so that the smooth side of the flange rests against the blade.
Also, in the pictures for the trimmer and the grass blade, it shows that smooth cover over the drive disc; however, in the saw blade attachment, it shows no cover over the drive disc as you can see the 3 holes exposed. I always use the cover.
Finally, I cannot get my support cup to sit flush to the grass blade when the flange is between the blade and the cup. The outside edge of the cup does not make contact with the grass blade, so I just go without that outer cup.
With that said, the 545 (mine is the 545fr) is still one of my most used tools around the property; it makes quick work of the vines, saplings, stilt grass, you name it, a must have if you are on steep and/or rocky ground.
which is stronger husqvarna 545 or stihl fs460
SUPER!!! LIKE!!! THIS IS JUST BEAUTIFUL!!!
Thank you very nice comment!
Чем она отличается от 545rx ???
Beautiful tools
Thank you very nice comment Mario!
For 545rxt autotune recomended oil xp or hp?
what type of screwdriver is used to adjust the husqvarna 545 rx carburetor
Триммер супер
Thank you!
Brilliant video. Cheers.
Thank you very nice comment!
Yo tengo 555 muy potente su defecto es q c calienta mucho el cabezal ojalá tenga otro diseña dónde la lubricación se haga más fácil
De cuantos cc es
C calientan mucho del cabezal y grasa q c le pones no le llega