Do you have any future plans on covering assemblies and multibody parts? Also a quick tip explaining hole options in parts? Such as linear and diameter etc... Thank you for all the hard work please keep it up!
@@CADxTraining got it sir ..I used The extrude feature now .. it worked ..but can I know the reason sir why rib feature is not working in swept blend method
@@CADxTraining yes sir while doing swept blend .. the surface was not fully closed to do rib feature ... So like u said I did extrude instead of rib ... Thank u for helping me out sir .. learning a lot from u daily
Sir ..you make sketch from a 2d drawings..where all dimensions are given..but you take dimensions very fast from that drawings . Our mind don't get it.
You can pause the video sometime in between to understand the topic better. I don't indicate dimensions all the time to reduce the length of the video. That is why I keep the drawing open all the time on the screen. Hope you can understand the reason.
I have considered it 50 degrees as it gives me the best result. Actually it should be tangent there. But I was getting some error when I was using tangent condition there. So I considered 50 degrees to get the result.
This part consumes lot of time because of tiny features thanks sir learn something new today
Dear Mr Satinder
Your tutorials are great ❤️
Muchas gracias por enseñarnos a conocer este software.
Thank you very much sir for sharing your immense knowledge with everyone one....
Thanks sir nice explanation
Super sir... Thank you...
Thank you! You are the best!
Do you have any future plans on covering assemblies and multibody parts? Also a quick tip explaining hole options in parts? Such as linear and diameter etc... Thank you for all the hard work please keep it up!
Yes, it's coming soon.
Thanks sir
Right click and hold for half a second for the dropdown menu to appear.
Sir you have added the part drawing next to the model tree. Can you guide me how to do that ?
Sir do u hve practise exercise from start to end which cover all function one by one
Sir, How you mentioned the centre line for rib sketch
Please explain!
I have taken it as approx value
How to keep the drawing on the left as you did in creo?
This is done by video editor
@@CADxTraining Thank you so much sir, Your videos are so helpful.
sir how to add pcd as shown in this drawing
There is no direct method in Creo parametric to do this. You can only do this by adding a draft entity.
sir can u please try swept blend method ..i tried swept blend to create the part but i cant able to create the rib feature
If you are following swept blend method then at the rib using extrude.
@@CADxTraining got it sir ..I used The extrude feature now .. it worked ..but can I know the reason sir why rib feature is not working in swept blend method
The surface generated by swept blend is different than extrude and revolve.
@@CADxTraining yes sir while doing swept blend .. the surface was not fully closed to do rib feature ... So like u said I did extrude instead of rib ... Thank u for helping me out sir .. learning a lot from u daily
Keep learning
Sir in my creo 7 when i use "Skecher pallets" then i received "fatal error -traceback error"
Get only when sketcher pallets i use
There is some technical issue. Uninstall creo and try to reinstall.
@@CADxTraining it occurs every time i reinstall so many times
You try any other version to check
@@CADxTraining i checked 5 6 7 8 version
Than this will be the graphics related issue
Overall fantastic . super..but where is the dimensions in the sketch page. Show as during sketching .
I didn't understand your question.
Sir ..you make sketch from a 2d drawings..where all dimensions are given..but you take dimensions very fast from that drawings . Our mind don't get it.
You can pause the video sometime in between to understand the topic better. I don't indicate dimensions all the time to reduce the length of the video. That is why I keep the drawing open all the time on the screen. Hope you can understand the reason.
Ok sir ji ...your all videos are great upper thanks a lot.
22:19 how did you derive 50 degrees?
Love your videos!
I have considered it 50 degrees as it gives me the best result. Actually it should be tangent there. But I was getting some error when I was using tangent condition there. So I considered 50 degrees to get the result.
@@CADxTraining understood thank you for the explanation
Start point and blend vertex not coming while right click
Just right click will not work. Right click and hold the right click, you will get the options.
During video all time dimension sketch is showing which cover half area of display that is annyoing