Witch one is better....? I have the m52 on my 728i .....260.000 km and purrs like a kitten......i dont abuse it ....last year i put a lot of new parts ....water pump....radiator...hoses....belts....motor mounts .....new coolant....new oel in gear box....and at the m52 i use castrol 0w-40 every 8.000 km.......in the same time i have an 740iL......but with that anather story......
Just put a turbon on it and a cooper ring head gasket and give it e85 and you can have 600whp with no problem with stock engine, i run that setup myself :) stock engine with arp for the head, and cooper-ring head gasket, the rest is stock in the enginge ;)
Great work ! I have an E36 first generation actually built in 91... needless to say it comes with this engine the M50B25. I love this car, and I have taken care of it well inside out. I plan on getting it turboed in the future. However with my Euro chip it runs fantastic with all the untapped power. Thanks for the post !
@@Xrissy10 This may be quite late but I own a 1992 325i and you can buy a chip to make extra horsepower. Make sure you match the manufacturer date with the chip to make sure it will work. Some cars are OBD2 and others, like mine, are OBD1. Miller performance offers a chip for $400.
Fantastic work and wonderful attention to detail. This is an inspiration and makes me want to post my motor to Ebbtech to have this work done. Very nice skills!
there is no words to describe how amazing is you job and i have been watching a lot of your videos on your channel , and i would love to see a video for this engine running :)
Very nice! Head work is next on my to do list w/ my M50 turbo... Topping out at 489hp w/ my T70 @ 16psi. Only thing I've done to my top end are springs and retainers :/ Would love to get rid of this Cometic MLS and go with a copper wire if only for longevity purposes.; but I'm saving that for when I stroke her out...probably next this time next year.
I just bought an e36 recently and needs some big check up and changes in the engine. I’m already looking into part prices but I’m curious on how much this whole process must have cost…..
i would say little bit over kill to do full ports and polish etc. but that is never a bad thing, i would be those also. and yet 600hp dont need all that
i have m50b25 engine, I am thinking about to put a crank chaft and rods of m54b30 with pistons from Opel Omega thay have a 86mm ,with modify original pistons and Remove some Millimeters from engine block, Afraid of high temperature and compression ratio, what do you think of the idea, what do you recommend?
Hi @EBBTECH MOTOR, At 3:08 You are polishing inlets, Im doing same head now for my 600bhp engine build. Could You please advise where can I purchase long tips/heads like at 3:08 so I can do my inlets properly. I was looking everywhere and cant find them. I mean the shaft plus buffing/grinding tip ( cone ) Please help. Thanks !
How much money would you have to pay for someone to do all this work for you? And how many hours did it take for you to turbo charge the car and for it to be fully functional from scratch. Cheers
@@EBBTECHMOTOR I didnt do anything to my m50 head for nearly 700whp, only ARP to the head and Cooper ring head gasket and ive made 663whp 881wnm on my m50 2,5L stock bottom end, and stock head.
Hi, im building a turbo M50 myself rn, im worried that the stock exhaust valves cant withstand the increase in power. I got 6mm M50Tu Valves. Im thinking about buying Supertech Inconel (~500€) but im not sure if thats necessary, plus they are expensive af?
love this video, thanks for posting it. I'm curious if you have a link for all the tools needed to purchase if one was to do this. Also, do you recommend reusing the springs, or is there a way to verify whether they are good or not.
Brother its a amazing work. I have a question,its possible put double spring in my E36 M42 engine 318is? 318 is 1991 have 7mm valves and double spring. And. 318is 1993 have 6 mm valves and one spring. Its possible put double spring of 1991 in a cylinder head of 1993 ? Thanks and nice machines,haven't this good machines,pity :)
i have 520i m50b20 150HP 5speed manual - want to turbo it - is the stock gearbox and clutch going to be ok on such built ? what is the cost of turboing in the UK ? currently lowered the front by 40mm with AP springs , 18inch mv2 m-sport wheels - looks ok but I want it to be faster as 150 HP is not a lot...
Very nice, the M50 is one of BMWs best engines ever. Very strong and reliable.
it is a sturdy little engine for sure. Thanks
I have a m50 head on my m52 the m50 head has a few less ports but it seems like it would be harder to crack
I have m52 aluminium block is also good but not that solid
M52tu
Witch one is better....? I have the m52 on my 728i .....260.000 km and purrs like a kitten......i dont abuse it ....last year i put a lot of new parts ....water pump....radiator...hoses....belts....motor mounts .....new coolant....new oel in gear box....and at the m52 i use castrol 0w-40 every 8.000 km.......in the same time i have an 740iL......but with that anather story......
The 1992 M50 is the way to go. Yea you gotta keep the revs up, but when you do - nice!
ok and thanks :)
I have a 93 E34 BMW with the M50 and I can't wait to have a built engine
Just put a turbon on it and a cooper ring head gasket and give it e85 and you can have 600whp with no problem with stock engine, i run that setup myself :) stock engine with arp for the head, and cooper-ring head gasket, the rest is stock in the enginge ;)
and a good tuned ecu ;)
@@josearevalo1765 Yes ofc, thats the most important of them all :)
@@FernisProductions1 Hi there. What did you do for tuning? Stock ecu or aftermarket? What psi are you at? thanks in advance
@@FirstAidIndustries i use VEMS ecu, stock sucks. Right now 1,8 bar, dont know what that is i psi but around 30.
Great work ! I have an E36 first generation actually built in 91... needless to say it comes with this engine the M50B25. I love this car, and I have taken care of it well inside out. I plan on getting it turboed in the future. However with my Euro chip it runs fantastic with all the untapped power. Thanks for the post !
Greatly appreciate you watching.
Ronald Quin
I have same engine.. can i change the chip... can u elaborate more pls
@@Xrissy10 This may be quite late but I own a 1992 325i and you can buy a chip to make extra horsepower. Make sure you match the manufacturer date with the chip to make sure it will work. Some cars are OBD2 and others, like mine, are OBD1. Miller performance offers a chip for $400.
Fantastic work and wonderful attention to detail. This is an inspiration and makes me want to post my motor to Ebbtech to have this work done. Very nice skills!
Thanks for watching.
there is no words to describe how amazing is you job and i have been watching a lot of your videos on your channel , and i would love to see a video for this engine running :)
Thanks alot for those kind Words Sir. i might put a video of this engine when it races :) EBB TECH
EBBTECH MOTOR i just said the truth Brother :) , and can't wait to see the video ^_^
awesome man! that precision just insane..
really like it..
+speedfreaks14 Happy to read that Sir and thanks.
EBBTECH MOTOR where you located? I need this don edd to my m50 cylinder head.
Holy Jesus I wish I could experience the luxury of owning one of your finished heads. I have a m52b28 you can do.
Attention to detail! superb engineering.
Thank you for that and Greetings from EBB TECH
This is auto porn!
Thanks for that MIA :)
youre welcome, i have a BMW M54B30 head i want to turbo also, where are you located?
exactly what I thought after watching this video.
Very nice!
Head work is next on my to do list w/ my M50 turbo... Topping out at 489hp w/ my T70 @ 16psi.
Only thing I've done to my top end are springs and retainers :/
Would love to get rid of this Cometic MLS and go with a copper wire if only for longevity purposes.; but I'm saving that for when I stroke her out...probably next this time next year.
Thanks Jake :)
Super. I wish to use my vacations to spend in such workshop and to learn and live between engines :)
Just present yourself to a machine shop , work for free to learn. That is how i started :). Thanks for watching.
Thank you so much for this. Many of use want to have parts machined but don't understand the work behind the cost.
+Djmack199o Thanks a lot for watching and for commenting. EBBTECH.
Amazing work! I would love to have the skills and tools to accomplish this level of detail every day.
Appreciate you watching
that is some awesome porting job there
Thank you for comment and watching :)
bellissimo lavoro...vi contattero' al piu presto..complimenti
Thats interresting video, really nice craftmanship!
+Antti Uusitalo Thank You for watching and for comment Antti
In the beginning You found same small cracks. How did you checked them later? Were them welded?
I just bought an e36 recently and needs some big check up and changes in the engine. I’m already looking into part prices but I’m curious on how much this whole process must have cost…..
In a world of cnc its great to see old school porting and flow techniques
Thank you my friend.
WHAT a perfect job
Thank You and thank You for watching.
where are u from ?
i want the same preparation on my 525i e34
nice build
Norway. Thanks.
i would say little bit over kill to do full ports and polish etc. but that is never a bad thing, i would be those also. and yet 600hp dont need all that
Whats the pricetag for something like that?
More than you can afford asshole.
@@Jet3ch pretty smart answer! Is your M54B30 turbo swapped after 4 years, or was it not affordeble for you? :D
@@MeinNameistFlo haha its a line from the movie Fast amd furious, the first one....
@@Jet3ch oh in this case... i didn't get it, never watched the movie in english, just in german :D
@@MeinNameistFlo Then it's "mehr als du je haben wirst!"
I see more precision machining in this than in most videos about cylinder heads. Were those valves new or were they factory valves that were machined?
i believe that he just cleaned the factory ones and machined them
OEM valves just refurbished i think. Thanks.
@@EBBTECHMOTOR Thanks.
i have m50b25 engine, I am thinking about to put a crank chaft and rods of m54b30 with pistons from Opel Omega thay have a 86mm ,with modify original pistons and Remove some Millimeters from engine block,
Afraid of high temperature and compression ratio, what do you think of the idea, what do you recommend?
Hi @EBBTECH MOTOR,
At 3:08 You are polishing inlets, Im doing same head now for my 600bhp engine build. Could You please advise where can I purchase long tips/heads like at 3:08 so I can do my inlets properly. I was looking everywhere and cant find them.
I mean the shaft plus buffing/grinding tip ( cone )
Please help. Thanks !
Home made i am afraid :) Thanks
I thought valvework wasn’t really needed to make big power with m50. Maybe I’m thinking more m50tu/m52
Nice , pretty and amazing
Appreciate you commenting and watching.
А норвежцы,помимо качественного Black Metal,умеют и турбо моторы строить.Удачи!
Thanks my friend :)
Very good job!
Appreciate Your comment and for watching.
How much money would you have to pay for someone to do all this work for you? And how many hours did it take for you to turbo charge the car and for it to be fully functional from scratch.
Cheers
Well that depends on many factors. Thanks for watching.
Where do you learn to do this stuff? I think a job like this would be so statisfying
It is kind of cool to do yes. Thanks
You need to bed the valve to the valve seat
nice job man!! thats a really good work righ there , i really wish that i will do a lot of this awsome ART someday soon ;)
+Abdelkefi Mohamed Lotfi I thank You for that Sir and thanks for watching.
Does this head can only make engine 600Hp? I think with high enough boost it can make more.
We have made engines With heads like this above 800 HP. Thanks for watching
@@EBBTECHMOTOR I didnt do anything to my m50 head for nearly 700whp, only ARP to the head and Cooper ring head gasket and ive made 663whp 881wnm on my m50 2,5L stock bottom end, and stock head.
@@FernisProductions1 can 850 be broken with M50 on stock internals?
@@rahimmuradov635 i dont think the engine will be in 1 piece for so long :D
Just had this same thing done to my head for $350
+BikerFail16 Thanks for watching EBBTECH
is that a high or super rare low price?
Awesome man .
Appreciate you watching and commenting :)
Hi nice work,does this BMW M50B25 TURBO 600HP SERVE for a BMW E30 1985 MODEL,I have everything Forged already & I want to get more horse power
In a E30 or corolla 1980👌
Hi, im building a turbo M50 myself rn, im worried that the stock exhaust valves cant withstand the increase in power. I got 6mm M50Tu Valves. Im thinking about buying Supertech Inconel (~500€) but im not sure if thats necessary, plus they are expensive af?
Well new valves could be good. Thanks.
love this video, thanks for posting it. I'm curious if you have a link for all the tools needed to purchase if one was to do this. Also, do you recommend reusing the springs, or is there a way to verify whether they are good or not.
amazing work
Thanks my friend
Круто! У меня такой же движок ))
Brother its a amazing work.
I have a question,its possible put double spring in my E36 M42 engine 318is?
318 is 1991 have 7mm valves and double spring.
And.
318is 1993 have 6 mm valves and one spring.
Its possible put double spring of 1991 in a cylinder head of 1993 ?
Thanks and nice machines,haven't this good machines,pity :)
i have 520i m50b20 150HP 5speed manual - want to turbo it - is the stock gearbox and clutch going to be ok on such built ? what is the cost of turboing in the UK ? currently lowered the front by 40mm with AP springs , 18inch mv2 m-sport wheels - looks ok but I want it to be faster as 150 HP is not a lot...
You have a getrag 220 that clutch won't hold get a stage clutch or go with 5zf
I'm impressed have you guys done any 4 cyl head work and where are you located
Yes. go into my web page : ebbt.no and you can see lots of different projects.Situated in Norway and shipping all over the world. Thanks
Nice- Clean Job :)))
Thank you.
Hey, do you have experience to port and upgrade bmw m57 head for single turbo??
Or eaven some info about it. Thanks
fucking awsome from a spark in my hearth in a wild flame !!!
oki. Thanks for that then :)
hey i have a question im looking for a m50b25 non vanus is it good for turbo or what shuld i look for ??
m50 engine is perfect for turbo..
great work, where are you stationed
+Christiaan Roos I am located in Norway Sir. Do work for all over the world. Thanks.
@@EBBTECHMOTOR how much does a job like this cost these days?
why it has two valve springs? Normally it has only one , two came from m50b20 ? is it better valve springs then 2.5?
Aftermarket high performance parts. Thanks for watching.
i think that both M50 pre-vanos versions had double springs
What did you spray on the head before you put it in the parts washer?
Kind of my own little mix you could say :) Thanks for watching.
is there a tool kit you use to do the exhaust and intake porting?
Not that i know of. Thanks for watching.
I'm pondering building an m50 myself. What can one do to pull more revs out of it?
more throttle ) Thanks for watching.
Can you tell please average price to prepare an m50 engine for customer like u did on the video?
All pricing done by mail. Thanks for watching. EBB
How much does this cost? Thanks great video great job
+DAVS Gaming It Depends on customers requirements. Feel fre to mail me for a quote. Thanks for watching.
Thought there was an alien at 5:39
ok and thanks :)
круто :) я занимаюсь BMW, заходите в гости !
Just give me a mail or Call and i`ll take care of it :) Thanks
i would never drive that head hahah nice nice
Thank you for taking time to watch :)
could the same be done with an M54
Как с вами можно связаться ?
Sublime!
How much euro is this gonna cost? Same treatment as the video.
All pricing only given by mail. Thanks.
How much do you charge for this? I'm in the US and might be interested.
+August Norman Send me a mail and ill figure something out. Have one like this for sale right now.
Just a question. Are those stock things can handle 600hp?
+DaBombtasi Yes ideed they can Sir. thanks for watching.
600 on E85 or 93/100 oct ?
Depends on owners preference i guess. Thanks.
Was that a 400-900 dollar job?
It depends on several factors. Thanks.
CNC god.
Glad you watched and thanks.
no computer numerically controlled anything was shown in this video, glad you watched and thanks
Bravo !
Thanks
A stock cylinder head is good for more then 600.
yes it is. And a modified is able to do even better job :) Thanks for watching.
what did you do to the cracks?
Crakcs can normally be welded or fixed in other ways. Thanks for watching.
Do you take clients from the U.S.?
Yes Sir i do. I have customers from many Places around the world. Thanks for watching.
moin .....schon Arbeit respekt.was werde mich kostet..
what do you think about forged pistons?and about exost pipes that say that gives engine more power?
Forged high compression pistons can be great and proper built exhaust will make more Power.Thanks and Greetings from EBB TECH.
Thanks you are doing great job y love the look of that cylinder head
Where it your location ? I would do rebuild E36 m3 .
Location : Norway , Stavanger. Thanks. EBB
do you do international shipping? How much your labor for rebuild e36 M3. thank you bro
Достойно.
Thanks
How much cost for all ?
It Depends on build. Thanks
bmw n55 how much pless
Thanks for watching.
А как бы мне так сделать? Сколько стоит? Куда писать?
Thanks for watching
EBBTECH MOTOR he asked price and where to write lol
Where is this a 600hp cylinder head build
why? the m50 is a super common engine and cheap (atleast were i'm from) and easily flows 600hp untouched.. why all this work for basicly nothing?
Ready for customer to lap the valves himself??
Valves are not meant to be lapped when seats are machined.
How much do you charge to do this
Al ldepends on detail Level. Thanks for watching
EBBTECH MOTOR for something just like this
Pris topp til m50b25vu?
Hei.Slå på trådenen dag for litt info. mvh EBB
dagtid du mener?
WHERE DID YOU GET THE VALVE SEAL TOOL I NEED THAT BITCH LOL
Cant remember :) Thanks.
hello very nice you can fix same this head and sell it i have my e34 m50 engine i want same this head ??
what the fuck this music?
+Kamil Wisniowski sorry to say my own. Got to have something,,right ? Thanks.
Top music =D
Dont polish ports :(
why not?
Thanks for watching.
very jealous
Thanks for watching.
Wtf is this song
Great one i think :) Thanks
Обычный ремонт гбц
Thankas
Jesus christ
Thanks for watching
did you do a top and bottom cut on the seat? for example 30,45,60 or similar?
i do all kinds of cuts :)