Thank you for making this video, it was the only video I needed to install this on my 17’ RT. Looks sick!! And I get how it can be hard to keep clean but the clear piece looks more aggressive from the outside rather than the inside in my opinion.
I got mine installed tonight!One of my riv nuts was just a tiny bit loose(the first hole I drilled out) but the Allen bolt tightened up just as all the others. Really happy with this product it looks amazing. One thing about drilling out the pilot holes to the final size that I wasn’t entirely ready for and I do have quite a bit of experience in drilling stuff. Once the bit goes into the hole it was catching and then instead of cutting it was pulling the drill into the spoiler as it spun. I was going slow and careful and it still pulled the drill in to where it was starting to hit the spoiler on the opposite side from the inside if I wasn’t being slow and careful it might of been catastrophic. I found that once the bit breaks through you have to stop and kind of pull back on the drill as you drill to get it to cut rather than it pull itself inside. The hardest part of this install is taping and measuring everything and making sure the spoiler is gapped on the pencils just right and getting the outer corners bent in and taped down. I measured the two inner riv but holes from outer edge of hole it was right about 10” marked the center at 5 lined it up the best I could. Measured with seamstress tape from the inside angle of the top of the wicker bill right above those slots to the outer tip of the srt spoiler to make sure it was dead nuts center.
Great video and thanks for sharing. I received mine and already installed it. Can I remove the smaller middle piece and leave the one that mounts to the factory spoiler?
Thanks for the how to video Jerry I am going to help my son install his in the next couple of days we will tag you with pictures Just some input maybe your next video you can have a camera person so they can get a close up of what you're doing and maybe if you could on video do 2 or 3 of The rivets for example so we can get a better rhythm and understanding from our point of view. Thx
the first rivnut i put in went perfectly fine felt amazing about it when i took the tool off i accidentally dropped it and put it back together as i saw it on the video then i began to do the other ones none of them wanted to tights the rivnut and the star washer were all turning together when trying to tighten. what do you think is the problem?
I installed mine myself and was pretty easy. I had a hard time finding a 25/64 drill bit and had to put my math skills to work and found out the 3/8 drill will work.
How did you center the bill? Im going to use a pieces of 3m double sided tape along with the screws once I make the holes to ensure good holding strength. Just my preferation when i recieve the bill.
Hey man, I’ve been trying to get in touch with you about a hardware issue I’ve had with my order. I’ve called your number a few times now and left voicemails each time. Thanks!
I bought a different wickerbill. But you had the best instructions! I never used a rib nut before or anything! Great video thank you
Thank you for making this video, it was the only video I needed to install this on my 17’ RT. Looks sick!! And I get how it can be hard to keep clean but the clear piece looks more aggressive from the outside rather than the inside in my opinion.
Sold 10,000 3 years ago. Millionaire. Acrylic wickerbill, amazing idea! Im up next!
Nice thanks for all the advice. I bought this exact spoiler for my charger and I love it. Appreciate you.
Perfect timing, just got mines today, for my charger can’t wait to install
mines? typical english for your kind
Just got my order from you guys and just installed it my self . Thanks for the video helped me a lot . Looks mean as hell thank you jerry
Thanks got mines Installed today.
I got mine installed tonight!One of my riv nuts was just a tiny bit loose(the first hole I drilled out) but the Allen bolt tightened up just as all the others. Really happy with this product it looks amazing. One thing about drilling out the pilot holes to the final size that I wasn’t entirely ready for and I do have quite a bit of experience in drilling stuff. Once the bit goes into the hole it was catching and then instead of cutting it was pulling the drill into the spoiler as it spun. I was going slow and careful and it still pulled the drill in to where it was starting to hit the spoiler on the opposite side from the inside if I wasn’t being slow and careful it might of been catastrophic. I found that once the bit breaks through you have to stop and kind of pull back on the drill as you drill to get it to cut rather than it pull itself inside. The hardest part of this install is taping and measuring everything and making sure the spoiler is gapped on the pencils just right and getting the outer corners bent in and taped down. I measured the two inner riv but holes from outer edge of hole it was right about 10” marked the center at 5 lined it up the best I could. Measured with seamstress tape from the inside angle of the top of the wicker bill right above those slots to the outer tip of the srt spoiler to make sure it was dead nuts center.
Great video with a great wickerbill product
Got my wickerbill a few months ago, check... got the spoiler I wanted, check. Scared $#!+less to install 😆
very well explained
Great video and thanks for sharing. I received mine and already installed it. Can I remove the smaller middle piece and leave the one that mounts to the factory spoiler?
Thanks for the how to video Jerry I am going to help my son install his in the next couple of days we will tag you with pictures Just some input maybe your next video you can have a camera person so they can get a close up of what you're doing and maybe if you could on video do 2 or 3 of The rivets for example so we can get a better rhythm and understanding from our point of view. Thx
9:15 he explains exactly how it works.
the first rivnut i put in went perfectly fine felt amazing about it when i took the tool off i accidentally dropped it and put it back together as i saw it on the video then i began to do the other ones none of them wanted to tights the rivnut and the star washer were all turning together when trying to tighten. what do you think is the problem?
I installed mine myself and was pretty easy. I had a hard time finding a 25/64 drill bit and had to put my math skills to work and found out the 3/8 drill will work.
You sure? It’s a little smaller
Did it work with the 3/8? I dont have a 25/64 either in my kit either
3/8 didn't work!!
@@thegreatest1yetooooof
Nice install
Awesome video
How did you center the bill? Im going to use a pieces of 3m double sided tape along with the screws once I make the holes to ensure good holding strength. Just my preferation when i recieve the bill.
I was thinking about same the other day and going with the big drill bit at once … ???
That 25/64 bit stopped me in my tracks 😞 Gotta wait for Amazon now lol
Why not going straight with the big drill bit? I’m about to installed mine … please advice … thanks
Wish you have this made for 08 Cadillac sts V that would be a bad ass.
Love the WickerBill.. when are the strut tower braces getting released?
Can I use lock tight on those bolts doesn't seem very tight
I went to my local Home Depot and they don’t have the 25/64 drill bit . They had a 5/64 . I can’t find a 25/64
What size are the bolts I am missing one.
I purchased the v3 but was missing two of the washers. How can I get them?
Do you guys have a carbon fiber wicker bill? If so, can y’all send me where I can buy that?
I peeled the paper before drilling the holes will I have any issues?
What size is that ratcheting wrench or the socket you need for the rivnut tool?
ik im late but its an 11mm
I have a 2017 RT blacktop it has that wing can I install that on it
I DESTROYED A RIVET, ANY IDEA HOW I CAN GET THE CORRECT SIZE AND THE TOOL TO RIVET WITH?
Can I buy the bolts in black somewhere ?
Paint them
Whats the size of the rivnuts?
Does this fit on a 2016 Dodge Charger scatpack?
I ordered this over 7 days ago and still hasn’t shipped
good video but the beeping in the background is annoying , at first i thought it was my alarm going off lol
Too bad wicker doesn’t make this for other males and models. Wouldn’t mind running this on my Camry.
The first time ever
I like your working
Longest part was taking the cardboard film off the spoilers 😂
Hey man, I’ve been trying to get in touch with you about a hardware issue I’ve had with my order. I’ve called your number a few times now and left voicemails each time. Thanks!
gotcha taken care of Zach!!! thanks for the purchase!!
Yes sir, thank you so much!
Acrylic is garbage
I went to a body shop and they lost one of the bolts, what size are the bolts n washers ?