Hello. I need some help from you! I have the exact same card! The card has a design flaw in my opinion. Across L and R input there is 20k resistance and there are no input capacitors! The signal should have been mono wired at the output of the op amp ic. and not on input! 20k resistor over L and R can lead to nearer mono sound! If you take output from a preamplifier and run it into both an amplifier and a bass amplifier then 20k resistance over L and R is not good. There is also no capacitor on the input! What is your professional opinion on this! Be a little technical!
Why is mine so quiet, I have my amp wierd to the pcb and the sub wiers to the output on the pcb, does the output of the pcb need to hooked into another amp?
@@12voltvids thanks for the answer. My main amplifier has two channels , no subwoofer exit. Do i need a pre amp for the input of my dedicated subwoofer? T am thinking of those tube buffers you made in other videos . Would something like that suits ??
is their a good place online to buy those AC transformers? Ive tried googling them but not a large selection from any site I'd trust. I have a few, but most are way over 24v/24v , mostly salvaged from older electronics. also thanks for the close up of the board. those look like nice higher end components.
I saw the same butt hurt moron JOhn Senchak on BigClives comment section complaining about Clive sending him an invite to the Isle of Man for a meet up. What an idiot.
Hello. I need some help from you!
I have the exact same card! The card has a design flaw in my opinion.
Across L and R input there is 20k resistance and there are no input capacitors!
The signal should have been mono wired at the output of the op amp ic. and not on input! 20k resistor over L and R can lead to nearer mono sound!
If you take output from a preamplifier and run it into both an amplifier and a bass amplifier then 20k resistance over L and R is not good. There is also no capacitor on the input!
What is your professional opinion on this! Be a little technical!
Why is mine so quiet, I have my amp wierd to the pcb and the sub wiers to the output on the pcb, does the output of the pcb need to hooked into another amp?
Any alternatives how do i connect it to a power supply? I only have a male plug here
is this work with 400watt subwoofer specker?
If i have a subwoofer with his own amplifier inside. Do i have to use a pre amplifier ?? My main amplifier has two channels , no subwoofer exit
A dedicated subwoofer should have a low pass filter ahead of the amplifier.
@@12voltvids thanks for the answer. My main amplifier has two channels , no subwoofer exit. Do i need a pre amp for the input of my dedicated subwoofer? T am thinking of those tube buffers you made in other videos . Would something like that suits ??
is their a good place online to buy those AC transformers? Ive tried googling them but not a large selection from any site I'd trust. I have a few, but most are way over 24v/24v , mostly salvaged from older electronics.
also thanks for the close up of the board. those look like nice higher end components.
Hi can I use a headshet 3.5mm jack instead for the input and a 3.5mm jack for output?
Sure as long as the wire is shielded it should be fine.
Thank you for this great vid man :)
Where i can get that item my friend. ?
Link is in the description.
I' m just waiting for mine to arrive.
Equiped with the obligatory bright blue led, I see. They thought of everything.
Sir PDF
Thanks for your published video project. Appreciated. //^0^\\
4 videos in 1 day, watch out your trigger the but-hurt ppl....lol
I saw the same butt hurt moron JOhn Senchak on BigClives comment section complaining about Clive sending him an invite to the Isle of Man for a meet up. What an idiot.