Does your Boat Outboard Water Pump and Impeller Need Replacing?

AMAZON LINKS TO PRODUCTS FEATURED IN THIS VIDEO :
MERCURY OUTBOARD WATER PUMP KIT TOP HALF : amzn.to/3i7KCPl
MERCURY OUTBOARD WATER PUMP KIT FULL KIT : amzn.to/2B530YF
MERCURY IMPELLER ONLY : amzn.to/2YBblMo
Also Join me on:
Facebook: / fishingadventureshawke...
Twitter: @fishingAdventu6
If you are in New Zealand please support my business:
Best Baits in New Zealand: / lastcastnz
Contact Me:
Email: [e-mail]
Send me a Message on Facebook:
/ fishingadventureshawke...
Send Me Some Mail:
Contact me and I will Gladly give you my mailing address
How to service and replace the impeller and water pump on a mercury outboard motor.
Most outboard motors work on the same basic principals where the main shaft turns an impeller inside a water pump housing pumping water up and through the outboard motor, cooling the motor down...

[@FishingAdventuresHB]

With so many people passing through. It Would be pretty cool to know where y’all from let me know down here.

[@dirkastle216]

Hey! Great video. Thanks. I’m stuck with reinserting the drive shaft on my 1971 Mercury 1350. It hits with 1 inch prior to seating in properly. I thought it was the drive shaft but you mentioned the gear connector. Any advice on how to get either of those two aligned? Thanks

[@randalllawley1688]

Thank you for making an informed video about this entire water pump replacement

[@cschlesinger8596]

Rotate the drive shaft clockwise while pushing down on the pump housing. This will ensure that the impeller blade are deflected in the correct direction. Apply grease on the flat of the drive shaft to hold the key in place. Do not apply grease to the top of drive shaft, only on the splines. Applying grease to the top end on the drive shaft may cause a hydraulic and the shaft will insert completely. Just some thoughts.😁😁

[@michaelpryor2981]

adding grease to the O ring helps it last longer, adding a thin bead of oil on the impeller blades helps it a lot, due to a dry start up & as you put the impeller in the housing keep spinning it as you tighten it down so when it squishes down it doesnt get pinched at the bottom. make sure it turns freely...that happens all the time....and add a bit of green marine greese to all the bolts.

[@gtrapper3745]

Thank you for this tutorial it was very good, I’m from North Dakota!! God Bless !

[@GDKimble]

Watched this from Little Rock, AR!

[@pauljanssen7594]

Good job but should have put some water type grease on the lower o-ring and the propeller.

[@fanievanvuuren7771]

A good working demonstration.

[@FishingAdventuresHB]

Thank you 😁

[@Number1Cowboy]

you did that all wrong dude,when installing the top housing on the impeller turn the shaft clock wise and it will set right down on the impeller,never beat tha top housing down on the impeller,the tabs on the impeller have to be turned a certain way but the way you did it you just cramed the housing onto the impeller,

[@larryezell]

Mercury tech reps cringed when they saw him beating the housing down.

[@bulistik5039]

Not to mention no grease on the key to hold it in place or on the impeller or house.

[@joshuagreene9976]

Do the gaskets below the lower assembly need gasket sealer?

[@talebabuzwaid1346]

Thank you man nice working

[@keithmcpherson4001]

You didn't lube the impellar housing.

[@poktanbinabersama2264]

Saya dari Indonesia
Sulit mendapat kan barang untuk melakukan perbaikan

[@woodcreations101]

Love the shirt you have on bro!!! How do I get one? Do you only have shirts or do you have others as well?

[@FishingAdventuresHB]

Handy Man Lets Go will be working on it soon.

[@woodcreations101]

@@FishingAdventuresHB great stuff bro. 😎👌

[@diarbb5900]

Ireland 🇮🇪