i wondered about having multiple pieces of underlayment on a single row. i typically see a single piece from end to end. i think you are correct that some seam tape may fix it. i actually think its good Don found them. just seal the seams and wait for the next rain to test it.
@@WaywardOffGrid I think that's the only thing it can be, that underlayment is good stuff and it looks to be laid correctly. Only thing that I don't like is that patchwork seam at the ridge piece but some butyl tape will fix that too. Probably would have done a 1ft piece on both sides so that would make the ridge piece lay atop on both sides. But no worries, it'll be good to go. Crazy how much seam tape is now, I was shocked when we built our tiny house. I pray that I'm in Don's shape when I get there, what an inspiration! ~much love ❤
I hope Don is reading the comments BEFORE he takes action. I worry that because of the build up of the videos, he may have already scrapped what he did and tried something completely different. We shall see.
Don, just think. If it didn't rain, you wouldn't have known that there were any leaks once it's all said and done. You have taught me what grit means. I see the disappointment in your face, yet your determination lingers in your eyes. We are not going to give up on you so you shouldn't either. Teach that roof a lesson and we will be in your corner cheering for you the rest of the way.
Don, we all make mistakes and nothing is perfect. The good thing is it's always fixable. Keep in mind you're doing something most would never attempt. Be proud of what you have done and keep forging ahead. We are all behind you.
Don the peel and stick is a water and ice Shield not even mandatory under metal tar paper would work and would also leak if rained on directly so put the metal on and don't worry about it
It takes several hot days to melt the tar into the wood. What you did is correct. You just need to tape all vertical and horizontal sides to get that perfect seal. butyl seam tape as mentioned by gracie13725. Since you over do this is a perfect solve. Go get um Don!
Please don't lose heart at a setback. There are likely more to come. You are so wonderful at keeping everyone entertained, and your work ethics are to be admired. I remember when your appendix burst, we were afraid for your health and your continuing the project. Prayers and best wishes.
Don. I have never seen you so despondent .In fact I have never seen you give us bad news about any part of your build.Don`t let it get you down Don.You are made of stronger stuff than most of us viewers.I have absolutely no doubt that you will pick yourself back up and tackle the problem head on and conquer it.I and no doubt all of us subscribers wish you strength and good luck with the issue.You can and will overcome it.
Yea underlayment is only to keep water off if it rains before installing the actual roofing, once you install the roofing it is basically worthless due to the amount of holes punched in it. But that's what the roofing material is for. Underlayment might leak a bit but it's fine as long as it's allowed to dry out before finishing, he is building new construction so as long as he roofs it he's fine.
I hope your new wood didn't get too wet after all that work but I am sure it will dry out, just finish the roof and keep the building ventilated. On new buildings I prefer to get the roof on even before the walls are covered that way if does rain I can just install some plastic around the outside walls and the inside is more protected. Good luck.
Hey Don! I remember a roof that I worked on installing sort of near you in Safford. This was in the days prior to [my] cell phone use, so I don't have any photos. But it was slightly different. After installing underlayment and then roll roofing, with scutters and so forth to drain off the rain, there was a persistent leak. This was a flat roof with mild to zero slope, and a surrounding parapet wall. I worked on it for what seemed like a cple of weeks. It was built according to the architect's design who was very insistent that things be done his way. Of course, he lived in L.A. and didn't understand Arizona Monsoon weather, nor did he, being a full-blooded Serbian, understand American persistence and willingness to modify the rules of architecture in order to make things work, which on paper might look swell, but in reality were totally dysfunctional. I remember going crazy trying to fix the leak(s). Phone calls to manufactures of exotic drainage systems, parts ordered from here and there, etc. etc. Time - hours and days - spent tearing my hair out. My time working on the project came to an end, as The Lord would have it, and I left that project and living environment (this was St. Paisius Monastery, maybe a 100 miles from where you are located, in the next County over - Graham County) and moved to Memphis. It was several years later that I discovered the architect had been "relieved" of his imposing duties (i.e. stuff he imposed upon me to do) and the roof was entirely rebuilt as a conventionally pitched roof. In other words, unlike your issues which I know you will resolve, and which are not as devastating as you might think, were issues built into an impractical design for the environment in which they were implemented. You are definitely on the right track with your roof, and I can't wait to see where and why there are leaks! I think someone else mentioned that this set-back is actually beneficial at this stage. You can rectify what is a foundational error, before you build upon it and compound the damage, making a fix even more difficult. And I don't see it as an error in your work; I think it's probably something else yet to be discovered. Water can be a mighty foe, but man can harness it and control it, to a large degree, albeit not completely. I'll end this totally overlong comment with one of my favorite verses which is probably completely irrelevant: " The king’s heart is in the hand of the Lord, as are the watercourses; He turns it whichever way He wills." Proverbs 21. God is with you. Even as He brings the rain, He gives you the ingenuity and the practical skills to harness it regarding your home. I have no doubt as to a satisfying ending to this current saga!
Oh no, my dear friend. My heart breaks seeing you down. I'm sitting here bundled up on my couch with the flu, wishing there was something I could do. Sending thoughts and prayers and help.
0:40 I use Harbor Freight Atlas 40 V with Grass Gator tri-blade head. Months on one set of blades. There's a newer competing blade head that has easier to change blades and the Grass Gator blades fit. The peel and stick blue stuff is a backup barrier, not your main rain protection. It's not really meant to stop a rainstorm without shingles or a metal roof above. The galvalume you plan shouldn't leak through to that peel and stick for 20 to 40 years.
Hi Don, I watch an Arkansas homestead channel and they use a walk behind string trimmer. It works on fairly heavy brush. I bought an ergonomic weed eater a few years ago, it was high quality but just using it for 25 minutes made my hands go numb from the vibration so if I had to cut an area as large as yours I would buy a walk behind to avoid nerve damage.
Personally I would have mabe the over lapes wider and at the ridge brought one side one foot over the top Then brought the other side one foot over the ridge... Yes I would use more material... But I like to go over kill I would over lap horizontals at least one foot... But that's just me..
You got this Don, I have complete faith in you! As for the weeds, do you have any neighbors with goats or llamas? They are automatic weed eaters and fertilizer spreaders at the same time! Hang in there man!
So sorry about the roof leaks after all that work. Like a good soldier, you get back to solving the problem. We can all learn from you. You'll get this under control.
Roof didn't leak, underlayment did. One you put on the actual roofing due to the holes the underlayment is basically worthless anyway, just meant to keep water off as much as possible before the roof is fully on.
Sorry for the leaks Don, but good you found them now. Leak area sources can be pretty hard to detect sometimes. I once had a roofer (among others) that absolutely could not find the source area of a leak. But a new roof ended up solving the problems. (I needed a new roof due to hail damage, so that was okay). I think you have been working so hard on your home that you may be more tired than you think. Perhaps that is why you felt so (uncharacteristically) disappointed. Although you are human, my friend , so I understand. I know you will be back at it with a renewed sense of purpose and accomplishment...because that is who you are. We will all be waiting to cheer you on when you return. All the love!🥰🥰
Don’t beat yourself up to bad. I was told Roofs are not waterproof, they are designed to shed water faster than it can seep through. You’re doing great! ❤️ besides, there still another layer to go on.
I have had those plastic cap roofing nails leak before and once I put butyl tape over them, leaks were solved. Cant be sure that is your issue because I cant see the way the underlayment is laying but as long as the underlayment is overlapping like birds' wings overlap to shed water, there shouldn't be leaks.Phooey! I used a butyl tape roller to secure the tape. I will pray about it. I hope the solution is soon apparent. In the missionary field, I use 1 billboard tarp tocover the entire roof and fasten it under the eaves and never have leaks. Then I come home and use " fancy stuff " and have experiences just like this...
You are doing great and those leaks aren't going to cost you a bundle to repair, unlike my gaffs (not GAF] in life. Follow the directions in the comments section. Some really great advice out there. Thanks for an engaging video Don.
Although your hard work ended up with a glitch as I like to call it... I've found in life that with each setback... we somehow come out a little stronger and little wiser. As long as you are still safe and unharmed... it will all be for the better. Veteran Charlie.
Are you going to have a ridge vent of gable end vents? I agree with the butyl tape for seams. You're getting there. There is always a solution. The pros in San Fransisco built a skyscraper that is leaning, so you are not in too bad of a pickle.
From one old timer to another--remember how our setbacks make our successes that much better! Looking forward to your next video. There is a good chance this could be an easy taping fix. Bummer you ran short on material for the ridge area, it looked sooo close!
Part 2 incoming! Yeah that is disappointing, but don't sweat the small stuff, At least is leaked BEFORE the metal roof went on, then there'd be a whole can of worms to work out! lol Godd luck Don!
Re: weed-eaters-I have no experience, having experience with cattle, but I've heard positive things about goats. I am very sad that you had those leaks, and cannot imagine what might have gone wrong, so to speak. I hope you can determine what the cause is, and *_dearly_hope_* that the remedy is easy and quick! ❤️
We got an electric trimmer from EGO. They are expensive, but no gas or pulling my arm out of place! The line is self-feeding and it always comes out to add line. It IS powerful. There are others. Shop around. Maybe someone will gift you one. I would if I could. Carry on.
That must have been a tough moment Don. But you are the man, I'm sure you will get it all sorted and this will just be another story that adds to the character of your new home.
Don, before you go crazy with the weed eater, mark where some of those sunflowers are. I’m pretty sure they are sun chokes , also called Jerusalem Artichokes. Real good healthy super food. You can dig them up all winter as you need them. You should look into them. They could keep you alive in hard times. Might be worth trying some.
Hang on, Don. You have used a really great product. I think the solution is simple, and it seems from reading some other comments, it is the open vertical seams that need sealing. The wind would drive the rain across the roof and under any opening.... even small ones, between the layers of roofing shield. Just use your tape to seal the seams. Please do not let this get you down. I think perhaps you are very tired. Take a breath and give yourself a break. sending a hug and love from the prairies. ❤️❤️❤️
Good man! If at first, you don't succeed, try, try again. Never give up, never give in. One foot after the other (even if baby steps), is moving forward. You will get there. You are doing this! I think you are amazing for all you have accomplished out there. 😀
Don, just watching you tackle that ladder every time you have to move it, then up and down it... reminds of my roofing days! One heck of a workout by the end of the day. Safety always first! Great video and great learning for your viewers. Veteran Charlie.
Look at it this way..Until recently, since the invention of roof shingles, there was no need to install a water-proof underlayment just so you could pound thousands of roofing nails though it. Water-proof roof underlayment isn't a terrible idea, especially as an eave ice guard, but #15 tar paper underlayment was just fine before peel & stick came along.
I have a good analogy for your situation. It's like making a sandwich and carefully placing it in a zip-lock bag. When you took it outside in the rain the sandwich got wet. The job wasn't finished. Zip the bag up. I'm so glad your so close to having the roof done.
Well, that is discouraging and depressing. Having built my own little house and having spent all day working and feeling tired but happy at the end of the day only to find there is some problem that has to be fixed when I thought I did everything right can be overwhelmingly disappointing - especially when you are alone In the end it will be okay. You will fix this and move on because you are that kind of person. We are all here for you. I do think placing two runs along the ridge in the proper place instead of trying to make one piece work may very well fix the leaks.
The leaks can be fixed. Just need seam tape... Are you planning in cutting in roof vent on the roof ridge before you install the roof?? be safe and happy..
Leave the underpayment on …….I would spray a sealant over top and install a metal roof…..which by the way is easy for one person. As far as that goes you don’t even have to do anything further if going with metal. I am 75 and I am able to do it, so can you.
You constantly show us you can do it yourself but there are times when an extra pair of hands would be extremely helpful and speed up the process exponentially. Winter's coming, get that roof done asap!
I’m really sorry for this very discouraging setback, Don. With all the hard work you’ve put into it…😓 I would say the silver lining is that you were given the opportunity to see the leaks sooner rather than later after the entire roof was finished. Sometimes this is the Father’s way to remind us how much He cares about His children, even if it may not seem so. You still amaze us all, Don. Keep on being the awesome person God made you. 🤗
Don't be discouraged! I would bet the issue is the patching work you did, on that top row over the ridge. You have to think like a drop of water, when building a house--so upper courses must always overlap the lower courses. Anytime you patch on top of both an upper and lower course, it leaves the top edge of the patch exposed, which invites water to seep right on in that spot. It may seem odd, but it's not at all uncommon. If it was my house, I'd take off that top course, and instead do two new rows, one on each side of the ridge, with one flapping over the top onto the other. Also, are you doing spray foam insulation in your roof? I'm assuming you are, since you aren't leaving a ridge vent? But just wanted to check and be sure, in case you hadn't thought about it yet. There's so much to keep track of... but you're doing such a quality job, you'll end up with a really well built house.
Hi Cheryl. Spray foam is the focus at this point. Some more research to do but that will probably be my choice. Great suggestions re: Overlap and leak issues. Many thanks for the kind affirming words.
Leaks are a bit of a setback.. but don't be discouraged. This will pass. Do houses in the desert not benefit from using Ridge Venting to reduce heat accumulation ?
I had to watch it twice, but you clearly didn’t tape up the seems between the sheets. Good news is you’re out west, and that wood will dry out and your project will be fine. Watch some more videos, buy some good tape, and get some corrugated steel up there and you’ll be just fine.
that 'roof portal' is just awesome,im not keeping up with you videos very well,maybe youve already said where that idea 'popped up'from...You big house is surely almost 'home !!!! ❤🎉
Hi Don! Really feel for you. Water leakage is my nemesis too. Admiring your honesty and sincerity. I rarely read other people's comments, but I did now. We all have your back and there is a lot of good advice to read there. I moved into a new apartment and was greeted by a water leak on day 2. Big shock. But it worked out.
Just my personal preference.. When I've installed underlayment vertically and horizontally I always lap it at least 6 inchs... 3 inches always gave us (crew) trouble... 6 inches was faster and easuer... But that's just me...
I believe you are supposed to use a roller to insure adhesion... you can probably rent the roller. I would not tear it all off... contact supplier and ask their opinion. Also... did you follow instructions for overlap?
Water will find a way to exploit any weakness. There are forums dedicated to construction, frequented by contractors and people who do this for a living. I'd recommend you find one and post there before you spend any major money or redo your work. You won't have any difficulty finding out where your installation went wrong and your options for fixing it. I enjoy these kinds of videos and contribute when I can, but most people posting on RUclips are amateurs. I hope you can find a professional to help you.
We have a Rigid cordless. Works great! Watch out for rattlesnakes when you’re walking through those bushes I have seen them laying at the bottom of plants. 😊 i’m sorry things didn’t go too well. Hopefully u get it figured.
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
Don, no problem, it's the vertical seams, get some butyl seam tape and you are good to go! ❤ Don't be discouraged bro, you're getting an education!
i wondered about having multiple pieces of underlayment on a single row. i typically see a single piece from end to end. i think you are correct that some seam tape may fix it. i actually think its good Don found them. just seal the seams and wait for the next rain to test it.
@@WaywardOffGrid I think that's the only thing it can be, that underlayment is good stuff and it looks to be laid correctly. Only thing that I don't like is that patchwork seam at the ridge piece but some butyl tape will fix that too. Probably would have done a 1ft piece on both sides so that would make the ridge piece lay atop on both sides. But no worries, it'll be good to go.
Crazy how much seam tape is now, I was shocked when we built our tiny house.
I pray that I'm in Don's shape when I get there, what an inspiration! ~much love
❤
I hope Don is reading the comments BEFORE he takes action. I worry that because of the build up of the videos, he may have already scrapped what he did and tried something completely different. We shall see.
Don, just think. If it didn't rain, you wouldn't have known that there were any leaks once it's all said and done. You have taught me what grit means. I see the disappointment in your face, yet your determination lingers in your eyes. We are not going to give up on you so you shouldn't either. Teach that roof a lesson and we will be in your corner cheering for you the rest of the way.
What a delightful comment. Kind of like a virtual hug. Thanks so much.
Don, we all make mistakes and nothing is perfect. The good thing is it's always fixable. Keep in mind you're doing something most would never attempt. Be proud of what you have done and keep forging ahead. We are all behind you.
Don the peel and stick is a water and ice Shield not even mandatory under metal tar paper would work and would also leak if rained on directly so put the metal on and don't worry about it
Yeah, that's what I was going to say, there isn't even roofing on it yet XD.
The best part is NOW you KNOW exactly where the leaks are.
It takes several hot days to melt the tar into the wood. What you did is correct. You just need to tape all vertical and horizontal sides to get that perfect seal. butyl seam tape as mentioned by gracie13725. Since you over do this is a perfect solve. Go get um Don!
Many thanks for the suggestions.
You'll conquer this like you have everything else
Please don't lose heart at a setback. There are likely more to come. You are so wonderful at keeping everyone entertained, and your work ethics are to be admired. I remember when your appendix burst, we were afraid for your health and your continuing the project. Prayers and best wishes.
Don. I have never seen you so despondent .In fact I have never seen you give us bad news about any part of your build.Don`t let it get you down Don.You are made of stronger stuff than most of us viewers.I have absolutely no doubt that you will pick yourself back up and tackle the problem head on and conquer it.I and no doubt all of us subscribers wish you strength and good luck with the issue.You can and will overcome it.
Keep the head up, Don.... No roof is going to defeat you!
thats just a liner don, put shingles or whatever over it and its all good, it wont leak
Yea underlayment is only to keep water off if it rains before installing the actual roofing, once you install the roofing it is basically worthless due to the amount of holes punched in it. But that's what the roofing material is for.
Underlayment might leak a bit but it's fine as long as it's allowed to dry out before finishing, he is building new construction so as long as he roofs it he's fine.
YES, now you know where the leaks are nails must hit the studs don't forget the roof is still in raw form 90% finished, STAY ENCOURAGED.
Don't be disappointed; you are doing a great job solo. If there's a problem, there is always a solution. Don't worry be happy!
I hope your new wood didn't get too wet after all that work but I am sure it will dry out, just finish the roof and keep the building ventilated.
On new buildings I prefer to get the roof on even before the walls are covered that way if does rain I can just install some plastic around the outside walls and the inside is more protected. Good luck.
Hey Don! I remember a roof that I worked on installing sort of near you in Safford. This was in the days prior to [my] cell phone use, so I don't have any photos. But it was slightly different. After installing underlayment and then roll roofing, with scutters and so forth to drain off the rain, there was a persistent leak. This was a flat roof with mild to zero slope, and a surrounding parapet wall. I worked on it for what seemed like a cple of weeks. It was built according to the architect's design who was very insistent that things be done his way. Of course, he lived in L.A. and didn't understand Arizona Monsoon weather, nor did he, being a full-blooded Serbian, understand American persistence and willingness to modify the rules of architecture in order to make things work, which on paper might look swell, but in reality were totally dysfunctional. I remember going crazy trying to fix the leak(s). Phone calls to manufactures of exotic drainage systems, parts ordered from here and there, etc. etc. Time - hours and days - spent tearing my hair out. My time working on the project came to an end, as The Lord would have it, and I left that project and living environment (this was St. Paisius Monastery, maybe a 100 miles from where you are located, in the next County over - Graham County) and moved to Memphis. It was several years later that I discovered the architect had been "relieved" of his imposing duties (i.e. stuff he imposed upon me to do) and the roof was entirely rebuilt as a conventionally pitched roof. In other words, unlike your issues which I know you will resolve, and which are not as devastating as you might think, were issues built into an impractical design for the environment in which they were implemented. You are definitely on the right track with your roof, and I can't wait to see where and why there are leaks! I think someone else mentioned that this set-back is actually beneficial at this stage. You can rectify what is a foundational error, before you build upon it and compound the damage, making a fix even more difficult. And I don't see it as an error in your work; I think it's probably something else yet to be discovered. Water can be a mighty foe, but man can harness it and control it, to a large degree, albeit not completely. I'll end this totally overlong comment with one of my favorite verses which is probably completely irrelevant: " The king’s heart is in the hand of the Lord, as are the watercourses; He turns it whichever way He wills." Proverbs 21. God is with you. Even as He brings the rain, He gives you the ingenuity and the practical skills to harness it regarding your home. I have no doubt as to a satisfying ending to this current saga!
Tim ol friend this was a great share and I so appreciate your encouragement.
Oh no, my dear friend. My heart breaks seeing you down. I'm sitting here bundled up on my couch with the flu, wishing there was something I could do.
Sending thoughts and prayers and help.
0:40 I use Harbor Freight Atlas 40 V with Grass Gator tri-blade head. Months on one set of blades.
There's a newer competing blade head that has easier to change blades and the Grass Gator blades fit.
The peel and stick blue stuff is a backup barrier, not your main rain protection. It's not really meant to stop a rainstorm without shingles or a metal roof above.
The galvalume you plan shouldn't leak through to that peel and stick for 20 to 40 years.
Zip Board or GP's forcefield are the only way to go Don.I think once you get the roof on it will be fine. We are always the hardest on ourself's
You can do this Don! I know you can figure it out!
You have to do a roof from the bottom up so all overlapping is shedding water downward. Patching seems the reverse of this will spell disaster
Hi Don, I watch an Arkansas homestead channel and they use a walk behind string trimmer. It works on fairly heavy brush. I bought an ergonomic weed eater a few years ago, it was high quality but just using it for 25 minutes made my hands go numb from the vibration so if I had to cut an area as large as yours I would buy a walk behind to avoid nerve damage.
Personally I would have mabe the over lapes wider and at the ridge brought one side one foot over the top
Then brought the other side one foot over the ridge...
Yes I would use more material...
But I like to go over kill
I would over lap horizontals at least one foot...
But that's just me..
Sending you positive vibes
You got this Don, I have complete faith in you! As for the weeds, do you have any neighbors with goats or llamas? They are automatic weed eaters and fertilizer spreaders at the same time! Hang in there man!
So sorry about the roof leaks after all that work. Like a good soldier, you get back to solving the problem. We can all learn from you. You'll get this under control.
Roof didn't leak, underlayment did. One you put on the actual roofing due to the holes the underlayment is basically worthless anyway, just meant to keep water off as much as possible before the roof is fully on.
Sorry for the leaks Don, but good you found them now. Leak area sources can be pretty hard to detect sometimes. I once had a roofer (among others) that absolutely could not find the source area of a leak. But a new roof ended up solving the problems. (I needed a new roof due to hail damage, so that was okay). I think you have been working so hard on your home that you may be more tired than you think. Perhaps that is why you felt so (uncharacteristically) disappointed. Although you are human, my friend , so I understand. I know you will be back at it with a renewed sense of purpose and accomplishment...because that is who you are. We will all be waiting to cheer you on when you return. All the love!🥰🥰
Don’t beat yourself up to bad. I was told Roofs are not waterproof, they are designed to shed water faster than it can seep through. You’re doing great! ❤️ besides, there still another layer to go on.
Will you get a roofer?! Oh you better post soon, Im at the edge of my seat...waiting for the next video!!!!😅❤🙋🚗🇨🇦‼️
I have had those plastic cap roofing nails leak before and once I put butyl tape over them, leaks were solved. Cant be sure that is your issue because I cant see the way the underlayment is laying but as long as the underlayment is overlapping like birds' wings overlap to shed water, there shouldn't be leaks.Phooey! I used a butyl tape roller to secure the tape. I will pray about it. I hope the solution is soon apparent. In the missionary field, I use 1 billboard tarp tocover the entire roof and fasten it under the eaves and never have leaks. Then I come home and use " fancy stuff " and have experiences just like this...
The disappointment was so evident. Sending positive thoughts your way. I admire what you're doing, it's inspirational!
You are doing great and those leaks aren't going to cost you a bundle to repair, unlike my gaffs (not GAF] in life. Follow the directions in the comments section. Some really great advice out there. Thanks for an engaging video Don.
Although your hard work ended up with a glitch as I like to call it... I've found in life that with each setback... we somehow come out a little stronger and little wiser. As long as you are still safe and unharmed... it will all be for the better. Veteran Charlie.
Are you going to have a ridge vent of gable end vents? I agree with the butyl tape for seams. You're getting there. There
is always a solution. The pros in San Fransisco built a skyscraper that is leaning, so you are not in too bad of a pickle.
Probably too late but here it is code to have two layers at the eves (bottom). This is actually a good thing in the long run. Best of luck.
You always seem to have the right remedy for your problems Don. Step back and solve it 👍
My heart breaks for you but you can’t give up❤
Good morning Don I see that you a very hard worker be good to your self and be careful
Cheer up Don you got this. 💪😁👍You're a intelligent man.
From one old timer to another--remember how our setbacks make our successes that much better! Looking forward to your next video. There is a good chance this could be an easy taping fix. Bummer you ran short on material for the ridge area, it looked sooo close!
Put some firing strips down a put a metal roof on
Part 2 incoming! Yeah that is disappointing, but don't sweat the small stuff, At least is leaked BEFORE the metal roof went on, then there'd be a whole can of worms to work out! lol Godd luck Don!
You are doing good man. Keep it up ❤ We never stop learning
Re: weed-eaters-I have no experience, having experience with cattle, but I've heard positive things about goats.
I am very sad that you had those leaks, and cannot imagine what might have gone wrong, so to speak. I hope you can determine what the cause is, and *_dearly_hope_* that the remedy is easy and quick! ❤️
You got this, relax and enjoy your good Job!
We got an electric trimmer from EGO. They are expensive, but no gas or pulling my arm out of place! The line is self-feeding and it always comes out to add line. It IS powerful. There are others. Shop around. Maybe someone will gift you one. I would if I could. Carry on.
That must have been a tough moment Don. But you are the man, I'm sure you will get it all sorted and this will just be another story that adds to the character of your new home.
Don, before you go crazy with the weed eater, mark where some of those sunflowers are. I’m pretty sure they are sun chokes , also called Jerusalem Artichokes. Real good healthy super food. You can dig them up all winter as you need them. You should look into them. They could keep you alive in hard times. Might be worth trying some.
Hang on, Don. You have used a really great product. I think the solution is simple, and it seems from reading some other comments, it is the open vertical seams that need sealing. The wind would drive the rain across the roof and under any opening.... even small ones, between the layers of roofing shield. Just use your tape to seal the seams. Please do not let this get you down. I think perhaps you are very tired. Take a breath and give yourself a break. sending a hug and love from the prairies. ❤️❤️❤️
I have faith you will figure it out!
Good man! If at first, you don't succeed, try, try again. Never give up, never give in. One foot after the other (even if baby steps), is moving forward. You will get there. You are doing this! I think you are amazing for all you have accomplished out there. 😀
Don't worry about it, we all have trails, you have done a great job so far! If it was to easy we would all be out there doing what your doing!
It will be good you are the man
Don. Leaving us with a cliff hangar!!! Hope this gets resolved easily Looked Great to me. Hang in there buddy!!!
Chin up Don!!! We all have set back on projects!!! Don't give up it's a learning curve!!! If this is the only one you've done great!
I use a Ryobi cordless weed trimmer, love the cordless mobility, without the noise of a gas powered unit.
Don, just watching you tackle that ladder every time you have to move it, then up and down it... reminds of my roofing days! One heck of a workout by the end of the day. Safety always first! Great video and great learning for your viewers. Veteran Charlie.
You got this !! I know you Will do it .😊
Don you will research the problem and solve it like you've done before. Keep at it. It will be awesome.
aw gee. we're all behind you! better to find out now than later.
Look at it this way..Until recently, since the invention of roof shingles, there was no need to install a water-proof underlayment just so you could pound thousands of roofing nails though it. Water-proof roof underlayment isn't a terrible idea, especially as an eave ice guard, but #15 tar paper underlayment was just fine before peel & stick came along.
I have a good analogy for your situation. It's like making a sandwich and carefully placing it in a zip-lock bag. When you took it outside in the rain the sandwich got wet. The job wasn't finished. Zip the bag up. I'm so glad your so close to having the roof done.
Just a second layer on.
Stager the joints.
Maybe cut a roll In half. So first one is only 18 inchs wide...
Well, that is discouraging and depressing. Having built my own little house and having spent all day working and feeling tired but happy at the end of the day only to find there is some problem that has to be fixed when I thought I did everything right can be overwhelmingly disappointing - especially when you are alone In the end it will be okay. You will fix this and move on because you are that kind of person. We are all here for you.
I do think placing two runs along the ridge in the proper place instead of trying to make one piece work may very well fix the leaks.
Stay tuned same time same channel. We'll that's a bummer. So what will you do next? Hire a roofing company.? Can't wait for next video!
Praying for you, Don! You are doing a good job so don't be discouraged.
I use husqvarna brush cutter. Gas powered. Best of the best. Got mine at tractor supply in sierra vista. $270.
once you put the tin on the roof.
HEY PRESTO.
No more leaks
Thanks!
Many thanks for the kind gift.
Well that sucks Don..but you'll figure it ! Keep your chin up 😁👍
The leaks can be fixed. Just need seam tape... Are you planning in cutting in roof vent on the roof ridge before you install the roof?? be safe and happy..
Leave the underpayment on …….I would spray a sealant over top and install a metal roof…..which by the way is easy for one person. As far as that goes you don’t even have to do anything further if going with metal. I am 75 and I am able to do it, so can you.
There’s always a solution there Don! Reach out if you need to chat!
WoW....... and it looked so good when you got done.
Let your roof dry out good before you tape it, steam will get trapped and make a leak!
You constantly show us you can do it yourself but there are times when an extra pair of hands would be extremely helpful and speed up the process exponentially. Winter's coming, get that roof done asap!
I’m really sorry for this very discouraging setback, Don. With all the hard work you’ve put into it…😓
I would say the silver lining is that you were given the opportunity to see the leaks sooner rather than later after the entire roof was finished. Sometimes this is the Father’s way to remind us how much He cares about His children, even if it may not seem so.
You still amaze us all, Don. Keep on being the awesome person God made you. 🤗
Thanks for those words of wisdom Helene. So appreciate all of the kind cheering me on with this one.
It's leaking on the ridge put more material on the ridge anti working with roofing no matter what material it is 6 in lap over is a rule of thumb
No rain in my area 30 some miles away from you. I watched all the rain go right around us to you all summer. I use only Stihl equipment.
BTW... I love my M18 Trimmer by Milwaukee...
Not to be dismissive of what happened. But it's good you found out so fast and not after all the metal roof was in place.
Yes I can see the silver lining in this cloud for sure.
Don't be discouraged! I would bet the issue is the patching work you did, on that top row over the ridge. You have to think like a drop of water, when building a house--so upper courses must always overlap the lower courses. Anytime you patch on top of both an upper and lower course, it leaves the top edge of the patch exposed, which invites water to seep right on in that spot. It may seem odd, but it's not at all uncommon.
If it was my house, I'd take off that top course, and instead do two new rows, one on each side of the ridge, with one flapping over the top onto the other.
Also, are you doing spray foam insulation in your roof? I'm assuming you are, since you aren't leaving a ridge vent? But just wanted to check and be sure, in case you hadn't thought about it yet. There's so much to keep track of... but you're doing such a quality job, you'll end up with a really well built house.
Hi Cheryl. Spray foam is the focus at this point. Some more research to do but that will probably be my choice. Great suggestions re: Overlap and leak issues. Many thanks for the kind affirming words.
Leaks are a bit of a setback.. but don't be discouraged. This will pass. Do houses in the desert not benefit from using Ridge Venting to reduce heat accumulation ?
I had to watch it twice, but you clearly didn’t tape up the seems between the sheets. Good news is you’re out west, and that wood will dry out and your project will be fine. Watch some more videos, buy some good tape, and get some corrugated steel up there and you’ll be just fine.
Go over your last run you can't patch overlap split sheet then run full over top.
It really looked as though it was a great job being laid down. What could’ve been the reason it leaked so much? I’m sorry for this set back. 🙏
In a way, it was good to find any leaks before you added the finish roof layer.
Now that was dramatic! Seriously, I've had those moments along the way myself except I cry like a baby.
Thanks Jory. Real men cry rather than bottle it up and end up mentally ill or troubled further.
that 'roof portal' is just awesome,im not keeping up with you videos very well,maybe youve already said where that idea 'popped up'from...You big house is surely almost 'home !!!! ❤🎉
I use a DR wheeled brush cutter. It's over 20 years old and still working great! Very easy to manuever also.
Butyl tape on the seams@ Boom you are now leak proof especially after installing your metal roofing
Hi Don! Really feel for you. Water leakage is my nemesis too. Admiring your honesty and sincerity. I rarely read other people's comments, but I did now. We all have your back and there is a lot of good advice to read there. I moved into a new apartment and was greeted by a water leak on day 2. Big shock. But it worked out.
Just my personal preference..
When I've installed underlayment vertically and horizontally
I always lap it at least 6 inchs...
3 inches always gave us (crew) trouble... 6 inches was faster and easuer...
But that's just me...
Super nice work buddy, Tin or shingling?
This is only the underlayment easy enough to fix before you put the roofing on .
Don’t worry, it only rains twice a year where you’re at
I believe you are supposed to use a roller to insure adhesion... you can probably rent the roller. I would not tear it all off... contact supplier and ask their opinion. Also... did you follow instructions for overlap?
Water will find a way to exploit any weakness. There are forums dedicated to construction, frequented by contractors and people who do this for a living. I'd recommend you find one and post there before you spend any major money or redo your work. You won't have any difficulty finding out where your installation went wrong and your options for fixing it. I enjoy these kinds of videos and contribute when I can, but most people posting on RUclips are amateurs. I hope you can find a professional to help you.
We have a Rigid cordless. Works great! Watch out for rattlesnakes when you’re walking through those bushes I have seen them laying at the bottom of plants. 😊 i’m sorry things didn’t go too well. Hopefully u get it figured.
This off grid life. The fellow on that site was a roofer. Contact him for advice, I'm sure he will assist you
Hang in there, donny.