Thank you again, Christian! As always you're a life saver! Have re-done the lab 3 times and had some questions, when you simply informed that there was no possibility to set the "pass min length" and "login block-for" commands for the SW in the PT :) At the same time I still have some questions regarding the vty lines: 1. As per the 1st reflection question you said that: the originally set vty password was disabled once the "login local" command was issued, is this correct? So after configuring username/secret all previously configured vty lines passwords shall be irrelevant? (even if the "sh run" command indicates the vty passwords) 2. I have attempted to configure the vty lines with a separate password (i.e. vty 0 14 - pass X, vty 15 - pass Y), but was unable to telnet remotely and login with pass Y. Thus, is there a possibility to use a specific password per specific vty line? 3. What is the difference of creating ssh on the vty lines and configuring simply the "login" command vs "login local"? Thank you again and wishing you all the best!!!
yes, thank you, packet tracer does not support min length passwords and login block commands. 1. Yes, login local command will replace login command, so the password in vty will be ignored and password with local username will be used. 2. if you configure 0-14 with password X , you need 15 telnet connections with password X, and finally the 16th connection will use password Y. 3. login command enable the telnet password configured in vty lines, and login local will use the username name and password previously configured Thank you
@@romeroc24 Thank you again for the prompt and extensive clarification, Christian! Now you've cleared all my previous doubts. ;) All the best and Happy upcoming Holidays!!! :)
Hello Christian, After 15:57 (crypto key.....) I went to other room. When I came back it wants password. Like this: Unauthorized Access is Prohibited! User Access Verification Password: I wrote all of password on the Lab, it didn't accept any of them. What is the password? Thank you in advance.
If it weren't for your videos I probably wouldn't have passed Networking
thank you for all your support
How can I identify the vty, like when it is line vty 0 15 and when it is line vty 0 4 etc.
From 0 to 15 you have 16 possible connections, from 0 to 4 only 5
Thank you again, Christian!
As always you're a life saver! Have re-done the lab 3 times and had some questions, when you simply informed that there was no possibility to set the "pass min length" and "login block-for" commands for the SW in the PT :)
At the same time I still have some questions regarding the vty lines:
1. As per the 1st reflection question you said that: the originally set vty password was disabled once the "login local" command was issued, is this correct? So after configuring username/secret all previously configured vty lines passwords shall be irrelevant? (even if the "sh run" command indicates the vty passwords)
2. I have attempted to configure the vty lines with a separate password (i.e. vty 0 14 - pass X, vty 15 - pass Y), but was unable to telnet remotely and login with pass Y. Thus, is there a possibility to use a specific password per specific vty line?
3. What is the difference of creating ssh on the vty lines and configuring simply the "login" command vs "login local"?
Thank you again and wishing you all the best!!!
yes, thank you, packet tracer does not support min length passwords and login block commands.
1. Yes, login local command will replace login command, so the password in vty will be ignored and password with local username will be used.
2. if you configure 0-14 with password X , you need 15 telnet connections with password X, and finally the 16th connection will use password Y.
3. login command enable the telnet password configured in vty lines, and login local will use the username name and password previously configured
Thank you
@@romeroc24 Thank you again for the prompt and extensive clarification, Christian! Now you've cleared all my previous doubts. ;) All the best and Happy upcoming Holidays!!! :)
@@damasta.md.99 Thank you, thank you
very useful thank you sir.
Thank you for all your support my friend!!!
On-Time 11:36 You got back to the Terminal and were able to do conf Term but for me, I Cant its showing as R1> instead of # what did I do wrong?
when you have R1>, use enable to go R1# and use conf term to go R1(config)#
@@romeroc24
Thank you. Now it’s asking for a password would it be Cisco?
I put that Cisco and it said it was wrong
@@mariepierre4216 please restart the activity because maybe you forgot the password
@@mariepierre4216 restart
Thanks for you tutorials
Glad you like them!
Hello Christian, After 15:57 (crypto key.....) I went to other room. When I came back it wants password. Like this:
Unauthorized Access is Prohibited!
User Access Verification
Password:
I wrote all of password on the Lab, it didn't accept any of them. What is the password?
Thank you in advance.
That is the console password, maybe you configured a password that you don't remember, please try the activity again
DId u skip the login commands at. 34:16?
Yes I missed login on console and login on vty, later in the lab you will add login local command on vty
can we request videos
have a packet tracer i cant do
yes, use social media shown 00:03
love the vids thanks for the help !
Glad you like them! Thank you
Thank you again
thank you very much
so useful. thanks a lot!!!!!!
Glad it was helpful!
Thank you very much
I appreciate
Thank you
thanks to you
Bro I need help for one such task, can u help?
yes not problem, contact me using social media shown in 00:03
@@romeroc24 thank you
Hey christian can you email the PKA file pleaseee!
PLease follow all steps in this short video
@@romeroc24 but I have an error in configuring PC-A to Switch why?
R1>enable Password: Password: Password: % Bad secrets just like this !
I can't configure terminal again? why please?
How did you solve this?
u saved a bitch's life
Nice!
Hazlos más faciles please
OK, mejoraré los videos
هلو خواجه كيف حالكو
شكرا لك جيد جدا