Terbaik lahh terjumpa video tuan ni.. uncle pun tengah pikir cara buat utk table saw bossman uncle.. serupa dgn model stanley ni.. terima kasih tuan atas perkongsian idea ni 😍👍👍👍
this vid is superb, i would like to know the measurement of the insert(the frame you created) and also what is supporting the whole saw because it is heavy.
Hello, regards from Colombia, I liked your idea, recently I bought a table saw (Stanley) and I would like build a workbench like yours, could you say me what was thickness of plywood you used?
@@MrAppleorange90 So enhanced it not improved. Is there anything that make you think you should've bought a different brand? like straight cut, 90degree angle. cutting height?
Hi I have a same table saw as yours, lately I found that the the saw blade at maximum height is not 90 degree to the table face although I tilt it to 90 degree. In a result that I have off cut of 1 mm between the lowest and maximum height. Do you have any idea how to fine tune it?
@@MrAppleorange90 tq reply ye bang..pemukaan ape tu bang? 1.Table steele straight 2.blade baru. Abang pernah tak potong board 4x8ft dengan setup abang ni? Potong 8ft panjang straight.. if pernah bang. Abg sorang potong?abg feed je board tu? Board tu brapa mm tebal? Tak lompat bang board tu? Tak pun setup abg ni paling panjang kayu brapa ft/cm potong?. Banyak tanye pulak hehe nak ikut bang setup abg ni.
@@abdulabdul6635 pernah potong plywood 12mm sorang2. setup macam sy buat ni memang sesuai.frame dah berat.lepas tu kita beratkan lagi dengan letak macam2 benda berat dekat bawah.kena stabil baru selamat
@@MrAppleorange90 wow 12mm tebal, berapa panjang bang? Owh mesti tambah berat lagi. Saya pakai setup ori dia potong dalam 76cm panjang 2cm tebal pandai gerak juga bang sudah potong tengah tengah 76cm tu.tapi gerak dia sikit je.pastu sdh pemotongan tak keras tak gerak lagi table tu.
Terbaik lahh terjumpa video tuan ni.. uncle pun tengah pikir cara buat utk table saw bossman uncle.. serupa dgn model stanley ni.. terima kasih tuan atas perkongsian idea ni 😍👍👍👍
good idea thanks very much for the video. I might try it myself if I can find a cheap saw. Your home made fence video was a great job too..
this vid is superb, i would like to know the measurement of the insert(the frame you created) and also what is supporting the whole saw because it is heavy.
bijak bang..simple jer..gantung tu tablesaw tu..x perlu buat base kt bawah
betul..ni pun hasil tiru thaicarpenter buat macam ni.kalau x buat base mcm org lain jugak.susah nak levelkan kalau buat mcm tu
تسلم ايدك good job 👍👍
good work..how to use the Vince with this table?\
Top demais véi bom trabalho irmão 🤝
Hello, regards from Colombia, I liked your idea, recently I bought a table saw (Stanley) and I would like build a workbench like yours, could you say me what was thickness of plywood you used?
hi..im using about 35mm chipboard and its still bow. need to add wood underneath to make it stronger
great work! what thickness the table board?
thickness around 30mm i believe
Was Indy 500 taking place while filming this video?
I think it was the Malibu Grand Prix.
Salfok sama backsongnya 😆
where is the part 2 of this
Can it cut 4x4 wood?
So what was the problem that you tried to improve? was it not working as expected?
size, the fence
@@MrAppleorange90 So enhanced it not improved. Is there anything that make you think you should've bought a different brand? like straight cut, 90degree angle. cutting height?
You should bring it more close to the front make the settings wheels more easy to handle
yup it will be more ergonomic that way
Hi I have a same table saw as yours, lately I found that the the saw blade at maximum height is not 90 degree to the table face although I tilt it to 90 degree. In a result that I have off cut of 1 mm between the lowest and maximum height. Do you have any idea how to fine tune it?
in my table saw, the top table is not flat. the mechanical part for blade also not square. its not a good table saw then i sell it
@@MrAppleorange90 thanks. Sell it out could be one of solution 😂
nanti nak tengok kat belakang opis kot2 ada meja kerani yang rosak tu.. ada guna jugak
haha..boleh guna bang.smooth gila
Bang tutorialnya sekalian dikasih dimensi dong. Trims
Boss, jointer tu boss guna model apa, brapa rm? OK tak. tqvm
einhell 8inci 2in1 jointer dan thickness planer..beli dulu rm1600
@@MrAppleorange90 tahan tak. ada org kata tak begitu baik dia punya jointer. sy dok aim yg jenama jet
@@gerekbasikal1 x rekemen..haha
Helo, what is the overall top table size
the top size is 30inch x 60inch
Mas itu pakai plywood berapa mm?
25mm
Mas untuk ketahanan hardboard gmn untuk top tablesaw?
Hi..table saw ni ada servicing or maintenance ke? Saya potong papan tinggi 1.9cm tapi blade mesti 2.5cm tinggi.itu normal ke bang?
mesin ni kualiti kurang sikit.boleh jadi permukaan atasnya dah melengkung tu tuan.cuba cek tengok
@@MrAppleorange90 tq reply ye bang..pemukaan ape tu bang? 1.Table steele straight 2.blade baru. Abang pernah tak potong board 4x8ft dengan setup abang ni? Potong 8ft panjang straight.. if pernah bang. Abg sorang potong?abg feed je board tu? Board tu brapa mm tebal? Tak lompat bang board tu? Tak pun setup abg ni paling panjang kayu brapa ft/cm potong?. Banyak tanye pulak hehe nak ikut bang setup abg ni.
@@abdulabdul6635 pernah potong plywood 12mm sorang2. setup macam sy buat ni memang sesuai.frame dah berat.lepas tu kita beratkan lagi dengan letak macam2 benda berat dekat bawah.kena stabil baru selamat
@@MrAppleorange90 wow 12mm tebal, berapa panjang bang? Owh mesti tambah berat lagi. Saya pakai setup ori dia potong dalam 76cm panjang 2cm tebal pandai gerak juga bang sudah potong tengah tengah 76cm tu.tapi gerak dia sikit je.pastu sdh pemotongan tak keras tak gerak lagi table tu.
I feel attacked , it isn’t cheap in my country lol! It turned out good anyway
He bought it used, that's why its cheap. New unit still expensive here