A quicker easier Stealth Shelf.
HTML-код
- Опубликовано: 26 сен 2024
- I showed you how to make a stealth shelf before but that one was kind of a pain in the a$$. Here is a quicker simpler way to make one. I used a different lock on this one too.
Slow open air spring : amzn.to/3E43j0q
Motion Sensing Light : amzn.to/3m1rGG5
Hinges : amzn.to/3FnwFrE
RFID Lock : amzn.to/3JwhwHQ
Magnetic Locks: amzn.to/3b37AVm
Foam : amzn.to/32Ua1cJ
I found the foam on Ebay under the description
Customizable Polyethylene Foam Pads for packing and crafts, 1.5 in
Mans said fuck it, I'ma put a shoe box on my wall and hope no one assumes a firearm is in it 😂😂😭
🤫🤫🤫🤫😂
That's some funny shit 😂😂😂
Luv it! Thanks for sharing. Although, I hate locks that click and beep when opening
Hmm I wonder if there are silent ones? I know there are magnetic ones.
That's kick ass I like it
Thank you
This is so nice. The only part messing me up is how’d you know the spacing for the reader.
There's a template that came with it and then a bunch of trial and error.
Buen trabajo, como se llama ese tipo de cerradura?
Right to the point. Good stuff
Thank you
Saw this video 🎉 subscribe🎉 great job two thumbs up
Thank you, thank you
What type of wood did you start off with and measurements ?🤔
It's pine with a dark Walnut stain. I'm pretty sue the top measured 18" long x 10" wide plus the pieces around the edge. Sides of the bottom are 1x4 measured to fit inside the top with an 1/8" gap all around except the back.
I like the build. Did you show how to hang it or did I miss it?
I guess I didn't. If you watch the end you can see two screws on either side of the light that go through the back piece.
❤
😎
Where did you get the lock from? Do you have a link?
Just added one to the description.
amzn.to/3JwhwHQ
How much for one of these
I'm not really selling them anymore.
Are you using the Ryobi brad nailer or pin nailer? Which one do you recommend?
This is the Brad nailer. I would actually recommend no nails for this project, but I am very impatient so I used them instead of clamping.
Thanks for the info. I would rather build them faster too. Plus it would give more peace of mind that they won't come apart.
@@1991DesertVet yeah it's always nice to have that little bit of backup
Yep. I'm planning on going to Home Depot to buy one today. Gotta try out my new table saw now too.
@@1991DesertVet nice. Good luck
What’s the point of the groove made at 2:20?
You have to knock that corner off so it will close properly. Yeah I didn't do a good job showing that.
@@LastLeafStudioVideo oh okay got it. That top piece is 18x12 right? Nice build.
@@SLickev92 I believe it's only 9 1/4 x 18 but I can't remember. I'm sure 12x18 would be just as good if not better
@@LastLeafStudioVideo ok cool . 9 and a quarter sounds better cause I’m trying to keep it more compact .
where can i get the open and close mechanism?
Link in description I think
what hinges did you use ?
@@keithmotley2268 110 degree full overlay hinge
Quicker amd easier than what/which one?
This one
ruclips.net/video/yRoQkLZ_Jq0/видео.html
7:37
What is it?
Quicker!? Easier!?
Yea when you fast forward the video,it's quicker!
Click bait like a mofo
I think it's a lot quicker and easier than the one with crown molding and magnetic lock.