I was looking for a video how to program the Esc with the remote control, because I did not want to buy a program card for 2 settings I need, so I could program my ESC Flycolor 30A in my electric glider, the Beep tones I had not well understood in the instructions, through your video it was then quite simple, even if I did not understand every word of your dialect, but at least the sense of programming, thank you for your video and have fun with your hobby. Excuse my simple English, because I use a translator, this is faster, greetings from Bernhard from Germany
please forgive me if someone has already mentioned this ....but the ShenZhen brand FlyColor is famously popular for producing Drone ESCs, namely their FlyDragon , Francy, Raptor & X-Cross; and also their Lightning Series RC Car ESCs which I have verified do not work with this method... I do appreciate ANYONE that takes their time to post instructional videos especially as well produced as yours. Maybe take the word ALL out of the title though and replace it with ""H2O" or "Boat" ESC"". Again , thank you for your taking time to produce such great quality videoas and know I am just getting into boats and you completely made my mind up to use FlyColor ESCs in my second boat!!! I got a entry level boat that i converted to brushless (very difficult since everything is glued together and so hard as nails to tear into!!! lol😅 What intermediate boat would you recommend on maybe not a shoestring budget more like a 2 shoestring budget! Would you recommend or pass on a used boat? Thank you again, even though i was watching to try on FlyColor Lightning I ended up watching the whole video getting excited for a new boat!!!!!!!😊
I noticed your flying escs, and since you're using them, I grabbed a couple of 150. Going for torque with moderate run.30, 35 ish. For the hooligan feeling I use the gaser. It rocks. I had good speeds and also lots of smoke😁😁😁
Thank you for this video IronClad! Very helpful in setting up our BJ 24 with the Lepord 3660 motor. Just did some testing and had 2 questions. What will cause the ESC / Motor to cut out on a full trigger pass? Once you go back to neutral and apply trigger again it was back on. Secondly...it went into low battery protection mode but I still had 10.8 volts left in the battery. The ESC is set to 3.4 volts on the battery protection mode. Thank you bud!
More than likely it's your prop the prop may be too big for your setup go down and prop size see if it's still power cuts if it's still power cuts the KV of your motor may be too high
thanks dude. The engrish instructions do not make it clear to hold full throttle down all the way to your selection. Also note: maybe its my remote, but neutral wasnt enough, i had to puch pistol throttle full reverse to be acknowedged by ESC.
Hey big B got a questions about new flycolor 90 I put in a bj24. First two runs were flawless. 3rd run, I plug battery in and try to throttle up, motor doesn’t make any revolutions, it just jitters back and forth and instantly heats up to 165° within seconds. Motor wires from esc get hot. Esc arms fine, but won’t turn motor. I replaced the esc with stock one and motor works fine. Have you seen this problem with any flycolor? Defective maybe?
Probably single phasing, Check the esc/motor connectors peel off the heat shrink on the esc/motor wires. You more than likely desoldered a bullet. If that's the case, re-solder the bullet. Also, consider upgrading the connector size to a larger bullet
I’m running 2 3660 2070KV outboard with 2 fly color 90amp, they came with 35mm props I bought 38mm props with a counter rotating prop how do I program my esc
My brandnew Proboat Recoil 2 Shreddy broke my esc (hobbywing 100amp 3s-4s esc.. after 1 minute it stopped only my steering was working but no throttle. So i orderd the Flycolor 150amp esc. I hope this will hold longer on 4s
@@IRONCLADRC why not, because the specs says "2s - 6s" I wont run 6s only 3s or 4s then it should not be a problem isnt it? I have allot of Rc cars running a stock 3s or 4s motor with an 150a or higher esc on it just to have over kill on amps. Why couldnt this work on a boat? (Honost question)
@@IRONCLADRC why not, because the specs says "2s - 6s" I wont run 6s only 3s or 4s then it should not be a problem isnt it? I have allot of Rc cars running a stock 3s or 4s motor with an 150a or higher esc on it just to have over kill on amps. Why couldnt this work on a boat? (Honost question)
Hi Big B,, that's a really informative video, now comes the question,, this stuff is all new to me, my Boat can run on 4s and 6s obviously with the smaller prop for 6s I bought the boat second hand and its set to run forward and backwards which has helped on the rare occasion I've got in a tight spot, so should I alter the settings each time I want to use 4/6s batteries, it came with the 4s prop on. I had to buy the 6s prop, so I'm assuming it's setup for 7-4v, I've run it on 6s once not knowing about these adjustments, will it have come to any harm? I've just downloaded the instruction part of the manual for these settings, Your thoughts would be appreciated bro (Joysway Alpha)
No the settings should be OK switching from 4s to 6s. Unless your tinkering with timing. On 6s I'd be careful with high timing or to low of timing. Always watch your temps
@@IRONCLADRC thanks for the reply, having now just looked at the factory settings diagram it's preset to forward and backwards, and auto battery detection and preset timing, Learning all the time bro thank you for your videos I love them, And a big congratulations to the addition to your family, 🇬🇧
What would cause my boat to get up to full speed 5 seconds is all i get....shuts down ... 5 sec later it will fire up and just repeats it again. Bringing it back at 25% throttle andnits ok.?
You're an animal with rc dude. Hey question, is opting for "forward only" a preference or is not advisable on fast electrics? I understand race rules etc. I guess once you understand your boat and how it slows down you wont need reverse. Guessing here. 🤔
Подскажите пожалуйста, как ESC узнает максимальный ток моего двигателя? Я имею - двигатель 50v max 40A max, 70KV. -Батарея 36v(32-41в), BMS 40A cutoff, - FLYCOLOR FLYDRAGON ESC 12S 80A-V2. Использую двигатель на SUP. Как запрограммировать ESC ток потребления батареи не выше 40A?
Hello. I am going to build a robotic boat using a Flycolor 150A ESC, controlled by Arduino. Can I somehow do a similar calibration with Arduino, or a program card is needed?
Man I've gave you about 200 views on this video last couple days. I've been doing same thing as you but it runs the motor full throttle in the neutral position and throttle stops when I pull the trigger..I've tried the reverse switch on transmitter but same thing..almost starting to wonder if the transmitter came with the trigger wired backwards...have you ever seen that before. It's just a cheap flysky remote picked up on Amazon. You got any ideas what I'm doing wrong?
Been looking at these online for my bj24 cant find very many reviews on them how do you like them? Also everything ive read about the stock prop size and pitch for the bj24 is all over the place and the measurements in the manual are not what the prop on boat measures any idea what the actual pitch and size is?
As for upgraded props for the blackjack 24 I'd definitely go with a tfl 438 or ose 438 size prop it's my go to prop. 440 is also a good one for the boat
Thanks for the quick reply, sweet sounds like ill be ordering a flycolor 90 soon and a surpass hobby 3250kv haha the 440 and 438 props from ose are outta stock but i got a cnc prop comin with same specs as the m440 and a cnc prop with the same specs as the octura x438 we will see how she does!
Necesitó tu ayuda, tengo la Flycolor 90A , tengo la tarjeta configuradora, la he configurado bien , pero en todos los casos me funciona de esta forma, el gatillo de la emisora en reposo (0%) el motor se pone al 100% y para pararlo tengo que presionar el gatillo al 100% , pero el problema es que con esa configuración si suelto el gatillo o pierdo la señal el barco se perderá
My motor makes a continuous beeping sound when I use a maytech remote and try to calibrate esc. Remote is paired and powers motor but unable to calibrate or enter programming mode.
@@IRONCLADRC it's a fairly basic remote with only throttle and brake. No way to modify or set dual rate. Motor doesn't engage till 54% throttle and remotes pwm range is 1-2ms. I'm assuming the esc starts at 1.5ms and can't be changed?
I have a question, my 150a esc had throttle position warning. So if you turn your transmitter on with throttle on, instead of entering program mode, it just sits on constant beeping throttle on warning. Is there a way around the warning to get into programming mode? Thanks!
I'm fairly positive the start up beep beep beep beep beep than a musical tone is called soft start up. 2 of my boats do that with fly color and the other flycolor does not? Hope this helps if not shoot another comment
@@IRONCLADRC Unfortunately no, my start up beeping is constant and does not stop. The manual says that constant beeping on start up means the throttle lever is not in neutral position, but you have to have it at full throttle to enter program mode. I'm wondering if I may have to re-calibrate the throttle position...
I fumbled my way through programming the flycolour 150a in my son’s Spartan. If the transmitter gets out of range of turned off while the boat batteries are hooked up. Is there a way to fix that ? We ran the boat out of range and it kept turning the prop at a reduced rpm.
Hi I’m new at this I just got one of those ESC 70A for one of my boats but when I connected all I get is a constant beeping I haven’t been able to pass that point, all I get is a constant beeping and the motor shakes left and right. Any idea what it could be and what am I doing wrong. Thank you. 👍👍
Super informative, I'm not one to spend more on a program card if I can adjust without. Thanks!
Thank you so much.... it is so informative ... now i can use my flycolor forward and reverse without any programming card
I was looking for a video how to program the Esc with the remote control, because I did not want to buy a program card for 2 settings I need, so I could program my ESC Flycolor 30A in my electric glider, the Beep tones I had not well understood in the instructions, through your video it was then quite simple, even if I did not understand every word of your dialect, but at least the sense of programming, thank you for your video and have fun with your hobby. Excuse my simple English, because I use a translator, this is faster, greetings from Bernhard from Germany
OUTSTANDING INFO BRO THANKS!!!!😎😎👍👍🙏🙏🚤🚤
please forgive me if someone has already mentioned this ....but the ShenZhen brand FlyColor is famously popular for producing Drone ESCs, namely their
FlyDragon , Francy, Raptor & X-Cross; and also their Lightning Series RC Car ESCs which I have verified do not work with this method...
I do appreciate ANYONE that takes their time to post instructional videos especially as well produced as yours. Maybe take the word ALL out of the title though and replace it with ""H2O" or "Boat" ESC"". Again , thank you for your taking time to produce such great quality videoas and know I am just getting into boats and you completely made my mind up to use FlyColor ESCs in my second boat!!!
I got a entry level boat that i converted to brushless (very difficult since everything is glued together and so hard as nails to tear into!!! lol😅 What intermediate boat would you recommend on maybe not a shoestring budget more like a 2 shoestring budget! Would you recommend or pass on a used boat?
Thank you again, even though i was watching to try on FlyColor Lightning I ended up watching the whole video getting excited for a new boat!!!!!!!😊
The udi arrow is a good beginner boats as well as the recoil 2
Your videos are amazing and helpful. Greetings from Finland!
Thanks brother glad I can help. 🇺🇸
I can't recommend the Flycolor programming card enough. You can have It programmed in under a minute ;) Well worth what you pay for it.
Didn't even know they made a program card for the flycolor lol. Thanks bud
I agree the card is the best way. But be warned you have to get the right card. They are copied a lot, many look the same and many don't work.
Awesome information buddy alot easier than i thought. Definately setting up the sonicwake tomorrow!
cheers thanks again
Build her oronclad
I noticed your flying escs, and since you're using them, I grabbed a couple of 150.
Going for torque with moderate run.30, 35 ish.
For the hooligan feeling I use the gaser. It rocks.
I had good speeds and also lots of smoke😁😁😁
No not the magic smoke. I like the flycolor esc there been 👍 great
Perfect vid. Thanks Big B
Thank you for this video IronClad! Very helpful in setting up our BJ 24 with the Lepord 3660 motor. Just did some testing and had 2 questions. What will cause the ESC / Motor to cut out on a full trigger pass? Once you go back to neutral and apply trigger again it was back on. Secondly...it went into low battery protection mode but I still had 10.8 volts left in the battery. The ESC is set to 3.4 volts on the battery protection mode. Thank you bud!
More than likely it's your prop the prop may be too big for your setup go down and prop size see if it's still power cuts if it's still power cuts the KV of your motor may be too high
@@IRONCLADRC thanks for your reply it’s just the stock prop th kV I THINK IS 2550
Does the low voltage cut-off stop the boat dead or go into 'limp' to allow you to get to the lake / pond edge?
Usually goes into limp mode or a momentary/quick cut off
thanks dude. The engrish instructions do not make it clear to hold full throttle down all the way to your selection. Also note: maybe its my remote, but neutral wasnt enough, i had to puch pistol throttle full reverse to be acknowedged by ESC.
Hey big B got a questions about new flycolor 90 I put in a bj24. First two runs were flawless. 3rd run, I plug battery in and try to throttle up, motor doesn’t make any revolutions, it just jitters back and forth and instantly heats up to 165° within seconds. Motor wires from esc get hot. Esc arms fine, but won’t turn motor. I replaced the esc with stock one and motor works fine. Have you seen this problem with any flycolor? Defective maybe?
Probably single phasing, Check the esc/motor connectors peel off the heat shrink on the esc/motor wires. You more than likely desoldered a bullet. If that's the case, re-solder the bullet. Also, consider upgrading the connector size to a larger bullet
I’m running 2 3660 2070KV outboard with 2 fly color 90amp, they came with 35mm props I bought 38mm props with a counter rotating prop how do I program my esc
My brandnew Proboat Recoil 2 Shreddy broke my esc (hobbywing 100amp 3s-4s esc.. after 1 minute it stopped only my steering was working but no throttle.
So i orderd the Flycolor 150amp esc. I hope this will hold longer on 4s
If your running the stock motor the flycolor 150 won't work with it.
@@IRONCLADRC why not, because the specs says "2s - 6s"
I wont run 6s only 3s or 4s then it should not be a problem isnt it?
I have allot of Rc cars running a stock 3s or 4s motor with an 150a or higher esc on it just to have over kill on amps. Why couldnt this work on a boat? (Honost question)
@@IRONCLADRC why not, because the specs says "2s - 6s"
I wont run 6s only 3s or 4s then it should not be a problem isnt it?
I have allot of Rc cars running a stock 3s or 4s motor with an 150a or higher esc on it just to have over kill on amps. Why couldnt this work on a boat? (Honost question)
Hi Big B,, that's a really informative video, now comes the question,, this stuff is all new to me, my Boat can run on 4s and 6s obviously with the smaller prop for 6s
I bought the boat second hand and its set to run forward and backwards which has helped on the rare occasion I've got in a tight spot, so should I alter the settings each time I want to use 4/6s batteries, it came with the 4s prop on. I had to buy the 6s prop, so I'm assuming it's setup for 7-4v, I've run it on 6s once not knowing about these adjustments, will it have come to any harm? I've just downloaded the instruction part of the manual for these settings,
Your thoughts would be appreciated bro
(Joysway Alpha)
No the settings should be OK switching from 4s to 6s. Unless your tinkering with timing. On 6s I'd be careful with high timing or to low of timing. Always watch your temps
@@IRONCLADRC thanks for the reply, having now just looked at the factory settings diagram it's preset to forward and backwards, and auto battery detection and preset timing,
Learning all the time bro thank you for your videos I love them,
And a big congratulations to the addition to your family, 🇬🇧
What would cause my boat to get up to full speed 5 seconds is all i get....shuts down ... 5 sec later it will fire up and just repeats it again. Bringing it back at 25% throttle andnits ok.?
Спасибо товарищ
You're an animal with rc dude. Hey question, is opting for "forward only" a preference or is not advisable on fast electrics? I understand race rules etc. I guess once you understand your boat and how it slows down you wont need reverse. Guessing here. 🤔
Подскажите пожалуйста, как ESC узнает максимальный ток моего двигателя?
Я имею
- двигатель 50v max 40A max, 70KV. -Батарея 36v(32-41в), BMS 40A cutoff,
- FLYCOLOR FLYDRAGON ESC 12S 80A-V2. Использую двигатель на SUP. Как запрограммировать ESC ток потребления батареи не выше 40A?
Hello. can you use any remote control? do you have to connect them first? or is it already connected to the receiver anyway?
You need to bind a rx/TX first.
Hello. I am going to build a robotic boat using a Flycolor 150A ESC, controlled by Arduino. Can I somehow do a similar calibration with Arduino, or a program card is needed?
Unfortunately I don't have any experience with arduino, all I can say is give it a shot, flycolor does offer a program card
@@IRONCLADRC Thanks! Also, can I use the same ESC in a RC car (to save money) with a fan attached? Will it overheat?
why don't you like having reverse?
Reverse will unravel a flexcable especially if you go to hard in Reverse
Hi. is it possible to program my Feilun ft011 in this way? Where can I find the instructions for the stock ESC? or is that impossible? greet Benjamin.
Not sure buddy wish I could gelp
Do they sell program cards for these flycolor esc's? thanks
Yes
Man I've gave you about 200 views on this video last couple days. I've been doing same thing as you but it runs the motor full throttle in the neutral position and throttle stops when I pull the trigger..I've tried the reverse switch on transmitter but same thing..almost starting to wonder if the transmitter came with the trigger wired backwards...have you ever seen that before. It's just a cheap flysky remote picked up on Amazon. You got any ideas what I'm doing wrong?
Dial your dual rate down to zero. If that doesn't help dial it to zero then recalibrate the esc
Thanks for the quick reply..ok yeah I'll try that! Subscribed!!
And yes that worked!! Thanks!!
Thanks!
Thank you. Glad I could help. BG4L
Thank u keep up the good work . Love watching them
Been looking at these online for my bj24 cant find very many reviews on them how do you like them? Also everything ive read about the stock prop size and pitch for the bj24 is all over the place and the measurements in the manual are not what the prop on boat measures any idea what the actual pitch and size is?
Flycolor esc's are awesome that's really all I run in my boats. It's been so long since I used the stock prop I hate to tell you something wrong.
As for upgraded props for the blackjack 24 I'd definitely go with a tfl 438 or ose 438 size prop it's my go to prop. 440 is also a good one for the boat
Thanks for the quick reply, sweet sounds like ill be ordering a flycolor 90 soon and a surpass hobby 3250kv haha the 440 and 438 props from ose are outta stock but i got a cnc prop comin with same specs as the m440 and a cnc prop with the same specs as the octura x438 we will see how she does!
Necesitó tu ayuda, tengo la Flycolor 90A , tengo la tarjeta configuradora, la he configurado bien , pero en todos los casos me funciona de esta forma, el gatillo de la emisora en reposo (0%) el motor se pone al 100% y para pararlo tengo que presionar el gatillo al 100% , pero el problema es que con esa configuración si suelto el gatillo o pierdo la señal el barco se perderá
You need to set your throttle dual rates to zero and go thru the start up process again
@@IRONCLADRC perdoná mi ignorancia, como se hace eso?
Michas gracias
My motor makes a continuous beeping sound when I use a maytech remote and try to calibrate esc. Remote is paired and powers motor but unable to calibrate or enter programming mode.
Check the dual rate make sure it's at zero
@@IRONCLADRC it's a fairly basic remote with only throttle and brake. No way to modify or set dual rate. Motor doesn't engage till 54% throttle and remotes pwm range is 1-2ms. I'm assuming the esc starts at 1.5ms and can't be changed?
Have you tried to re-bind the rx/tx? I'd try to re-bind with the esc
@@IRONCLADRC yes I've also tried that. I'm at a bit of a loss as others are successful with the same setup.
I have a question, my 150a esc had throttle position warning. So if you turn your transmitter on with throttle on, instead of entering program mode, it just sits on constant beeping throttle on warning. Is there a way around the warning to get into programming mode? Thanks!
I'm fairly positive the start up beep beep beep beep beep than a musical tone is called soft start up. 2 of my boats do that with fly color and the other flycolor does not? Hope this helps if not shoot another comment
@@IRONCLADRC Unfortunately no, my start up beeping is constant and does not stop. The manual says that constant beeping on start up means the throttle lever is not in neutral position, but you have to have it at full throttle to enter program mode. I'm wondering if I may have to re-calibrate the throttle position...
Yep that's exactly what you need to do rx recalibration should do the trick
@@IRONCLADRC yep, that fixed it! Thanks for your help.
I'm having this same issue, constant beeps. I'll re-callibrate the rx. Thanks fellas!
Mine beeps but no musical tone 😓 I’m not sure what to do.. please help
Make sure the your in full positions when the battery is plugged in
Hi can you help me about on my esc flycolr 150a.
What's your problem? I will do my best
I fumbled my way through programming the flycolour 150a in my son’s Spartan.
If the transmitter gets out of range of turned off while the boat batteries are hooked up. Is there a way to fix that ? We ran the boat out of range and it kept turning the prop at a reduced rpm.
Hi I’m new at this I just got one of those ESC 70A for one of my boats but when I connected all I get is a constant beeping I haven’t been able to pass that point, all I get is a constant beeping and the motor shakes left and right. Any idea what it could be and what am I doing wrong. Thank you. 👍👍
Esc này morfet mấy chân
Thanks!