@@heroharo unfortunately you need to have one of those two pieces of information. Either the installer code or the panel ID and password. The whole point of these is to prevent others from taking over your panel. If the panel is not locked you can factory reset it. To find out if it is locked, power cycle it. If it is locked you will hear the relay clicking. If it is not locked it will just startup.
Of course if you power cycle it you will get timer loss trouble and you will need to adjust the clock. Also keep in mind if you factory reset the panel (assuming it is not locked) you will wipeout all the programming
Many thanks for the video. Unfortunately K32IRF does not have single key background. I would share a video with you what I can see on my K32IRF. Do you have an email address for that?
I am not sure what you mean by "does not have single key background". I checked my instructions with a K32 and it worked. K32 doesn't have a 0. The 10 lights up instead. You can post an unlisted video and put the link in the reply.
Thans fo the hint, it works. Is there a way tu update IP150 without a panel connected just give it power? Where can i find downloadable firmwares for it?
@@sedky69 Thans fo the hint, it works. Is there a way tu upgrade the IP150 without a panel connected just give it power? I bought an IP150 firmvare v4.1 and I can login to the webUI of it, but I cannot connect to the panel through the IP150. So either the IP150 is wrong or the serial port is disabled for the SP6000?
@@gabortoth3374 I have never tried that. Try connecting using the static ip. Make sure the ip module is connected to the serial port of the panel. The one on the top right of an sp6000. There are two ports that are similar and it is easy to confuse them if you are not familiar with the panel
@@sedky69 I connected to the right port (the other one has five pins). I am clueless what might be the problem. Is there a setting of the panel to enable / disable the serial port of it?
Thank you for video, is there a way to get Installer code, if i have only master code? Thank you
You can get it if you have the babyware software, but you need the panel ID and password. I assume you are an end user?
@@sedky69 yes i am, i have babyware, but login fails as i dont have pc password as well
@@heroharo unfortunately you need to have one of those two pieces of information. Either the installer code or the panel ID and password. The whole point of these is to prevent others from taking over your panel. If the panel is not locked you can factory reset it. To find out if it is locked, power cycle it. If it is locked you will hear the relay clicking. If it is not locked it will just startup.
Of course if you power cycle it you will get timer loss trouble and you will need to adjust the clock. Also keep in mind if you factory reset the panel (assuming it is not locked) you will wipeout all the programming
unfortunately you may have to replace the panel
Many thanks for the video. Unfortunately K32IRF does not have single key background. I would share a video with you what I can see on my K32IRF. Do you have an email address for that?
I am not sure what you mean by "does not have single key background". I checked my instructions with a K32 and it worked. K32 doesn't have a 0. The 10 lights up instead. You can post an unlisted video and put the link in the reply.
Thans fo the hint, it works. Is there a way tu update IP150 without a panel connected just give it power? Where can i find downloadable firmwares for it?
@@sedky69 Thans fo the hint, it works. Is there a way tu upgrade the IP150 without a panel connected just give it power? I bought an IP150 firmvare v4.1 and I can login to the webUI of it, but I cannot connect to the panel through the IP150. So either the IP150 is wrong or the serial port is disabled for the SP6000?
@@gabortoth3374 I have never tried that. Try connecting using the static ip. Make sure the ip module is connected to the serial port of the panel. The one on the top right of an sp6000. There are two ports that are similar and it is easy to confuse them if you are not familiar with the panel
@@sedky69 I connected to the right port (the other one has five pins). I am clueless what might be the problem. Is there a setting of the panel to enable / disable the serial port of it?
Thx , u saved me 🎉🎉🎉
Un abrazo viejo