@@middleestmidia8212 3months pehle ye tarike se kata hua vdo bana chuka hun sir,,,20lakh views mile hn,,dubara wohi tarika ka vdo kyun banaunga??😊 Sayad aap dekhe nehi,, Dekh lijiye,,
Я про провар и качество шва промолчу, но сейчас я особенно горд, что получал образование на советской платформе. Я думал Задорнов утрирует - ан нет. Беда мужик! Всё намного проще, да и 3я рука не очень нужна.
Электроды нужны, если требуется угол не 90 градусов. С его "шаблоном" ничего не вышло - поэтому на 4:05 уже трубы отрезанные на отрезном станке под 45.
I’ve made that cut freehand with a torch hundreds of times. Not a welder by trade. A Texas Rancher with many miles of 2 3/8” pipe fence, gates, and corrals. Now I am 65 and no longer help with that sort of thing. Life out here is grand.
Just a little tip rather than using the welding rods as measuring gauges just measure the outside diameter of the tube, this is the only accurate way to do this job. Personally id just buy an elbow to weld on which will create less resistance to what ever medium being transported in this pipework installation.
well that's 6 mins and 14 seconds of my life I'm never getting back lo lol but that 3 hands thing was bloody amazing well worth watching this vid for lol lol
I love the trick with the measuring and the paper! I think you can get even better results by: - Grinding a little angle at the pipes after cutting so you have a V-notch into which to weld - Clean up the pipes a bit more prior to welding to make the weld flow better - Pull one weld instead of multiple spot welds after one another - You will get chunks of oxide layer get stuck in-between like this - Please don't use a cutting wheel on your grinder for shaping those round edges. use a thicker wheel for that. Otherwise, you might hurt yourself by the thin cutting disk breaking
Yes I was going to say that one pull instead of spot welding. The weld will penetrate better. And l used to do it that way but my welding teacher said that's cheating and not good penetration.
Отличное решение! У меня всегда была проблема с соединением труб под угоом 90 градусов. Я не понимаю тех людей которые поставили👎дизлайк. По всей вероятности, что это категория диванных экспертов, которые по жизни, кроме прожигания своей жопой дивана ничего не делают. За видео👍+подписка. Продолжай в том же духе, на пользу людей.
Дизлайк поставили те, кто заметил, что на 4:05 трубу подменили на отрезанную на отрезном станке. Хорошо видно, что торец не подпиленный шлифмашиной в руках, а отрезанный ровным пилом за один проход.
No, because you don't "think different". Here are some words for your edification: "Think and Act Different, Use you Imagination, not the example of others" I'm confident that with enough imagination, a 'one handed man' could do it even better.
@@Phoenix-One0922 I'm confident even using my imagination..... I have ZERO clue, as to what your talking about .....much LESS, your "point". Even WITH....three arms.
My God you are tradesmen You're doing it the way things were done without the specialist which makes you the specialist You've got some haters posteing but you're you're good The people that call other people to fix stuff at their house either Appreciate a tradesman or are jealous especially if they're men Stay creating my friend
Excelente "explicacion"??? Cual? si nunca dijo una palabra! Querras decir 'demonstracion'... Nunca falta alguien para decir tarugadas... Ademas este chavo es de la India... A poco entiendes Hindi guey? Me dueles Mexico...
This is actually a great way to cut 45s. Especially for does of us working in Pharmaceutical or Manufacturing industry .First time right. Especially if u were using 316 SS, it is not cheap.. Garage and mickey mouse fabricators would not understand.
@@rajandseema123 What the hell is going on in the pharmaceutical business. Are you telling me you use this method to cut tablets? Maybe that's why I'm getting L shaped tablets stuck in my throat.😧
nao e rapido nao semplice , il risultato e scarso , (saldatura perssima.taglio molto impreciso,e se mette una squadra vicino si vedrà che angolo che dovrebbe essere 90 gradi e chiuso ) ci sono altri modi più semplici
@@manuelpinzagli8091 que buen ojo para ver que el ángulo no es de 90 jajaja. Lo punteó con la escuadra magnética, porque decís que no está a 90? Ganas de criticar
I loved this. All your"how to" clips are so helpful, thank you. I'm a new welder and your channel is my first stop. Be well my friend and thanks again.
Complete welding newb here, but after you cleaned that weld up it looked like there were heaps of divots and holes in the actual weld. Im building up to eventually tackle my own bar work. How strong would that weld be in an impact situation?
Incredibly weak is your answer. never do this. Especially with 6010 stick. If you want a strong weld use the proper welding process for the right material if your going to be welding thin Guage material like in the video use tig welding or MIG welding. And never tack an entire joint. Run full beads.
@@danzig159 what does a key hole have to do with welding thin Guage tube stock? A key hole is formed from open root stick and tig welds done on thicker gapped grooved joints from 3/16 to 1/8th in gaps. Good enough for you? If you want a strong weld that can withstand impact you weld a full bead, this tacking bullshit only leads to inconsistency, gaps, holes, and slag inclusions in the weld joint.
Buddy 6010s holds 60,000 psi of pressure it’ll be strong enough he just needs to stay on there a little bit longer and not come off and go back on and just step with a lower temperature and I’ll be perfectly fine for Alex trying to go over with 7018 that holds 70,000 psi of pressure Meg is OK and so is Tig They’re all strong
@@brantnassar642 when I mention “especially with 6010 stick”, I’m referring to how hot and volatile it runs as the purpose of most types of 6010 rods is to get deep penetration within your base material. It’s really not ideal to tack all the way around a corner but joint like that made out of thin material because of you likely hood of getting arc blow and gouge. another issue of tacking a joint together like that is the constant heating and cooling of that joint and previous tacks changes the hardness of the tack weld causing the tack to become brittle and easily break if the joint were to come under stress. The joint absolutely has a higher likelihood of having those tack welds pop or crack.
Welding strength equals zero due to no heat penetration at all. This is how you get people seriously injured or killed when fabricated like this. Any force will easily break your weld. So don't use this example if it's for anything else than a yard fence.
Muito bom, mas se fizer um molde com um pedaço do próprio tubo, em formato de abraçadeira, ficaria mais prático para fazer o serviço quando o volume de trabalho for grande.
Otro Pend... sando lo mismo. Carajo... Se toma un tubo un 1/4" de diametro mas grande que el que vas a cortar, OK? Con un carton Pre-marcas la linea "guia". Se le da un corte en 3/4 partes con un disco de corte y con la apertura de el grosor de un marcador o plumon (Un 1/8") en el tubo que va a embalsamar por fuera, o sea, con el que vas a marcar los que vas a cortar. Un corte en Linea Recta. Fabricas uno con 45 grados, otro con 30, etc... metes el tubo 'guia' por fuera y marcas el de adentro usando el corte pre-hecho en el tubo 'guia' y ya! Cual es el pinche misterio? Ya tienes un tubo GUIA pre-fabricado con lineas Rectas en Redondo para usarlo una y otra vez. Pues para que te enteres de una buena vez! Asi es como se construye una guia tubular. No le des tanto credito al Hindu este usando metodos primitivos. Acabo de inventar un buen dicho: "Piensa e' Inventa Diferente. Usa tu imaginacion, No el Ejemplo de los demas y tu nombre pasara a la posteridad" Phoenix One, August 31st, 2021 Words of a Modern Age Sage.
Todo soldador y más si es tubero, tiene que saber esos trucos y las fórmulas para unir en diferentes ángulos. Está muy bien la idea, pero no es cosa del otro mundo. Gracias por el video
Wish I had three hands.
😃😃😃🤓🤓🤓
Abe 40 mm ka pipe h.. To 40 mm pr mark dekr. Bhi kaat deta re. Right angle milta.. Kis liye ye phuddu kaam krta h kuch nya kr..
@@middleestmidia8212 3months pehle ye tarike se kata hua vdo bana chuka hun sir,,,20lakh views mile hn,,dubara wohi tarika ka vdo kyun banaunga??😊
Sayad aap dekhe nehi,,
Dekh lijiye,,
Hai
@@ashokanmm1317 Hello Sir❤️🙏
Я про провар и качество шва промолчу, но сейчас я особенно горд, что получал образование на советской платформе. Я думал Задорнов утрирует - ан нет. Беда мужик! Всё намного проще, да и 3я рука не очень нужна.
Электроды нужны, если требуется угол не 90 градусов.
С его "шаблоном" ничего не вышло - поэтому на 4:05 уже трубы отрезанные на отрезном станке под 45.
Set your chop saw @45°,put a reference mark for top. Cut it, clamp & weld.
AMAZING
Sir,,I already many videos that's ideas,,
Please see my playlist
He's showing a different technique maybe for those who don't have chop saws.
I have chop saw but this is how to cut without shopsaw,❤️🙏🏻👍
Ayos Galing hirap na hirap ako mag cut ng GI PIPE na naka Angle ganyan pla ang accurate cut Ayos
Thank You Sir😀👍❤️
I keep falling asleep to the music, is this one of those relaxation deep sleep videos. It sure is re……..
❤️🙏👍😀
Me too...i woke up thinking i cut my hand while sleeping through this video
Thanks for the flash burn. lol
Who else reflexively closed their eyes and thought "D*&k! Come on man. Eyeballs!"
FAB2KU: YOU ARE AWARDED EURO-BUILD MEMBER. CONGRATULATIONS!
🤓🤓🤓🤓🙏🏻👍👍
Thank You😀
Bueno fácil y práctico,y rápido sobretodo trabajos en terreno que heran pará ayer, muchasgracias Díos los cuidé de todo mal,de Chile.
👍🙏
That cardboard trick is the winner!
😀🙏👍❤️😀
this is great video, thanks for sharing
Welcome Sir🙏
Thanks For Your Great Love❤️🙏👍
I’ve made that cut freehand with a torch hundreds of times. Not a welder by trade. A Texas Rancher with many miles of 2 3/8” pipe fence, gates, and corrals. Now I am 65 and no longer help with that sort of thing. Life out here is grand.
🙏😀🙏😀🙏
Wow amazing technique
Thank You Sir❤️🙏👍
Just a little tip rather than using the welding rods as measuring gauges just measure the outside diameter of the tube, this is the only accurate way to do this job. Personally id just buy an elbow to weld on which will create less resistance to what ever medium being transported in this pipework installation.
🙏👍🙏😄❤️
14" cut off blade, make these 2 cuts in 2 minutes
👍🙏❤️
You are very correvt
@@atstancioffl😅😊
well that's 6 mins and 14 seconds of my life I'm never getting back lo lol but that 3 hands thing was bloody amazing well worth watching this vid for lol lol
I read ur comments so I decided to save those 6 mns hhh
@@omarbeuleum1264 madadgjklghop
@@omarbeuleum1264 ttr ttyttu555uuuyuuyuyru
Нравится толкового и без лишних зачисток и малая трата времени на просмотр . спасибо за ваш труд
Thank You sir 😀🙏👍
Good technique. Geometry was involved 👍
Thank You Sir🙏❤️👍
Just get the diameter of the pipe and pass it on the one side of the pipe and line it diagonally for cutting.
i have made a video in this way sir,,then i made this in second tricks
Ronnie Lumanog I could not understand why he did not do what I was thinking and what you posted.
well said... and USE a welding helmet too, uh? They never do...
@@Fab2Ku mmk man k kk mm mm
M mm y
.
But what if u dobt have a tape on hand or near by....cool trick
Bellissima video bravo buon lavoro grande professionista molto❤️❤️ prechiso perfect 🤝🤝🤝🤝🙏🙏🙏🙏💪💪💪💪💪💪💪💯💯💯👍👍👍👍👍👍👍👍👍👍👍👍👍
Thank you so much sir
What a brilliance.Oscar waiting for you.,
😀😀😀😀
Keep support sir
Very well done but setting the vise on the chop to 45 degrees is easier.
👍❤️🙏
@@Fab2Ku Looks like you will always need a chop saw with a 45° setting to do any work
I love the trick with the measuring and the paper! I think you can get even better results by:
- Grinding a little angle at the pipes after cutting so you have a V-notch into which to weld
- Clean up the pipes a bit more prior to welding to make the weld flow better
- Pull one weld instead of multiple spot welds after one another - You will get chunks of oxide layer get stuck in-between like this
- Please don't use a cutting wheel on your grinder for shaping those round edges. use a thicker wheel for that. Otherwise, you might hurt yourself by the thin cutting disk breaking
Thank You Sir👍❤️🙏😀
Yes I was going to say that one pull instead of spot welding. The weld will penetrate better. And l used to do it that way but my welding teacher said that's cheating and not good penetration.
@@jasonyork4418 you can make bevel also before fit
Сварщик от бога!)
😀🙏👍
All types of Aluminum & Glass work
1)2 & 3 sliding,openable windows(Madras & Domal).
2)Aluminum partitions & Doors.
3) All types of Aluminum doors.
4) S S & MS Railing.
5) ACP works.
6)Structural Glazing works.
7)Mosquito Mesh doors.
8)All ceiling works (POP,Gypsum board & Grid).
9)All wardrobes (Aluminum & Wood).
10) Aluminum sliding cupboards.
11) All glass works.
Building Elevations
That compound cut is awesome. Good job young man.
This is an awesome tradesman here 👍🏻
Thank You Sir🙏😀❤️
Nice idea for beginners or home DIY projects. But thanks to chop saw which can cut in any angles. ✌✌
Yes sir,,thank You👍🙏❤️😄
Çüpç..
Lço.p.
O
P.
.
.
..
.
...
O..
.
...oı
.o.
O
.
Isı .oooo
Muchas gracias x tomarte tu tiempo para enseñarnos y mostrar genialidades que simplifican nuestro trabajo genial amigo!!!!
Thank You Sir❤️🙏🙏🏻
Super amizing good job brad because of your vlog tutorial I got some knowledge from you
Thank You Very much Sir🙏👍❤️
Отличное решение! У меня всегда была проблема с соединением труб под угоом 90 градусов. Я не понимаю тех людей которые поставили👎дизлайк. По всей вероятности, что это категория диванных экспертов, которые по жизни, кроме прожигания своей жопой дивана ничего не делают. За видео👍+подписка. Продолжай в том же духе, на пользу людей.
😣😣👍
Дизлайк поставили те, кто заметил, что на 4:05 трубу подменили на отрезанную на отрезном станке. Хорошо видно, что торец не подпиленный шлифмашиной в руках, а отрезанный ровным пилом за один проход.
Мало того что трубы варили резанные за один проход, так ещё и сварной шов никуда не годный. Дизлайк не поставил, но и хвалить не за что...
Thats Amazing. I wish I had 3 hands sometimes.
🤓🤓🤓🤓🤓👍🙏🏻
Excellent job and you make it look so easy, I guess it’s because you have four hands.
Thank You so much sir
I watched this guy,
I could never do it like that !
He has 3 hands.
Ha ha ha ha🤣🤓
No sir,,I have 2 hands
ruclips.net/video/vEclZ68uJSc/видео.html
ruclips.net/video/FpzPEPqhlrc/видео.html
ruclips.net/video/pv3dWpYoyK0/видео.html
ruclips.net/video/6M6iRj45Yr8/видео.html
ruclips.net/video/3cpFE9hinDo/видео.html
No, because you don't "think different". Here are some words for your edification: "Think and Act Different, Use you Imagination, not the example of others" I'm confident that with enough imagination, a 'one handed man' could do it even better.
@@Phoenix-One0922 I'm confident even using my imagination.....
I have ZERO clue, as to what your talking about
.....much LESS,
your "point".
Even WITH....three arms.
Под углом 45* опускаем в известковый раствор (или иной красящий). Сушим, отрезаем закрашенную часть. Соединяем. Идеально.
👍🙏🏻❤️😀
Excellent idea ... Salute for you and your generous idea
Many many thanks
Wow thank u, the best idea i’ve ever watched
Thank You🤓🙏❤️
Two piece 45° elbow to be cut 22.5° both ends of pipe.
To form 45° elbow.
👍👍👍right sir
The BEST technique listef ...and will be one ever
It's simple❤️🙏🏻
Thank You sir
This skill is for those who are just learning to be a welder
Yes sir👍😀🙏
I'm 73 and I was developing 90degree elbows on paper to wrap around d pipes when I was 16 .this is rough fabbing,
I've used a many wrap one of the best tools in my tool box next to my center punch
My God you are tradesmen You're doing it the way things were done without the specialist which makes you the specialist You've got some haters posteing but you're you're good The people that call other people to fix stuff at their house either Appreciate a tradesman or are jealous especially if they're men Stay creating my friend
vedendo un filmato del genere un tubista si sganascia dalle risate!
🙏👍🤓❤️
Excelente explicación muchas gracias por compartir sus conocimientos saludos desde Guadalajara
Thank You Sir🤓🙏❤️
exelente otra muestra
@@antolinmedina1067 thank you sir🙏❤️💐
Excelente "explicacion"??? Cual? si nunca dijo una palabra! Querras decir 'demonstracion'... Nunca falta alguien para decir tarugadas... Ademas este chavo es de la India... A poco entiendes Hindi guey? Me dueles Mexico...
@@Phoenix-One0922 ❤️🙏😄👍
Simple but excellent brother unlike others.thank you so much your idea
Thanks for your great support Dear Brother
This must be the most inneficient way to cut 45 degrees.
Thank You sir❤️
Rolf , can you suggest a better way
This is actually a great way to cut 45s. Especially for does of us working in Pharmaceutical or Manufacturing industry .First time right. Especially if u were using 316 SS, it is not cheap..
Garage and mickey mouse fabricators would not understand.
@@rajandseema123 What the hell is going on in the pharmaceutical business. Are you telling me you use this method to cut tablets? Maybe that's why I'm getting L shaped tablets stuck in my throat.😧
@@jameslangan7357 Sir, this is a different trick of pipe cutting, by the way, I have make more videos, but its have tried to separate from them.
Simple , rápido , eficiente , muchas gracias por compartir tus conocimientos. Saludos desde Arica Chile
Thank You Sir❤️👍🙏😃
nao e rapido nao semplice , il risultato e scarso , (saldatura perssima.taglio molto impreciso,e se mette una squadra vicino si vedrà che angolo che dovrebbe essere 90 gradi e chiuso ) ci sono altri modi più semplici
Chop saw, 45
@@manuelpinzagli8091 que buen ojo para ver que el ángulo no es de 90 jajaja. Lo punteó con la escuadra magnética, porque decís que no está a 90? Ganas de criticar
WE the people, MUST commend you, sir, on the choice of music. Very mellow.. Beautifll touch !!
Thank You SIR❤️👍🙏🏻😀
Perfeita a demonstração desde o início ao fim. Com simplicidade e muita criatividade, é possível fazer quase o impossível.
Shut up, you happy Brazilian... tudo e' perfeito, tudo e' bom pra voce! que felicidade... esta loco. Fala a verdad...
Perfect
@@Phoenix-One0922 Sou feliz por reconhecer habilidades em meu semelhante. O sucesso compartilhado é fruto de sabedoria e gratidão!
❤️🙏🤓
Попробуй повторить это и ты исправишь свой комментарий.
Yery good 👍👍👍💯❤❤
Thank You Sir
excellent ഫാബ്രിക്കേഷൻ
Thank You👍🤓🙏
I found out today that double tapping on a comment will like the comment
Thank you so much sir 🙏
Meus parabéns.
Deus te abençoe.
Super dica
Thank You Sir👍❤️
𝐀𝐚𝐩𝐤𝐚 𝐡𝐢 𝐣𝐥𝐰𝐚 𝐡𝐚𝐢 🤟❤️
😀😀😀😀
Sab aap logon ka sath se hua hai sir❤️🙏👍😀
I loved this. All your"how to" clips are so helpful, thank you. I'm a new welder and your channel is my first stop.
Be well my friend and thanks again.
Thanks For Your Love & Support Sir🙏❤️😀👍
Thanks for your teaching. I have learnt a lot of skills.
Welcome Sir
youtube.com/@DabhiBharat143?sub_confirmation=1
Хорошо когда у тебя три руки, удобно
Thnk You❤️🙏
Good job bro good luck
Thank You Brother🙏❤️🤓
Complete welding newb here, but after you cleaned that weld up it looked like there were heaps of divots and holes in the actual weld. Im building up to eventually tackle my own bar work. How strong would that weld be in an impact situation?
Thank You Sir😀👍❤️🙏
Incredibly weak is your answer. never do this. Especially with 6010 stick. If you want a strong weld use the proper welding process for the right material if your going to be welding thin Guage material like in the video use tig welding or MIG welding. And never tack an entire joint. Run full beads.
@@danzig159 what does a key hole have to do with welding thin Guage tube stock? A key hole is formed from open root stick and tig welds done on thicker gapped grooved joints from 3/16 to 1/8th in gaps. Good enough for you? If you want a strong weld that can withstand impact you weld a full bead, this tacking bullshit only leads to inconsistency, gaps, holes, and slag inclusions in the weld joint.
Buddy 6010s holds 60,000 psi of pressure it’ll be strong enough he just needs to stay on there a little bit longer and not come off and go back on and just step with a lower temperature and I’ll be perfectly fine for Alex trying to go over with 7018 that holds 70,000 psi of pressure Meg is OK and so is Tig They’re all strong
@@brantnassar642 when I mention “especially with 6010 stick”, I’m referring to how hot and volatile it runs as the purpose of most types of 6010 rods is to get deep penetration within your base material. It’s really not ideal to tack all the way around a corner but joint like that made out of thin material because of you likely hood of getting arc blow and gouge. another issue of tacking a joint together like that is the constant heating and cooling of that joint and previous tacks changes the hardness of the tack weld causing the tack to become brittle and easily break if the joint were to come under stress. The joint absolutely has a higher likelihood of having those tack welds pop or crack.
Wow, perfect!!!
Thank You Sir❤️🙏💐
Lebih mudah carany ya bang lanjut terus dan sukses selalu salam dari Dadun Azkan
Thank You Sir❤️🙏
É o que eu precisava!! Genial!!!
Thank You Sir
youtube.com/@DabhiBharat143?sub_confirmation=1
Incredible idea
Thank You🙏🏻🤓
X
Nice idea, Without use paper, I love it....❤💓
Thank You Sir
You know you could just 45 those on a chop saw and be done with it
❤️👍🙏🏻
Exactly what i was thinking
Not all do have that chop saw.
Or quarter the pipe, mark the cut back and use a wrap-a-round to mark the profile
Muito bom aprendi mais uma !!!parabéns !!!
😄👍🙏
Buenas noches hermano gracias por compartir sus conocimientos saludo desde Venezuela Edo Carabobo Ali Molina bendiciones 🙏
Thank you so much sir
Welding strength equals zero due to no heat penetration at all. This is how you get people seriously injured or killed when fabricated like this. Any force will easily break your weld. So don't use this example if it's for anything else than a yard fence.
🙏❤️👍👍
Vivendo e aprendendo. Simples e eficiente.
Thank You🙏🏻👍❤️
Very good trik 👌👍
Thank You Sir🙏👍❤️😀
Excelente trabajo me parece muy fácil para los q están comenzando en el mundo de la herrería le felicito maestro.
Thank You Sir👍🙏🏻
@@tatumergo3931 exacto, en algo sencillo lo hizo ver un poco tardado
Parabéns! Muito bom! Deus Abençoe 🙌
Thank You Sir🙏❤️
youtube.com/@DabhiBharat143?sub_confirmation=1
Good job very effective content
Thank You Sir🙏❤️👍
Didn't grind the scale off, didn't vee out the mating surfaces and didn't get any penetration because you just tacked it the whole way around.
😳... Muy bueno, gracias
🙏🏻😀👍❤️
Wow ang galing
Thank You Sir❤️🙏👍😀
Trabalho excelente, simples e eficiente. Parabéns.
Thank You🙏❤️
@@Fab2Kumi
youtube.com/@DabhiBharat143?sub_confirmation=1
I think it's 90 Degree not 45
Yes Sir..
But I cut both pipe at 45 degrees..
Yes, the cut is 45, × 2pipe = 90.
Браво.👍👍👍спасибо за информацию
Thank you so much sir
Bem prático para o que eu aprendi a calcular com medidas.
🤓👍❤️🙏🏻
George ibay
perfeito, parabéns!🤗🤗🤗🤗🤗
🤓🤓🤓👍❤️🙏
Да показана за 6мин а бодгонял пол часа новерно
Wow great video
😄👍🙏
@@Fab2Ku 😏😏
Muito bom, mas se fizer um molde com um pedaço do próprio tubo, em formato de abraçadeira, ficaria mais prático para fazer o serviço quando o volume de trabalho for grande.
Thank You👍🙏🏻
2:08 а зачем такие сложности? что не ясно что длина отмеченная на электроде равна диаметру трубы!
❤️🙏👍
Человек третью руку отрастил, ради замера. А вы не оценили )
В нашей деревне давно угларезами пользуемся, тут столько художества.
@@ТемныйПринц-ш3ж I can't read your language sir,,,pls write in english
Просто геометрию в школе не учил..
الله ينور عاليك
😀❤️🙏🏻👍
Para que me hubiera enterado antes, siempre realice complicados trazos, para realizar ese tipo de cortes en diferentes diámetros de tubos
Thank You Sir,,
Otro Pend... sando lo mismo. Carajo... Se toma un tubo un 1/4" de diametro mas grande que el que vas a cortar, OK? Con un carton Pre-marcas la linea "guia". Se le da un corte en 3/4 partes con un disco de corte y con la apertura de el grosor de un marcador o plumon (Un 1/8") en el tubo que va a embalsamar por fuera, o sea, con el que vas a marcar los que vas a cortar. Un corte en Linea Recta. Fabricas uno con 45 grados, otro con 30, etc... metes el tubo 'guia' por fuera y marcas el de adentro usando el corte pre-hecho en el tubo 'guia' y ya! Cual es el pinche misterio? Ya tienes un tubo GUIA pre-fabricado con lineas Rectas en Redondo para usarlo una y otra vez. Pues para que te enteres de una buena vez! Asi es como se construye una guia tubular. No le des tanto credito al Hindu este usando metodos primitivos. Acabo de inventar un buen dicho:
"Piensa e' Inventa Diferente. Usa tu imaginacion, No el Ejemplo de los demas y tu nombre pasara a la posteridad" Phoenix One, August 31st, 2021 Words of a Modern Age Sage.
отрезал хорошо,но сварщик не в п...у,ток бы прибавил хоть...
Thank You Sir🤓🙏❤️
Труба тонкостенная , боялся прожечь, а так норм
и градус в конце не 90°
സൂപ്പർ ആയീട്ടോ 👍👍
Thank You👍❤️
А я все делаю на глаз, зазор не позор😊, сварщик заварит, зашлифуется.
❤️🙏
Правилно
Pourquoi faire une liaison à 45° alors qu'il existe des coudes, qui permettront un écoulement plus facile...
Bertrand.
Euh cela coute moins cher...
Der Macht das so kompliziert ! Nimm doch eine Gärungsege !!!!😝
🙏👍🙏❤️
Super bro iam welder from India Kerala
I am from ODISHA
2:10 measuring the diameter does not need to use welding electrodes. just stick the end of the pipe .. the diameter is certain.. 😆🎵🎼🔊🎶😺😁⛷🤭🤔
❤️🙏❤️🙏❤️🙏
Электроды нужны, если требуется угол не 90 градусов.
Buenazo, gracias por la lección, yo tenía otra técnica pero no era tan buena como está, ahora está nueva lo aplicaré a mis trabajos con tubos.
Thank you sir
Спасибо !!!!!!!
Как хорошо , что я наткнулся на твоё видео !!!!!
Todo soldador y más si es tubero, tiene que saber esos trucos y las fórmulas para unir en diferentes ángulos. Está muy bien la idea, pero no es cosa del otro mundo. Gracias por el video
🙏❤️👍😀
Great ideea
Great video
Great like from România
Thank you ❤️thank you❤️ Thank you ❤️
Very much sir🙏👍😀
success for "Fab2Ku"
Thank You Sir
Гап йўқ. Қойил 👍
Thank you sir
simple way ! than other vlogger ty!
Welcome!!
5 dakikada yapılacak işi 1 saate nasıl sığdırmış harika bir yetenek
👍😀🙏
New friend Goodluck, Full support Godbless
Thanks For Your Great Support Sit😀👍❤️🙏
This idea is very simple and practical easy, theory is also way but this is easy communicable,
Thank you so much sir
Asallam allykum, THANK YOU....this is GENIUS. stay well my friend. Xx
Wale kum salaam sir🙏🏻