Sir slow printing problem in canon 2900 power supply board changed as old supply has slow printing problem and paper jam notification on print command With new supply slow printing is still problem
you are a genius man mery pas hp 4515 printer ha is bht dark ground k sat print aa rha tha mane power supply ko wash kr k lagaya to ab bht light print aa rha ha plz ap batain kia kron?
Very useful information sir. HP1022 printer had "no power" issue. As per your suggestion I checked and found Mosfet and 0 ohm resistor are damaged. I replaced them both. Now while upper lid is closed, leds do not glow or blink and can not detect by PC. But if I open the lid, LEDs blinks one by one and then only Red but the motor does not run. What should I do?
informative video keep it up
Sir heater ok mosfate bhi ok hai lekin 50.0 fuser error aa raha hai
Please can u make english version of this your video please... This video is useful but understanding it is hard for us.
Hiii
Sir optocupller use to feed back voltgge me lagaya jata na
THANK SIR
Hp p1108 printer fuser not heating dc controller problem
Very informative...
Tanks for sharing
I have 1102 power supply.out put voltage have 6 volt after capacitor.dont have 24v.error door is open.which component is problem?
Optocoupler ic
Is your problem solved ?
Nice sir ji
Nice sir ❤️👍
Good video
Sir slow printing problem in canon 2900 power supply board changed as old supply has slow printing problem and paper jam notification on print command
With new supply slow printing is still problem
Check laser scanning unit
Hello, good time, engineer, can you speak Farsi?
you are a genius man
mery pas hp 4515 printer ha is bht dark ground k sat print aa rha tha mane power supply ko wash kr k lagaya to ab bht light print aa rha ha plz ap batain kia kron?
Check dry soldering & ground
Canon 6030 me hp 1007 ka power supply support karta hai?
No
अगर 0ओम का रजिस्टर नहीं रहे तो क्या करे
Jumper lgado
What is the value for hp m1005 F523 fuse resistor
Below 10 OMS
Sir mare pass hp 1022 printer hai 110 se 220 convert hai kabhi print Sahi deta hai or kabhi kacha kar rha boht ziyada plz guide kar dain
Earthing point check kro
Board ek ek chij kab kaise check kare likh kar samjye
Ok
Very useful information sir. HP1022 printer had "no power" issue. As per your suggestion I checked and found Mosfet and 0 ohm resistor are damaged. I replaced them both. Now while upper lid is closed, leds do not glow or blink and can not detect by PC. But if I open the lid, LEDs blinks one by one and then only Red but the motor does not run. What should I do?
LSU
@@trcteck What does that mean? please write in full form.
I think LSU means Laser scanning Unit. Right?
@@Smart_Electronics yes
Address bhejo me aapke pass bhej ta hu
Charge kya hai
hello please explain in english
Hi sir
Hello
Sir fuser error 50.0
heater ok hai
Power supply connector and power supply
क्योसेरा 1800 मशीन की सप्लाई बतायें
Aayega to jarur
Bhai mere printer my open Door aaraha hy hp 1007
Jha cartridge lagta upper wala cover niche dba do
Sir 1007 ka power supply 1108 me lagega Kya....
Ha
@@trcteck thank you sir but sir will the laser scanner and formatter card of 1108 work if I fit 1007 power supply in 1108??...plz suggest me sir.
No problem if all connector are same
Taransfomar kaha se milega
Scrap power supply se
Problem kya hai
Kaha par aapka office
Mera 1020 ka power board repair karna hai
Problem btao
On nahi hota
mera powersupply ka fuse bar bar kharap ho raha hain, need support
please reply
Check MOSFET short