I rarely make comments on videos, but had to on this one because it was very good. 💪 I was thinking of doing a white build for my son and this is it. I will use the same components. Great job. 👍😎
By chance do you need to use the bracket. I ordered the same gpu but it was missing a piece of the metal brackets. And am not sure if I can just install with out that part
Absolutely in love with not only the build quality, but the video production quality too. Only problem with the build is the rather noticeable Black PSU.
Thank you so much! That's right, I don't have a white PSU, unfortunately. I'll definitely keep that in mind for next time. Thanks for the great input💜🖤
Looks great! I am doing an almost identical build, except with a Kraken 280 instead of 360 and 4070 super and i5-13600K. One thing I wanted to ask, do you think it is needed to do the rear exhaust fan? I am hoping for somewhat positive pressure inside to prevent dust from coming in
Thank you so much👍👍 The overall heat from the 4070 Super and 13600K with the Kraken 280 isn't significantly high, so it's pretty fine without the rear exhaust fan. However, the exhaust relies on the radiator, so you could increase the fan speed a bit. Hope this helps!
magnificent build 👏🏼 well done!! I'm hesitant to buy the same air cooler. could you tell me your feelings in terms of noise when you play? thank you in advance
Thank you so much! I hope you meant an AIO liquid cooler. Overall, I can't say it's quiet like other AIO coolers. Since there's significant pump noise, it might be better to adjust PWM settings for the cooling fans.
That looks great other than that black aio cable. You would think after providing white tubing and a white cpu block, the could have made the other cables white also.
I’ve been looking for a long time and decided I’ll get this exact build for the wife. Also, can these be bought at MicroCenter? Thanks buddy! I also love the music. It’s gentleness helps my emotional state collect itself being one again.
yo dude the cables how did you connect the cables for the rgb fans cuz im doing what your doing with the case at least and i cant find any sources showing how to connect them little help
No worries man! In the NZXT controller, there are three RGB nodes, and each needs to be connected. In this video, two controllers were used, and a total of six nodes were connected. The remaining RGB fans were connected to the motherboard's +5V 3-pin ARGB header. All fans can be controlled through NZXT CAM. AIO RGB Fans > Used the RGB controller included with the KRAKEN 360 ELITE. Rear and Bottoms Fans > Used the RGB controller included with the F140 RGB CORE DUOE. Side Front Fans > Pre-connected with a +5V 3-pin ARGB gender connector and connected into the motherboard header. Give it a try and if it's still tricky, why don't you contact the NZXT support team? Hope this helps!
질문하나만 드리겠습니다. 오늘 배송받고 조립하다가 기존 케이스의 hdd+ hdd- , reset 등의 케이스 컨트롤 케이블이 없어서 보드에 연결을 못하게 되어 있던데요 케이스 파워는 조립완료하면 이상없나요? 싸구려케이스만 쓰다가 큰마음먹고 구매했는데 종전 케이스랑 달라서 여쭤봅니다.
안녕하세요~ 최근 몇년간 출시된 NZXT의 모든 케이스는 통합 IO 커넥터를 사용해서 그냥 메인보드 단자에 꼽으시면 되어요. 케이스를 조립하다보면 +LED -LED하고 PWR 만 있는 제품도 있고, RESET이나 HDD가 없는 케이스도 많아요. 사용에는 당연히 문제가 되지 않고요. 벤치 돌리는 PC는 그냥 전원 PWR만 연결해서 사용할 때도 있습니다.
If you use an NZXT motherboard, you can control everything through NZXT CAM. If not, it's necessary to handle the +5V ARGB separately on the motherboard.
I'm planning my first PC build with the black RGB version. Also using the 14700k, but just a RTX 4070. I was wondering if you think the NZXT Kraken 240 AIO would suffice over the 360. I was still planning on doing what you did though with the two 140s in the bottom and the 120 on the back. Awesome build and i loved your editing!!!
Oh, thank you so much! I'm glad you liked it 👍 The 14700K tends to generate quite a bit of heat, so the NZXT Kraken 240 AIO may not be sufficient. However, it could still work well if you consider aggressively undervolting the CPU or setting a power limit (at least 220-230W) when using the CPU at full load. While a 360 AIO is the optimal choice, a 240 AIO should suffice for tasks or gaming with a power consumption of around 200W. Hope this helps💜🖤
@@PC_SNAP you’re the best! Best answer I could’ve hoped for 🙏 I DID have one more tiny question about the NZXT lighting. Did you need to buy one of their rgb fan controllers? Or was the two hubs that came with the intercooler and f140s suffice (I’m PRETTY sure you can manage with two and then daisy chain the last three into a sys fan port on the motherboard??) like I said 😩 I’m a noob. Ps I’m planning on getting the NZXT usb hub as well just to make sure I’m not using up both usb ports on my motherboard. I actually may not need it at all but 🤷♂️ I’m a noob! 😂
@@TheBTeamOfficial No worries bro! First, the front NZXT RGB case fan is connected with an ARGB +5V connector cable. However, if you remove the connector, it can be used with the NZXT controller. The NZXT controller can connect three individual nodes to one device! The two NZXT 140 RGB fans at the bottom are part of the package and include the NZXT controller. Therefore, they can be used simultaneously with the rear NZXT 120 RGB fan. Additionally, the Kraken RGB version comes with the NZXT controller, so it can be used without any issues. Therefore, if you use all three NZXT controllers, you can control everything through NZXT CAM. If you want to use only two controllers, you can synchronize the front fans using +5V ARGB (mainboard header) for overall colour matching. The NZXT Kraken comes with a 2Y USB 2.0 header cable, making it convenient to connect the three NZXT controllers to the motherboard as well. :) Good Luck💜🖤
@@PC_SNAP Without sounding too dumb here, Did you use three controllers in this build and did you have to buy an extra? I'm pretty sure i'll only get two (one from the 360 kraken and one from the two pack F140s for the bottom of the case) after all is said and done with purchasing. And thanks so much for the insight on the 2Y USB 2.0 header cable! I think that means i can get rid of the extra NZXT usb 4 to 1 hub off my list. I think the included cables will take care of that.
Got it! In the video, I used two NZXT controllers. One is from the Kraken AIO, and the other is included in the NZXT RGB 2-pack. You just need to connect the front fans to the motherboard's ARGB header!
This build is 🥶🥶🔥!! You may have just inspired me to build one exactly like it since i'm in the market using the same type of hardware, and love the NZXT aesthetic. Curious what custom cables you were using (if any)? Also, i'm a first time builder, and while your video makes it look easy, could you possibly share steps or any gotchas that perhaps your video obviously would never reveal? 🙂 Looking forward to future builds!
Thank you so much!! I'm glad you liked it👍👍 Check the following link for the cables! bit.ly/46Renwf bit.ly/47LHUZd I'm editing the PC assembly video concisely and excluding unnecessary steps or poorly shot parts. If I include every step, the video will be longer, and there's a high chance it could become tedious. I'm not a professional in the PC industry and not a full-time creator. About once a month, when PC components are ready, I shoot videos. It's one of the biggest hobbies in my life. Thank you so much for your valuable opinion! I'll definitely think about it later.💜🖤
Yeah! Memory RGB, motherboard RGB, and graphics card RGB work well with GIGABYTE Fusion. The NZXT RGB core fans are controlled by NZXT CAM, and the front fan of the H6 FLOW has a +5V header, so it also operates with GIGABYTE Fusion Hope this helps!
Yo! Graphics cards above RTX 4070 use the 12VHPWR standard, which is a 12-pin connector. If it's a 16-pin connector, it would likely be 8+8 pins, so you can use the included connectors.
Check the following link! bit.ly/46Renwf bit.ly/47LHUZd The 12VHPWR cable might be okay for the 4080S, but for the 4090, it's safer to use the cable included with the PSU.
I have the same morherboard and i tried and tried to change the rgb collot on the motherboard but i couldn’t it is stuck on the rainbow puke, can you help me?
Did you use Gigabyte Control Centre? If not, first install GCC and then install the Gigabyte MB RGB Tool within GCC. If you want to change the memory RGB, you need to install the Storage Library, and if you are using a Gigabyte graphics card, you also need to install the VGA tool. Everything is completed, you can control everything through RGB Fusion (which also needs to be installed) for unified control. Hope this helps :)
During recent benchmark tests, it seems that the M.2 NVMe PCIe lane did not have any noticeable impact on the GPU performance. Any experience with this?
Got it! If the mainboard GPU and M.2 NVMe share the same PCIe lane via CPU, there may be a potential for performance degradation. However, for instance, even if there is a downgrade from x16 to x8 in the GPU lane, it is unlikely to have a significant impact I guess. Thanks for your information:)
After the build video, I disassembled the PC right away, so I don't remember it exactly. but I probably downloaded it from this link. gifer.com/en/7IsD Thanks a lot💜🖤
The case comes with a front RGB fan that uses an ARGB +5V connector. Therefore, it doesn't include an NZXT controller. I used the RGB controller included with the F140 RGB CORE and KRAKEN 360 ELITE 💜🖤
No way, what a coincidence! The RAM is quite rare, but you made a great choice. Ah~ The next video is planned for a budget PC build using the 7500F. Thanks for the comments💜🖤
@@PC_SNAP thanks for replying me, i have a 14700K (i just play games at 1440p) should i return it and grap a 7800x3d instead ? Im still on return window but i lose at least 10% of Price because i opened the packages
Thank you so much! If you actually see the case in person, it looks really good. Appreciate the comment, and I'll make sure to create some awesome PC build videos.💜🖤
This is pretty much bit for bit the build I've planned out! Glad I found your video and got the confirmation to go for it :)
Oh, you're planning a cool build setup! That's really awesome. 👍👍
Thank you so much and Happy New Year💜🖤
I rarely make comments on videos, but had to on this one because it was very good. 💪 I was thinking of doing a white build for my son and this is it. I will use the same components. Great job. 👍😎
Wow~ Your son is going to love it.
If you have any questions while building, feel free to ask anytime.💜🖤
Dude, I love your all-white vibe! Ejoyed watching this❤❤
Thank you for always watching my videos.
I appreciate it.👍👍👍👍
Excellent video...I like your style! Enjoyed watching.
Thank you so much!
Glad you you liked it!
By chance do you need to use the bracket. I ordered the same gpu but it was missing a piece of the metal brackets. And am not sure if I can just install with out that part
It's a good idea to use an anti-sag bracket.
If you don't have the default one from Gigabyte, purchase and use a different bracket.
Cool job to assemble all these beautiful compartments.
Thank you so much for your support bro👍👍
this is dope: it's exactly my dream build. keep on doing buddy
Oh! Thank you so much💜🖤
@@PC_SNAP love ur dedication of making people happy !!!! Never stop it pls
Finally a build that swapped out the stock CPU bracket. Pro move right there
Oh, thank you so much👍
I used the Intel i7-14700K for the first time, so forcefully used the BCF bracket!
Thanks for the comments, bro💜🖤
Mind-blowing!
This build is absolutely amazing. I hope I can do such a build but with a 4080 super in the next few months too
Thank you so much! I'm glad you liked it👍
Wow, that's a great plan! Hope you complete the awesome build💜🖤
@@PC_SNAP Thanks 🤍
@@PC_SNAP Thanks 🤍
이쁩니다 눈 정화하고 가네요 국내에 이런 퀄리티 영상이 있다니
근데 슬리빙 케이블 정보도 있었으면 좋겠어요!
오호 안녕하세요! 감사합니다~
앞으로 자주 방문해 주세요 :)
bit.ly/46Renwf 슬리빙 케이블 링크입니다. 커넥터도 화이트라 꽤 쓸만해요.
what a high end build
Thank you so much!
Gorgeous....I am building one now.
Absolutely in love with not only the build quality, but the video production quality too. Only problem with the build is the rather noticeable Black PSU.
Thank you so much!
That's right, I don't have a white PSU, unfortunately.
I'll definitely keep that in mind for next time.
Thanks for the great input💜🖤
I had the same curiosity as to why he did that.
Looks great! I am doing an almost identical build, except with a Kraken 280 instead of 360 and 4070 super and i5-13600K. One thing I wanted to ask, do you think it is needed to do the rear exhaust fan? I am hoping for somewhat positive pressure inside to prevent dust from coming in
Thank you so much👍👍
The overall heat from the 4070 Super and 13600K with the Kraken 280 isn't significantly high, so it's pretty fine without the rear exhaust fan. However, the exhaust relies on the radiator, so you could increase the fan speed a bit. Hope this helps!
great video. what is the psu? and if there is other component that ain't in the description can you please tell me thanks.
It's the Seasonic Focus GX-850 Gold!
magnificent build 👏🏼 well done!! I'm hesitant to buy the same air cooler. could you tell me your feelings in terms of noise when you play? thank you in advance
Thank you so much!
I hope you meant an AIO liquid cooler. Overall, I can't say it's quiet like other AIO coolers.
Since there's significant pump noise, it might be better to adjust PWM settings for the cooling fans.
@@PC_SNAP hi, sorry... yes AIO liquid cooler ! Thanks for your feedback
That looks great other than that black aio cable. You would think after providing white tubing and a white cpu block, the could have made the other cables white also.
I had the same thought when building this, it would have been perfect with white connecting cables. Thank you for sharing your great thoughts.💜🖤
What a good video and good quality thats it im buying it :D
Beautiful computer bro!
Always grateful, brother!! 💜🖤
새로나온 nzxt 케이스군요 너무 멋지네요 메인보드 화이트도 깔맞춤되서 하나 맞추고 싶습니다 ㅎ
고퀄영상 만드시느라 고생많으셧어요
하이 성철님! 매번 영상 봐주시고 좋은 의견 주셔서 정말 감사합니다.
늘 건강 유의하세요 :)
I’ve been looking for a long time and decided I’ll get this exact build for the wife. Also, can these be bought at MicroCenter? Thanks buddy! I also love the music. It’s gentleness helps my emotional state collect itself being one again.
Thank you so much!
They're common components, so you should be able to find them there.
Question? A lot of other people use a rgb/fan hub but you use two stock rgb controllers. How does all the fan wires fit motherboard?
yo dude the cables how did you connect the cables for the rgb fans cuz im doing what your doing with the case at least and i cant find any sources showing how to connect them little help
No worries man!
In the NZXT controller, there are three RGB nodes, and each needs to be connected. In this video, two controllers were used, and a total of six nodes were connected. The remaining RGB fans were connected to the motherboard's +5V 3-pin ARGB header. All fans can be controlled through NZXT CAM.
AIO RGB Fans
> Used the RGB controller included with the KRAKEN 360 ELITE.
Rear and Bottoms Fans
> Used the RGB controller included with the F140 RGB CORE DUOE.
Side Front Fans
> Pre-connected with a +5V 3-pin ARGB gender connector and connected into the motherboard header.
Give it a try and if it's still tricky, why don't you contact the NZXT support team?
Hope this helps!
안녕하세요? 그래픽카드, 메모리를 제외하고 동일한 구성으로 작업을 마쳤는데요,
1. 케이스 전면팬3개가 팬은돌아가는데 불이안들어옵니다ㅠㅠ (보드 하단 ARGB에 동일하게 장착했습니다ㅠㅠ)
2. AORUS에도 불이안들어와용ㅠㅠ
3. 갤럭시4070 RGB sync 부착하면 글카 RGB가 안들어옵니다ㅠㅠ
윈도우 설치전이긴한데, 부팅이전에도 그냥 키면 불이 다들어와야하는거 아닌가요??🥺
안녕하세요!
간혹 RGB 동기화 프로그램 전에 메인보드 RGB 관련된 제품들이 OFF 상태인 경우가 있었던 것 같습니다.
기억이 가물 가물하지만 저 역시 이번 빌드 동일한 증상이었던 것 같네요. :)
어떻게 해결이 되었는지 모르겟네요~ 새해 복 많이 받으세요~
nice video😀
Thank you so much!
질문하나만 드리겠습니다. 오늘 배송받고 조립하다가 기존 케이스의 hdd+ hdd- , reset 등의 케이스 컨트롤 케이블이 없어서 보드에 연결을 못하게 되어 있던데요
케이스 파워는 조립완료하면 이상없나요? 싸구려케이스만 쓰다가 큰마음먹고 구매했는데 종전 케이스랑 달라서 여쭤봅니다.
안녕하세요~ 최근 몇년간 출시된 NZXT의 모든 케이스는 통합 IO 커넥터를 사용해서 그냥 메인보드 단자에 꼽으시면 되어요.
케이스를 조립하다보면 +LED -LED하고 PWR 만 있는 제품도 있고, RESET이나 HDD가 없는 케이스도 많아요.
사용에는 당연히 문제가 되지 않고요. 벤치 돌리는 PC는 그냥 전원 PWR만 연결해서 사용할 때도 있습니다.
@@PC_SNAP f pannel 을 보드 소켓에 맞게 꽂으면 되는거군요. 이해했습니다. 늦은시간 답변 감사드립니다.
오...홍 새로 나온 케이스군요! 므찌네요 ㅎㅎ
오호~ 안녕하세요!
넴! NZXT H6 FLOW 케이스입니다.
감성 좋고, 쿨링 좋고, 정말 좋습니다 💜🖤
waiting for black build on that case! 😊
Yo! I'm planning a PC build with the Lian Li AIO for the black version of it, probably early next year.
Please, look forward to it💜🖤
My only issue with this case is missing grommets in the case ,and a reset button.
I personally don't use the reset button, but I absolutely agree with you!
Amazing! where you get those white cables?
Yo! Please, check this link :)
bit.ly/4aDQvyX
Is the h6 flow case already have RGB fan installed?
Yes! three side intakes are installed by default in the RGB version💜🖤
@@PC_SNAP If we buy the non rgb, can we replace it with another fan that has rgb?
Yes you can @@ttsneg6663
@@ttsneg6663yeah
@@ttsneg6663yes as long as it’s 120mm
수냉 쿨러 이미지 GIF 파일 어떤거 쓰셨나요? NZXT CAM 에서 찾아봐도 안보이네요 이미지 파일 다운로드 링크 알려 주실 수 있나요?
안녕하세요~ 아 ㅠ 빌드할때 NZXT CAM 말고 구글링해서 찾아서 사용했는데요. 밑에 다른 구독자에게 찾아보라고 링크를 주었는데, 못찾겠다고 하네요. 죄송해요.
Can you configure all the fans with cam or just the ones connected to the nzxt RGB controllers?
If you use an NZXT motherboard, you can control everything through NZXT CAM. If not, it's necessary to handle the +5V ARGB separately on the motherboard.
I'm planning my first PC build with the black RGB version. Also using the 14700k, but just a RTX 4070. I was wondering if you think the NZXT Kraken 240 AIO would suffice over the 360. I was still planning on doing what you did though with the two 140s in the bottom and the 120 on the back.
Awesome build and i loved your editing!!!
Oh, thank you so much! I'm glad you liked it 👍
The 14700K tends to generate quite a bit of heat, so the NZXT Kraken 240 AIO may not be sufficient. However, it could still work well if you consider aggressively undervolting the CPU or setting a power limit (at least 220-230W) when using the CPU at full load.
While a 360 AIO is the optimal choice, a 240 AIO should suffice for tasks or gaming with a power consumption of around 200W.
Hope this helps💜🖤
@@PC_SNAP you’re the best! Best answer I could’ve hoped for 🙏
I DID have one more tiny question about the NZXT lighting. Did you need to buy one of their rgb fan controllers? Or was the two hubs that came with the intercooler and f140s suffice (I’m PRETTY sure you can manage with two and then daisy chain the last three into a sys fan port on the motherboard??) like I said 😩 I’m a noob.
Ps I’m planning on getting the NZXT usb hub as well just to make sure I’m not using up both usb ports on my motherboard. I actually may not need it at all but 🤷♂️ I’m a noob! 😂
@@TheBTeamOfficial No worries bro!
First, the front NZXT RGB case fan is connected with an ARGB +5V connector cable. However, if you remove the connector, it can be used with the NZXT controller. The NZXT controller can connect three individual nodes to one device!
The two NZXT 140 RGB fans at the bottom are part of the package and include the NZXT controller. Therefore, they can be used simultaneously with the rear NZXT 120 RGB fan.
Additionally, the Kraken RGB version comes with the NZXT controller, so it can be used without any issues.
Therefore, if you use all three NZXT controllers, you can control everything through NZXT CAM. If you want to use only two controllers, you can synchronize the front fans using +5V ARGB (mainboard header) for overall colour matching.
The NZXT Kraken comes with a 2Y USB 2.0 header cable, making it convenient to connect the three NZXT controllers to the motherboard as well. :)
Good Luck💜🖤
@@PC_SNAP Without sounding too dumb here, Did you use three controllers in this build and did you have to buy an extra? I'm pretty sure i'll only get two (one from the 360 kraken and one from the two pack F140s for the bottom of the case) after all is said and done with purchasing.
And thanks so much for the insight on the 2Y USB 2.0 header cable! I think that means i can get rid of the extra NZXT usb 4 to 1 hub off my list. I think the included cables will take care of that.
Got it! In the video, I used two NZXT controllers. One is from the Kraken AIO, and the other is included in the NZXT RGB 2-pack. You just need to connect the front fans to the motherboard's ARGB header!
Damn great video but what are the songs you used in this one?
Thank you so much!
Please, check the link down below!!
shorturl.at/yq4Ys
shorturl.at/fyXL0
What is the black thing that you placed around the CPU. I've been trying to find it for a long time!
Check it out here!
shorturl.at/U9JRb
This build is 🥶🥶🔥!! You may have just inspired me to build one exactly like it since i'm in the market using the same type of hardware, and love the NZXT aesthetic. Curious what custom cables you were using (if any)? Also, i'm a first time builder, and while your video makes it look easy, could you possibly share steps or any gotchas that perhaps your video obviously would never reveal? 🙂 Looking forward to future builds!
Thank you so much!!
I'm glad you liked it👍👍
Check the following link for the cables!
bit.ly/46Renwf
bit.ly/47LHUZd
I'm editing the PC assembly video concisely and excluding unnecessary steps or poorly shot parts. If I include every step, the video will be longer, and there's a high chance it could become tedious.
I'm not a professional in the PC industry and not a full-time creator. About once a month, when PC components are ready, I shoot videos. It's one of the biggest hobbies in my life.
Thank you so much for your valuable opinion! I'll definitely think about it later.💜🖤
thanks, bro! what about that gpu brace, have a link for that as well? @@PC_SNAP
where did you got this NZXT GIF for your Kraken watercooler?
I mainly download the GIF files for my channel videos from giphy.com/
@@PC_SNAP ty
Love NZXT 💜
I also love NZXT a lot, bro💜🖤
I am about to buy this board and wanted to make sure that you got the rgb working with fusion?
Yeah! Memory RGB, motherboard RGB, and graphics card RGB work well with GIGABYTE Fusion.
The NZXT RGB core fans are controlled by NZXT CAM, and the front fan of the H6 FLOW has a +5V header, so it also operates with GIGABYTE Fusion
Hope this helps!
우와 cpu 쿨러에 온도도 표시되고 엄청 이쁘네요!
하이염~ 네넵~ NZXT 크라켄 LCD 화질도 좋고, 엄청 이쁜 것 같아요.
영상 봐주셔서 감사합니당~
where is the gpu cable Extension your using from
It's the cable that directly connects to the PSU!
Refer to the link bit.ly/47LHUZd
Would you mind telling me what ssd you’re using? I’m on my way to creating an exact build with 13700k 4060ti
Sure man! I used the WD Black SN850x. The price is reasonable, and the performance is great ❤
@@PC_SNAP I appreciate the response and good video bro💯
why you removed the pre applyed heat paste on the Kraken?
I removed it to use ARCTIC MX-6 for thermal testing purposes!
@@PC_SNAP I will also remove the pre applyed paste for grizzly hydronaut
Hello, I'm curious about white 12vhpwr cable for gpu,how is that white?
Yo good question!
Please check this link :)
cablemod.com/product-category/12vhpwr/12vhpwr-pci-e-cable/
whats the anti sag thing you put in the case called?
It might be something like this link,
amzn.to/3YlT7NY
hey bro im plannin gon getting the same build does the GPU support 16 pin connector as my psu does
Yo! Graphics cards above RTX 4070 use the 12VHPWR standard, which is a 12-pin connector. If it's a 16-pin connector, it would likely be 8+8 pins, so you can use the included connectors.
안녕하세요 영상 잘 봤습니다 번들 브라켓을 사용하지 않은 이유를 알 수 있을까요?
4070 ti suepr aero 번들 그래픽카드 지지대 안쓰신 이유가 궁금합니다
아~ 화이트 빌드에 맞는 지지대가 있어서 편하게 사용한 것 같네요. 특별한 이유는 없었던 것 같습니다.
What cable extensions did you use?
Check the following link!
bit.ly/46Renwf
bit.ly/47LHUZd
The 12VHPWR cable might be okay for the 4080S, but for the 4090, it's safer to use the cable included with the PSU.
I have the same morherboard and i tried and tried to change the rgb collot on the motherboard but i couldn’t it is stuck on the rainbow puke, can you help me?
Did you use Gigabyte Control Centre?
If not, first install GCC and then install the Gigabyte MB RGB Tool within GCC.
If you want to change the memory RGB, you need to install the Storage Library, and if you are using a Gigabyte graphics card, you also need to install the VGA tool.
Everything is completed, you can control everything through RGB Fusion (which also needs to be installed) for unified control.
Hope this helps :)
I will try that right now, i hope it will solve my problem, thanks so much@@PC_SNAP
It solved my problem, thanks for the help
And now
My bank account looks at me knowing it is inadequate
lol~Oh, please don't tell my story~
Thanks for the comment 💜🖤
Using m2 port between cpu and graphics card in this motherboard didn’t cut the graphics card speed?
During recent benchmark tests, it seems that the M.2 NVMe PCIe lane did not have any noticeable impact on the GPU performance.
Any experience with this?
@@PC_SNAP I’ve seen a few videos where people say not use this port
Got it! If the mainboard GPU and M.2 NVMe share the same PCIe lane via CPU, there may be a potential for performance degradation.
However, for instance, even if there is a downgrade from x16 to x8 in the GPU lane, it is unlikely to have a significant impact I guess.
Thanks for your information:)
Looks amazing! How much was the whole build?
Thank you so much!
I haven't checked the price in detail, but it seems to be around 2700 USD.
Can i use m.2 990 pro with heatsink ot it will be uncoverd ?
The 990 pro is top-notch ever for PCIe 4.0 grade. However, I'd recommend using a heatsink!
Nice Build. Could you share that AIO gif file?
After the build video, I disassembled the PC right away, so I don't remember it exactly.
but I probably downloaded it from this link.
gifer.com/en/7IsD
Thanks a lot💜🖤
I have a question that motherboard is compatible with the rtx 4090 ?
Yeah! It works perfectly without any issues 👍👍
@@PC_SNAP another question i can put 128gb of ram but but both are 6000MHZ each box, there is no problem, right?
Did you buy those Nzxt RGB fan controllers? Or it came with the case?
The case comes with a front RGB fan that uses an ARGB +5V connector.
Therefore, it doesn't include an NZXT controller.
I used the RGB controller included with the F140 RGB CORE and KRAKEN 360 ELITE 💜🖤
그래픽 카드 8pin 마더보드 24pin 슬리빙 케이블 어떤 제품 사용하셨는지 알수 있을까요?
안녕하세요! 댓글 감사드려요.
알리에서 주문한 슬리빙 케이블이고, 링크는 다음을 참고하세요 :)
bit.ly/4aDQvyX
did using the top m.2 slot drop your gpu down to x8 instead of x16?
Not really. Depending on the motherboard, there may be issues with PCI lanes, but it was difficult to notice any real impact.
Is the fan hub included in the case?
No, it's not included. The controller comes with the Kraken AIO and ARGB fans.
Did you use only 2 RGB controllers in total to manage 8 RGB fans?
Three front fans are connected to the mainboard's ARGB +5V, and five fans are controlled by those controllers!
Dose the nzxt fans come with the adapter
Yes, the front fans come with an adapter for the motherboard's +5V ARGB 3-pin connection!
@@PC_SNAP thanks I love this build I'm subbed
what display gif are you using?
I don't remember exactly, but I think I downloaded it from this link.
giphy.com/explore/free-download
Hi! I'll give you one more GIF link.
gifer.com/en/7IsD
@@PC_SNAP hey, doesn't seem like it was the right gif :(
12vhpwr 케이블 어디건가요?
CableMod 케이블입니다. 한국은 서린에서 유통해요. 밑에 링크 참조하세요. 아~ 시소닉 ASUS 호환 케이블입니다.
www.seorinexpress.com/goods/goods_view.php?goodsNo=1000004854
What cable extensions are those for the gpu and mobo?
Hello~ Please check the following link bro!
bit.ly/4aDQvyX for the mobo
bit.ly/47LHUZd for the GPU
I subscribed on chanel, my suggestion is to add air flow in video.
Thank you so much for subscribing and great suggestion!
my exact dream setup you should do a give away
What PSU are you using?
Yo! It's the Seasonic FOCUS GOLD GX-850👍👍
Thank you 😁
Prix stp😊
lol I did almost the exact same build with case / aio / ram but I went with AMD nice build :)
No way, what a coincidence!
The RAM is quite rare, but you made a great choice.
Ah~ The next video is planned for a budget PC build using the 7500F.
Thanks for the comments💜🖤
Total price ?
Not sure but isn't it around 2500 USD?
👍 !!! 👍 !!! 👍 !!!
💜🖤
H6 side panel just feels a little awkward while installing a 360 radiator
Yes! It may look like that because the angle is off.
Thanks for watching the video 💜🖤
where is the vertical mount?????????????????????????????????
Why everyone thinks everyone wants vertical gpu?
Is Intel better than AMD ?
I use Intel for video editing, but AMD for my kids' gaming.
It seems like the advantages vary depending on the purpose.
@@PC_SNAP thanks for replying me, i have a 14700K (i just play games at 1440p) should i return it and grap a 7800x3d instead ? Im still on return window but i lose at least 10% of Price because i opened the packages
nah that intel is a beast if u had a 12thgen then maybe but 14700k will last u 7 years or more @@cuongtang9539
@@cuongtang9539if you get amd when u already have intel cpu you would have to buy a new motherboard
@@cuongtang9539depends, what do you do, gaming or editing?
I can't be the only one who thinks this case look absolutely terrible, right? Love the channel and can't wait to see what awesome builds come next!
Thank you so much! If you actually see the case in person, it looks really good.
Appreciate the comment, and I'll make sure to create some awesome PC build videos.💜🖤
NOOOOO way
They power supply is black !!!
Sorry bro! There was only a black PSU available. Of course, I still don't have it :)
Can u tell me where u got that white gpu cable from?
Dude, check out the link below!
bit.ly/46Renwf
I wanna know too! Please !