HOW TO Desolder a LED | SMD LED Desoldering Tutorial

Поделиться
HTML-код
  • Опубликовано: 30 янв 2025

Комментарии • 45

  • @jaybird99100
    @jaybird99100 10 месяцев назад +3

    What would be the method if you wanted to attempt putting it back. I have one of those little LED’s that broke off its solder on a LED fog light for my vehicle. I have a couple led strips I could remove a LED from to attempt to add in place of the broken one but how would you suggest doing it?

    • @isaacastudillo9764
      @isaacastudillo9764 Месяц назад

      If you’re still wondering write me back. Bought a tundra recently and didn’t know the guy that owned it before me broke off the led so the light wouldn’t show. I’m going to be fixing it soon

  • @XtianApi
    @XtianApi Год назад

    Wow, simple but effective

  • @rayneaustephane2757
    @rayneaustephane2757 11 месяцев назад

    bonjour et merci pour votres tres bonne technique de déssoudage de SMD !
    je me suis toujours demandé quel puissance il fallait pour alimenter une led SMD ?
    j'ai un petit projet pour une maquette et j'aurai besoin de quelque smd pour la faire !
    leurs faut-ils une resistance, aussi, s'il vous plait ?
    merci encore.

    • @TheLabOtomy
      @TheLabOtomy  11 месяцев назад

      Cela depend du nombre de LEDs que le paquet SMD contient. Ils ont commence par une LED par SMD, mais il y en a avec maintenant 4, 6 et plus. Chaque LED necessite 3V (si en serie) en il faut limiter le courant (si cela n'est pas fait sur le circuit) ou la/les LED(s) ne limite(nt) rien et va/vont griller

  • @rasmasyean
    @rasmasyean Год назад

    Can you put it back using the same method?

    • @TheLabOtomy
      @TheLabOtomy  Год назад

      I would not do it since you risk shorting the 2 pads

  • @blknslvrgsxr
    @blknslvrgsxr 2 месяца назад

    I've got some map light LED's in my vehicle that I'd like to have replaced on a circuit board in my rear view mirror. I've already attempted to do this, but don't have the proper tools to do it and ruined the circuit board. Id like to take it somewhere to have it done properly but not sure what kind of company I should look at to do the work. Any idea on what type of service/company I should be looking up to have them do this for me?

    • @TheLabOtomy
      @TheLabOtomy  2 месяца назад +1

      Sorry, unable to advice on that one

  • @truchal
    @truchal 4 месяца назад

    Geile Sache !!!

  • @olandesevolante3684
    @olandesevolante3684 Час назад

    Gli stessi led 5730, dopo dissaldati, non venivano via perché incollati al circuito. Ho dovuto distruggerli rischiando di danneggiare le piste. 😢

  • @agustinc6514
    @agustinc6514 9 месяцев назад

    Buen vided justo lo que andaba buscardo gracias

  • @aaddlla6899
    @aaddlla6899 Год назад

    Brother why use that metal piece. Why not direct contact btw chip and solder or lighter etc?

    • @TheLabOtomy
      @TheLabOtomy  Год назад +1

      To have a more broad heat distribution. If localised may only weaken one part of the solder, not all of it

  • @tunkunrunk
    @tunkunrunk 4 месяца назад

    can't we use desoldering hot aIr gun instead ?

  • @rayneaustephane2757
    @rayneaustephane2757 11 месяцев назад

    PS: 3 volts ou du 12 volts ? merci.

    • @TheLabOtomy
      @TheLabOtomy  11 месяцев назад

      J'ai fait un tuto sur l'alimentatio de LED precedemment, peut-etre que cela aidera. Voir ruclips.net/video/h6-EnP5ArSo/видео.html

  • @myfavoritegift
    @myfavoritegift Год назад

    thank you

  • @Martin-cs8ty
    @Martin-cs8ty Год назад

    buena idea maestro

  • @anyonecanmakeit718
    @anyonecanmakeit718 2 года назад

    Yes it works just keep heating for 90 secs and boom all led will start falling off.👍

  • @rezakikin-fi2fm
    @rezakikin-fi2fm 9 месяцев назад

    gosong apa tidak itu di pcb belakang..

  • @Z-Ack
    @Z-Ack 12 дней назад

    Flux.., and here i was using mayonnaise.. But a chip aint a chip without the tangy strip of miracle whip..

  • @vkgamingplatform7247
    @vkgamingplatform7247 Год назад

    I used Blade to remove 8/10 working led

  • @vladimirpena8171
    @vladimirpena8171 2 года назад +2

    Excelente

  • @RamsBejaoui
    @RamsBejaoui 3 месяца назад

    ما هو الساءل ابي استعملته

  • @XMSTeamz
    @XMSTeamz 3 года назад

    Excellent xD

  • @EricGranata
    @EricGranata 3 года назад

    smol 💡

  • @bodziogaming3884
    @bodziogaming3884 Год назад

    tego nie da sie wlutować taakiej diody to jest nie moźliwe sam prrubowałem

  • @hasanbasalan5782
    @hasanbasalan5782 2 года назад

    Hallo kannst du mir ein led auch löten

  • @dmitriykoltunov4261
    @dmitriykoltunov4261 11 месяцев назад

    Omg. Bro needs a heat gun

    • @Z-Ack
      @Z-Ack 12 дней назад

      Go on and try it with a heat gun. Smd leds are brittle melty plastic.. they will turn into a puddle quick if you overheat the area..

  • @PaladinJenkis
    @PaladinJenkis Год назад +1

    That is some caveman shit right there