Thank you, great idea , now I will try to replicate it for my bike, Now I'm using a timer XY-LJ02 setting at 60ms with relè and a hall sensor, magnet etc etc , it works but the neodymium magnet attracts metal dust ...
@@guser210 I create bypass "Y" connector ignition coil, One head connect to ignition coil (two wire i use only black wire) and other head connect to rele on Timer XY-LJ02,and 3th connector to engine wiring Hall sensor a3144 and 3d print support installed proximity gear lever, but the neodimio magnet pasted epoxy glue on gear lever, It attracts dust and the play between sensor and magnet and only 1 millimeter, after 20 km I find myself with the magnet already full of dust and falsifies the operation. the relay is connected in NC mode, I switch it off and use the clutch normally, when the dust False the signal. 👍👍
Ive made my Quickshifter sensor myself aswell, however most ecu's need a closed circuit as input signal. Ive used a switch in my design so it closes on shifting.
Tygo ah I see your bike is bit different, usually big bike ACU’s will give errors if you mod any of the inputs, I saw your video very cool, now you just to to mod it to rev on downshift.
@@guser210 the sensor i made actually only is a push type sensor, that is because I have a carbureted bike.(rev on downshift is impossible this way) I do want to know tho how you would use yours, so how do you connect the quickshifter sensor(which puts out a voltage) to the bike(which cuts the ignition or injectors)?
Tygo cool, I’ll do a series of videos on the entire unit, I tried cutting power, fuel, and spark, but the one that seems to work best is delaying spark since you can smooth it out as much as you want.
Hello friend, very good video. What type of magnet do you use and where can you get it already drilled? Otherwise, how did you make the hole? The rest is aluminum?
Hello there, you can get the magnet from apexmagnets.com the part number is M121418R, the pull force is 3lb and yes the rest of the components are made of Alumnium
Trung Nguyen I have been using this sensor for the last 4 years, this video is just a demo to help people with their own since the sensor seems to be the difficult part
It won’t shift unless you use the clutch the normal way. Obviously it depends on how much redundancy you want to add. It all depends on the code you write, let’s say you write faulty code and you forget to release the coil for some reason and you engage the next coil... you will blow a fuse and the bike will shutoff, or if your timing is off and end up releasing the coil late... the cylinder won’t fire and the bike will backfire, if you do enough for those you will shoot a huge flame, looks awesome at night. If you release the coil early nothing happens because the ecu won’t release it and will take over
Do you know anyone who makes a sensor such as this with a 0-5v range in a washer style configuration? Im needing one for a car and have come up empty handed. Something similar to the healtech quickshifter sensor, but 3 wire so I can hook it up to my cars ecu.
@@guser210 I am refering to this one. www.dynojet.com/quick-shifter-power-commander-v-linear-shift-sensor-push-type/ So instead of a fix point inside, it has a rod that moves up and down
@@guser210 For some reason I think it might be magnetic. My rod pulled out while I was fixing my bracket to install it. In the process it seems to have damaged to actuator and trying to fix it now
Truly amazing piece of work and thanks for sharing it! Is it possible to buy the kit from you - I would like to adopt it in my own racing motorcycle datalogger / dashboard that I'm building (ruclips.net/video/epZFIy9R4gw/видео.html) and would really appreciate your help in providing those parts! I also have many other questions re adopting your further components (full quickshifter assembly) let me know if to put them under comments or via other channel?
Thank you for a very Good simpel explenation of how it works👍😀
Thank you, great idea , now I will try to replicate it for my bike,
Now I'm using a timer XY-LJ02 setting at 60ms with relè and a hall sensor, magnet etc etc , it works but the neodymium magnet attracts metal dust ...
orlando what exactly are you going to do? Kill power to the engine and then let it jump start on its on?
@@guser210 I create bypass "Y" connector ignition coil,
One head connect to ignition coil (two wire i use only black wire) and other head connect to rele on Timer XY-LJ02,and 3th connector to engine wiring
Hall sensor a3144 and 3d print support installed proximity gear lever, but the neodimio magnet pasted epoxy glue on gear lever, It attracts dust and the play between sensor and magnet and only 1 millimeter, after 20 km I find myself with the magnet already full of dust and falsifies the operation.
the relay is connected in NC mode, I switch it off and use the clutch normally, when the dust False the signal.
👍👍
@@orlando8193 try filling that 1mm space with some non magnetic material like plastic.
Ive made my Quickshifter sensor myself aswell, however most ecu's need a closed circuit as input signal. Ive used a switch in my design so it closes on shifting.
Tygo do you get any f1 errors when you shift?
@@guser210 What do you mean with f1 error? I do have a video about my quickshifter on my channel.
Tygo ah I see your bike is bit different, usually big bike ACU’s will give errors if you mod any of the inputs, I saw your video very cool, now you just to to mod it to rev on downshift.
@@guser210 the sensor i made actually only is a push type sensor, that is because I have a carbureted bike.(rev on downshift is impossible this way) I do want to know tho how you would use yours, so how do you connect the quickshifter sensor(which puts out a voltage) to the bike(which cuts the ignition or injectors)?
Tygo cool, I’ll do a series of videos on the entire unit, I tried cutting power, fuel, and spark, but the one that seems to work best is delaying spark since you can smooth it out as much as you want.
Hello friend, very good video. What type of magnet do you use and where can you get it already drilled? Otherwise, how did you make the hole? The rest is aluminum?
Hello there, you can get the magnet from apexmagnets.com the part number is M121418R, the pull force is 3lb and yes the rest of the components are made of Alumnium
Hello. Thank you for sharing, how can i buy the sensor module in your video? Tks
Trung Nguyen you can buy it from me I guess
Hopefully u will finish soon. Do u have email?
Trung Nguyen I have been using this sensor for the last 4 years, this video is just a demo to help people with their own since the sensor seems to be the difficult part
what is the worst case scenario if diy quickshifter does not work at high rpm's?
It won’t shift unless you use the clutch the normal way. Obviously it depends on how much redundancy you want to add. It all depends on the code you write, let’s say you write faulty code and you forget to release the coil for some reason and you engage the next coil... you will blow a fuse and the bike will shutoff, or if your timing is off and end up releasing the coil late... the cylinder won’t fire and the bike will backfire, if you do enough for those you will shoot a huge flame, looks awesome at night. If you release the coil early nothing happens because the ecu won’t release it and will take over
Do you know anyone who makes a sensor such as this with a 0-5v range in a washer style configuration? Im needing one for a car and have come up empty handed. Something similar to the healtech quickshifter sensor, but 3 wire so I can hook it up to my cars ecu.
Nope other than me, the new version uses spring washers and 0-5 volt range or 0-3
Let’s talk discord.gg/pByahDupYP
DRV5056 vietnam not sell. Can change DRV5056 to hall effect 3144?Yes?
Dương Cao Quốc Huy I don’t think it will, you need to look for a linear Hall effect
@@guser210 yes. You can share me Your Fb. I have project using rpm and QS
Hi there, do how have any knowledge regarding push type of sensors? Do they also work with a magnet?
This sensor is both push and pull but I am not sure how others work
@@guser210 I am refering to this one. www.dynojet.com/quick-shifter-power-commander-v-linear-shift-sensor-push-type/
So instead of a fix point inside, it has a rod that moves up and down
@@michaelo.8276 I am not sure my guess is that they have a load cell
@@guser210 For some reason I think it might be magnetic. My rod pulled out while I was fixing my bracket to install it. In the process it seems to have damaged to actuator and trying to fix it now
@@michaelo.8276 you should be able to see if is magnetic by simply putting a small piece of metal wire close to it.
Hello, Can you make a short video to show how the electronics are made? And by the way, how much is the input voltage? 5V?
Duy Tùng Phạm sure, I’ll do one this weekend
Duy Tùng Phạm yes is 5 volts but it works from 3 volts up to 30 volts.
@@guser210 thank you sir, I've been looking for the sensor working principle for so long until I found your videos, they're very helpful.
Duy Tùng Phạm video is being processed, should be ready in a few minutes
@@guser210 that's fantastic sir, I've been through the weekend waiting for your video.
what is the name of the component with the cable
angel eye that’s a DRV5056
Link pembelian tuas qs??
Can i buy this sensor?
Bisa order 1
I’m guessing you want to buy one?
Hey what's the reference of your sensor? Have you a link please?
The electronic part? DRV5056 you can get it from digikey or mouser.com
@@guser210 and the ring?
@@ewanguilleret7781 the o-ring is 1173N202 you can get that from mcmaster.com
@@guser210 thanks 🙏🏻
@@guser210 and finilly what is the steel ring reference link to the sensor?
How much?? Can u ship to malaysian??
I can send you the kit for you to build, I’ll look to see what it costs
@@guser210 okay.. update me thanks..
Hello.. how much it cost me sir??
Interested
using inox???
Dương Cao Quốc Huy what is inox?
@@guser210 body sensor
@@buiminhnhut7294 thank you so much, is all aluminum
The entire unit is made of aluminum, it can’t be attracted to magnet.
nhôm
Truly amazing piece of work and thanks for sharing it! Is it possible to buy the kit from you - I would like to adopt it in my own racing motorcycle datalogger / dashboard that I'm building (ruclips.net/video/epZFIy9R4gw/видео.html) and would really appreciate your help in providing those parts! I also have many other questions re adopting your further components (full quickshifter assembly) let me know if to put them under comments or via other channel?
Hello can i buy it?
Har tarto do you want the kit so you can assemble it yourself ?
@@guser210 hello, also interested of buying one
@@7gumball are here in the US?
@@guser210 Im in Canada
@@7gumball just out of curiosity what are you going to use this on?
I know the video is 4 years ago,but can you give me you contact,email or number whatever?
There is a discord link in the description if you have a question.