@@aarons7135it varies state to state. In WA state, once a vehicle is 25 years old it no longer has to meet any exhaust laws. I can cut out everything from the header back if I want to. I ran a V6 Ranger on open headers for 3 months straight lol
Sweet! Y’all made a tire carrier that will swing into oncoming traffic! 🤘Cause I’ve never seen one accidentally not get completely closed, practical joker undo the latch, or just the latch break…. 🙄😂
Just so you guys know, all 4L60E and 4L80E cases are 2 wheel drive with a T-case adaptor, and the 80E always has both speed sensor locations in the case. Its the output shaft and in the 80E the rear bushing lube that are different.
That's a nice rig. And I get the SBC vs BBC for the front end weight, and maybe traction. Can you four-corner weigh the truck for some data? That would be helpful as well. Thx
Awesome Build guys sweet send it my way 😀 😎 it would make me a great hunting and fishing Rig for sure 👍 thanks for sharing The Build !! The Vermonter BS
Awsome channel. I hope to have editing and content as good as yours eventually. I try for mostly squarebody content but get some semi truck stuff in there.
Great build and I can't wait until it's done and on YT. I am concerned about that exhaust. Maybe I've just inhaled too much of that stuff and am too worried about that.
GOOD IDEA to swap out that 700r4 for the 4l80. On my channel, I put a 4l80e in my 6.5 turbo suburban, and it felt like I picked up 50hp! And I don't have to worry about my "built" 700r4 stranding me when towing a 7000lb trailer (which totally sucked when it happened). FWIW that steering column could have been fixed by tightening just a couple of screws inside.
@@moto_rad My 6.5 diesel is out of a 2000 Hummer. 1992 was the first year for the 6.5 diesel, and the 4l60e did not come out until 1993. A 6.5/700r4 is a one year wonder for 1992.
You've confused the 3 stick transfer case. As you have it set up you will NOT be able to do FWD only. That's a completely different setup on the T case. You'll be able to do RWD low using the 1 gear reduction. But NOT FWD only as stated
I was wondering what type of transfer case lets you disconnect the rear axle and have the front connected. It makes more sense that it’s set up like an old jeep with the addition of a second low range.
I always wondered something with these seats when you take out that old nasty chairs and bench seats and stuff why don't you just go to a junkyard and use the nice seats out of a later model car like I'm sure on some of them some of the both holes would line up exactly but it seems like it would be way more comfortable work better and not be too much of a hassle because I know I've seen at least some of the old 90s broncos that guys took like the King ranch seats out of a King ranch F-150 and put in it
@@lordfever5b.e.83 you don't know what or where someone making a comment has been or gone through.....I was on the streets dinking and drugging for 16 years and pulled my crap together and sobered and cleaned up......I benn there, been through it and changed.....just because someone is making jokes or being funny does not mean they're "making fun" of the homeless and drug situations in Portland or anywhere else!!!!!
@Loui Arnold It takes a change in area, getting away from a place or situation that allows that individual to live that way will will actually help that person straighten up their lifestyle, I actually knew people that moved to Portland because they knew it was tolerated....best thing I ever did was move back to GA to where it's almost impossible to make a lifestyle living that way......
Good I'm glad your almost done with Unbreakable, then you can repeat on my 99' 2500! It already has 4L80 trans. Ha ha would be nice to a awesome truck like Unbreakable!!!!!
Why dump all that money into a custom setup just to half ass the cooling fan? I guess they couldn't get a sponsor to donate a proper electric fan with a shroud so they just zip tied it to the radiator.
Building off-road vehicles just isn't your thing. This thing it 6inches to tall, way to narrow and on way to small a tire. And to top it off "unbreakable" broke a trackbar mount or bar in the rear your first time out. You could see it shifted 6inches
So, the main thing in the video is "we put three shifters in a Chevy" and then you do not show anything about installing the shifters. You don't show the floor being cut. You don't show the shifters being test fit; in fact, you filmed while during that, from an angle you could not see it from. You don't show painting them. You don't show installing them. I'm calling BS. So, who REALLY installed them for you?
Slammed trucks are so 2021. Slammed gear ratios are going to be hot for 2022, high gear up front, low in the back. Going get all the strong independent women with that one
Awesome! The world is Suburban crazy right now, perfect timing!
You guys in powernation doing best content I ever seen.
Best power nation team and show thanks guys
For a Chevy. This thing is bad ass
I'm really going to love seeing this hit the road! Great build guys.
Liked gear ratios explained....
Can't wait till the Suburban to touch fresh dirt trails.
I appreciate the fact that you chose to use rachets and wrenches most of the time.
That is awesome you guys do a wonderful job I've always wanted one of those
I’m thinking the exhaust exiting right underneath the passenger compartment, especially with a carpet delete, not that great an idea.
If it had lizardskin sprayed in the cab, line-X’ed undercarriage, boom mat, and a rubber carpet replacement, and those dumps wouldn’t be an issue.
Also not legal for street vehicle for exhaust exit under passenger compartment.
@@aarons7135 each state is different . Some states it’s ok others not so much
@@aarons7135it varies state to state. In WA state, once a vehicle is 25 years old it no longer has to meet any exhaust laws. I can cut out everything from the header back if I want to. I ran a V6 Ranger on open headers for 3 months straight lol
This my new favorite show of all time!
Brandon would be a brother of mine fr
Been looking forward to this episode for too long!
You guys make a good team
Can’t wait for the drive!!!!!!
Sweet! Y’all made a tire carrier that will swing into oncoming traffic! 🤘Cause I’ve never seen one accidentally not get completely closed, practical joker undo the latch, or just the latch break…. 🙄😂
Just so you guys know, all 4L60E and 4L80E cases are 2 wheel drive with a T-case adaptor, and the 80E always has both speed sensor locations in the case. Its the output shaft and in the 80E the rear bushing lube that are different.
That exhaust exiting under the passenger area is a recipe for asphyxiation... 🤔
Knicked it out of the park with the new hosts and show!
Love these guys. Absolutely way better than carcass.. those guys ruin everything they touch
Carcass is garbage. Not even on the same level. I miss Tracy and Joe...
That's a nice rig. And I get the SBC vs BBC for the front end weight, and maybe traction. Can you four-corner weigh the truck for some data? That would be helpful as well. Thx
You're going to have fun getting that jerry can out of that carrier when it's full! Much love from Fate Texas!
These guys are going crazy with camera tricks eating the cricket😂
Awesome Build guys sweet send it my way 😀 😎 it would make me a great hunting and fishing Rig for sure 👍 thanks for sharing
The Build !!
The Vermonter BS
Awsome channel. I hope to have editing and content as good as yours eventually. I try for mostly squarebody content but get some semi truck stuff in there.
Wow. Shameless advertising a bit, huh? 😂
Love the BURBAN, had to sub
I just hauled one just like this in for scrap 😃👍
Great build and I can't wait until it's done and on YT. I am concerned about that exhaust. Maybe I've just inhaled too much of that stuff and am too worried about that.
i love those kc lites on the roof rack which ones are they?
Gravity pro
GOOD IDEA to swap out that 700r4 for the 4l80. On my channel, I put a 4l80e in my 6.5 turbo suburban, and it felt like I picked up 50hp! And I don't have to worry about my "built" 700r4 stranding me when towing a 7000lb trailer (which totally sucked when it happened). FWIW that steering column could have been fixed by tightening just a couple of screws inside.
Im not aware of a 6.5 ever coming with a 700r4
@@moto_rad My 6.5 diesel is out of a 2000 Hummer. 1992 was the first year for the 6.5 diesel, and the 4l60e did not come out until 1993. A 6.5/700r4 is a one year wonder for 1992.
@@CrankAddict my 95 factory 6.5td suburban has a 4l80e
Ready to tow 10K lbs!
This series is about to make me do something stupid and buy that 454 Suburban I've been eyeing out recently...
More updates on the Trash hawk!!! Please 🙏🙏🙏
What did the front bench seat come out of? And did you have to swap the mounting brackets off the old seats?
Did that man just eat a cricket.....and not share?
"Cricket" LOL
That dude is a trip
need to get a EXTREME DUTY KINETIC ENERGRY ROPE
Cool!!!!
Did they put any rubber under the radiator brackets?
You've confused the 3 stick transfer case. As you have it set up you will NOT be able to do FWD only. That's a completely different setup on the T case. You'll be able to do RWD low using the 1 gear reduction. But NOT FWD only as stated
I was wondering what type of transfer case lets you disconnect the rear axle and have the front connected. It makes more sense that it’s set up like an old jeep with the addition of a second low range.
Good job bos
why so many lights? 16 forward facing? think that's enough?
I always wondered something with these seats when you take out that old nasty chairs and bench seats and stuff why don't you just go to a junkyard and use the nice seats out of a later model car like I'm sure on some of them some of the both holes would line up exactly but it seems like it would be way more comfortable work better and not be too much of a hassle because I know I've seen at least some of the old 90s broncos that guys took like the King ranch seats out of a King ranch F-150 and put in it
What range box is that? Make? Part number?
You probably could use a kinetic tow rope and watch Matts off road recovery channel.
bruh this guy eats a chunk of dirt first and now a cricket wtf lol
No one thought about using bed liner as floor liner/sound dampener..or cleaning up the door panels inside..??
I am really confused as to why you did not build the engine while it was outside of the truck???
Where is all the transmission related info?
That engine bay is so large You can fit all of Portland's homeless problem in it.
Well maybe, if you could stand them up straight......😁😁
Don't make fun of the homeless people have problems
@@lordfever5b.e.83 you don't know what or where someone making a comment has been or gone through.....I was on the streets dinking and drugging for 16 years and pulled my crap together and sobered and cleaned up......I benn there, been through it and changed.....just because someone is making jokes or being funny does not mean they're "making fun" of the homeless and drug situations in Portland or anywhere else!!!!!
@Loui Arnold
It takes a change in area, getting away from a place or situation that allows that individual to live that way will will actually help that person straighten up their lifestyle, I actually knew people that moved to Portland because they knew it was tolerated....best thing I ever did was move back to GA to where it's almost impossible to make a lifestyle living that way......
Portland has gone down hill
Sweet
basically it can do 70 mph in 4x4 fwd or rwd???
Ain’t no way my mans ate that cricket
Got an add for an cam shaft.
Good I'm glad your almost done with Unbreakable, then you can repeat on my 99' 2500! It already has 4L80 trans. Ha ha would be nice to a awesome truck like Unbreakable!!!!!
Uhhhh fan shroud anyone...?
The exhaust turndowns suck. A high rear wheel arch exit would have been cool...
straight out the back or side exit before the rear tires would be better for this rig
I think you Underestimated its size. I think bigger tires are needed.
It must be fun to have all the money to build any thing you like.!!!!
hi guys...love your show except...please reexamine the need for the loud, jarring background music. Im a regular viewer otherwise.
👍👍
Why dump all that money into a custom setup just to half ass the cooling fan? I guess they couldn't get a sponsor to donate a proper electric fan with a shroud so they just zip tied it to the radiator.
Do you guys work in Nashville and if so how much would a restoration cost? Ballpark. 91 C1500 short bed
Grossing out over the interior but eats a cricket?
that fan and radiator combo is horribly inefficient i mean you could fit duals with a shroud on that monster or just a single larger fan with shroud.
Being a tall guy the bench seat in the front sucks. Let's hope a short guy is not driving lol.
I'd hate to drive very far without ear plugs it's going to be loud need to run that exhaust rest of the way out
Anyone know if the wilwood brake master fits obs chevy 88-98
Building off-road vehicles just isn't your thing. This thing it 6inches to tall, way to narrow and on way to small a tire. And to top it off "unbreakable" broke a trackbar mount or bar in the rear your first time out. You could see it shifted 6inches
Needs bigger tires.
Cheapskates ! You could have at least sprayed bed liner on the floor .
Whatever happens to all these project vehicles anyway. How does a guy get in line?
A manual transmission would be better.
So, the main thing in the video is "we put three shifters in a Chevy" and then you do not show anything about installing the shifters. You don't show the floor being cut. You don't show the shifters being test fit; in fact, you filmed while during that, from an angle you could not see it from. You don't show painting them. You don't show installing them. I'm calling BS. So, who REALLY installed them for you?
😁👍👌✌🖖😎
Wen are you going to sell it to me
Slammed trucks are so 2021. Slammed gear ratios are going to be hot for 2022, high gear up front, low in the back. Going get all the strong independent women with that one
Guys, send me such a car to Ukraine, I need it.
1st
Wish I had a supplier to get free parts for my truck. 🥲