Was changing bearings on my slash which is a frequent maintenance job here in Canada during the looooooong winters of snow bashing. I had a hex nut grub screw that was locktighted and could not get it from the plastic part which it was in physical contact with, So what i did to get it off basically boiled the whole hub carrier, hex nut, drive shaft part, was not hot enough to damage the plastic but I was able to get the screw loose and finish changing over the bearings. So boiling water can be a way to deal with locktite, who knew
Use naptha to dissolve/dilute the silicone oil. I use a small container with naptha in it and scrub the gears and inside of the cup with a tooth brush. Once you get the bulk of it out, dry parts with a towel, then a blast of air and it's ready to go in a couple minutes vs waiting for the heavy oil to drain out on it's own. This becomes a lot better to do especially once you get over 50K/100K/500K oil in there as that stuff takes forever to drain on it's own. I'm currently running 100k/500k/100k in my outcast diffs and really like it. Enough give to absorb shock on landings, but not so much that diffs unload constantly. Watching you take that center diff out by removing the 2 screws on top of the cage, then laying down the cage sides made me realize how stupid I am for not doing the same. Getting those stupid long pins out is a PITA when the esc/servo is in the way. 20 years in the hobby and still learning!
Just so you know, almost all of the grub screws, etc. from the factory are threadlocked like that, sometimes there is so much, that things like your outdrive cups, and the axle hubs get welded to the parts they are attached to, and like you are doing just add some heat (when I had to remove my hex from the hub, that is exactly what I found, but because it is in plastic, I couldn't use a torch like that, I had to just hold a soldering iron in there to breakup the threadlock). For when you eventually get to them.
I was waiting for the Servo wire in mount surprise! I had same reaction.. makes it a bit annoying to upgrade. Wire routes thru servo mount, under esc tray clips, under driveshaft.. and into Rx box. There must be a simpler way.
Get these for the steering 6x10x3mm Rubber Sealed Ball Bearing pack off 10x for the Kraton and notorious it improved my steering the original ones are bushes only £6.65 and your have 2x spare
Kev when you said it was ready do go, I don’t know if you meant that minute, but lock tight needs 24 hours to cure, or else it’s really bad for the pinion.
Kevin, love your shop man! Lot of hard work I'm sure but it looks so organized and clean, sign of an efficient shop in my opinion. Enjoy and respect all your vids and passion to share. Peace, Wheelchair John in Idaho :)
I bought my ruslter 4x4 by selling stuff on eBay and I am selling more right now to get my next RC, I just started to mess around with eBay to make money for RCs since I don't have a lot of extra money in my regular job. I'm gonna have to check your course out for some tips.
Jeroen Engelgeer have one that you recommend? New to this hobbie and I need to do my center diff also. Don’t have the tools needed Incase I run into this same problem not able to get things out
Isnt it the other way around on the gearing? High speed is less torque and acceleration but higher topspeed. If you want to flip mid air it is the acceleration or brake on the wheels that makes the car rotate? Like on a bicycle, trying to do a wheelie on a higher gear is way harder then a lower gear.
Mate I'm not sure it's your thing to much but an idea for a video the buggie jumps and traction with and without the wing. Just interested to see the difference is
I work in a rc shop and its been a long time since ive had an rc car and im about to pick up a 6s notorious. I am looking for a good bit of upgrades to make it bullet proof and this video went a long way with helping but theres a few more i want to do as well so thank you for all the help and my boss knows you for a good ways back. Said you used to go in his dads shop all the time
I need to find a way to replace/rebuild the front bumper and rear wing, both pieces that snapped off after only jumping it 4-5 times total... Was so hoping this video would have that since they're clearly the two parts on the car that break the most (both replacement parts are out of stock for the next 4 months) Im thinking about fabricating a bumper piece out of sheet metal, but I can't think of a way to fix the wing. ☹
Gosh ya make that look so easy. I’m new to this and need to do my center diffs but affraid I won’t be able to get it done. No torch pen. Where ya get that thing
I'm starting to get interested in the Arma trucks, I like the body's look and if it holds up to your skate park of doom I might have to get one, good video
really like the new business plug! wasnt a big fan of the other one was kinda a little business like but this one is very good keep up the good work!! ps i am thinking of starting a rc channel myself let me know what you think!
Kevin you should be using 1,000,000 weight center diff oil in all of the Arrma rigs. I have used 500,000 before and still thin after it warms up. Great videos!!!!
Don’t worry bout those people kev i cant even afford a cheap Rn car let alone my dream an xmaxx. Guess time and patients is all it takes cause begging isn’t gonna get u nowhere!
oh and on my talion and my dads serpent gt i put 1million in my center can it works really good and he put 20 million in his and it is like rubber so its really good so i would recommend it.
101 about gearing taller gear does not mean better bashing you putting more strain on the motor then you put thicker gear lube is even more strain on the motor and going to make the motor hotter the esc works harder and get hotter faster taller gear smaller tires small gear bigger tires :/
Early sooooo, SUBSCRIBE!!!
Was changing bearings on my slash which is a frequent maintenance job here in Canada during the looooooong winters of snow bashing. I had a hex nut grub screw that was locktighted and could not get it from the plastic part which it was in physical contact with, So what i did to get it off basically boiled the whole hub carrier, hex nut, drive shaft part, was not hot enough to damage the plastic but I was able to get the screw loose and finish changing over the bearings. So boiling water can be a way to deal with locktite, who knew
Use naptha to dissolve/dilute the silicone oil. I use a small container with naptha in it and scrub the gears and inside of the cup with a tooth brush. Once you get the bulk of it out, dry parts with a towel, then a blast of air and it's ready to go in a couple minutes vs waiting for the heavy oil to drain out on it's own. This becomes a lot better to do especially once you get over 50K/100K/500K oil in there as that stuff takes forever to drain on it's own. I'm currently running 100k/500k/100k in my outcast diffs and really like it. Enough give to absorb shock on landings, but not so much that diffs unload constantly.
Watching you take that center diff out by removing the 2 screws on top of the cage, then laying down the cage sides made me realize how stupid I am for not doing the same. Getting those stupid long pins out is a PITA when the esc/servo is in the way. 20 years in the hobby and still learning!
Just so you know, almost all of the grub screws, etc. from the factory are threadlocked like that, sometimes there is so much, that things like your outdrive cups, and the axle hubs get welded to the parts they are attached to, and like you are doing just add some heat (when I had to remove my hex from the hub, that is exactly what I found, but because it is in plastic, I couldn't use a torch like that, I had to just hold a soldering iron in there to breakup the threadlock). For when you eventually get to them.
@Abradolf Lincler I do, it's just when I'm working around plastic, I want something a little more surgical.
I was waiting for the Servo wire in mount surprise! I had same reaction.. makes it a bit annoying to upgrade. Wire routes thru servo mount, under esc tray clips, under driveshaft.. and into Rx box. There must be a simpler way.
Yes there is, when you upgrade it just stick it to rx box and roll cable in it :)
Im liking the self plug intro hourglass timer Kev
Give a man a fish he eats for a day, teach a man to fish he has to buy equipment
Thanks Kev for making the eBay course free I have already started
The aluminium brace is always a good idea ;)
I think it looks cooler with the scratches on the body, makes it look worn and with a 1950s based truck body it suits it really well
I am learning SO much from your videos. Thank you!
Get these for the steering 6x10x3mm Rubber Sealed Ball Bearing pack off 10x for the Kraton and notorious it improved my steering the original ones are bushes only £6.65 and your have 2x spare
Kev when you said it was ready do go, I don’t know if you meant that minute, but lock tight needs 24 hours to cure, or else it’s really bad for the pinion.
Hot racing makes a ton of aluminum parts for these as well as the kraton 6s
Kevin, love your shop man! Lot of hard work I'm sure but it looks so organized and clean, sign of an efficient shop in my opinion. Enjoy and respect all your vids and passion to share. Peace, Wheelchair John in Idaho :)
Because of your channel I wished a real rc car for christmas present.
I bought my ruslter 4x4 by selling stuff on eBay and I am selling more right now to get my next RC, I just started to mess around with eBay to make money for RCs since I don't have a lot of extra money in my regular job. I'm gonna have to check your course out for some tips.
Try heating things up with a soldering iron, less likely to burn other things.
Jeroen Engelgeer have one that you recommend? New to this hobbie and I need to do my center diff also. Don’t have the tools needed Incase I run into this same problem not able to get things out
@@xampleman Any soldering iron will do. Only touch the bolt that is stuck.
The new notorious has the center brace and a upgraded servo arm.
Isnt it the other way around on the gearing?
High speed is less torque and acceleration but higher topspeed.
If you want to flip mid air it is the acceleration or brake on the wheels that makes the car rotate?
Like on a bicycle, trying to do a wheelie on a higher gear is way harder then a lower gear.
Great Video man love the Time laps your getting much better at Video Editing. Great Job man Can't wait for the next one!
Mate I'm not sure it's your thing to much but an idea for a video the buggie jumps and traction with and without the wing. Just interested to see the difference is
I work in a rc shop and its been a long time since ive had an rc car and im about to pick up a 6s notorious. I am looking for a good bit of upgrades to make it bullet proof and this video went a long way with helping but theres a few more i want to do as well so thank you for all the help and my boss knows you for a good ways back. Said you used to go in his dads shop all the time
I love the Notorious! Definitely gonna be my next bashing RC!
Interested to see what it’s like with the different gearing , seriously thinking about buying one of these , looks so mean 😍
Love watching these Kev! Very informative. It may get me back into running em again.
Hey Kev! Love how you keep it fresh with your eBay course info. Very smart about it. Keep it up buddy. That hour glass tho. 😎
You should have at least 1 million subs
I need to find a way to replace/rebuild the front bumper and rear wing, both pieces that snapped off after only jumping it 4-5 times total...
Was so hoping this video would have that since they're clearly the two parts on the car that break the most (both replacement parts are out of stock for the next 4 months)
Im thinking about fabricating a bumper piece out of sheet metal, but I can't think of a way to fix the wing. ☹
Yes... the loctite on the pinion. It's on the motor and differential mounts too. LOL.
Kev you got me into Scot Joplin now!!!
haha epic!
Love the arrma!!!!
Nice upgrade kev!👍
My fav RUclipsr
Gosh ya make that look so easy. I’m new to this and need to do my center diffs but affraid I won’t be able to get it done. No torch pen. Where ya get that thing
Nice video kev 👍 sweet upgrades can't wait to see it rip 👊
Hey Kev do the LaTrax Teton it is cheap and backed by Traxxas you could upgrade it to do brushless aswell with a mamba micro x. PLZ
I still can’t fathom how people have the nerve to feel entitled to free stuff, especially stuff as expensive as these rc cars
ya man i know
Pretty good upgrades Kev. 👍👍👍👍
How do you snap your fingers so loud. Been trying for weeks to get that kinda volume! Can you make a How to video on the finger snap!
Love your vids keep up the great work!!!
you should try the arrma talion 6s
Hot racing parts are way way better . Just saying
Thanks for the great videos
💯✅👍🏻
Love the videos!! Thanks for your time and effort it's much appreciated!!
I'm starting to get interested in the Arma trucks, I like the body's look and if it holds up to your skate park of doom I might have to get one, good video
Do it !! You will not be disappointed I promise you
Nice video when are you going to make the video of the rustler reperations? I can’t wait
Could you say me if it’s a good rc car?
kevin Talbot Hey look it’s a fake kevin talbot impersonator!
I run 1 million fluid in my center diff 👍🏻
Hi Kevin good video as expected
U should get a monster truck body for the x max
Sweet . Thanks for the look
I got one 2 days ago so happy
Kev,you are getting a fair bit off of Banggood now. do us UK guys get hit with a lot of duty/taxes?
really like the new business plug! wasnt a big fan of the other one was kinda a little business like but this one is very good keep up the good work!! ps i am thinking of starting a rc channel myself let me know what you think!
thanks dude. Yeh go for itm youtubing is so much fun :)
@@KevinTalbotTV awesome Thanks! is it possible to edit from a laptop? i dont have a pc...
Kevin you should be using 1,000,000 weight center diff oil in all of the Arrma rigs. I have used 500,000 before and still thin after it warms up. Great videos!!!!
Ohhh shit.....loving it
looks good kevin!!
Love your vids keep it up bro
Hello kev I'm surprisingly early today.
BTW you make awesome video's
Alright kev did you upgrade the servo in any arrma yet? If so what would you recommend? Cheers bud keep bashing!!!
Ive just bought one and 3 bashes in, servo has shat itself. Seems like upgrading it is a must.
Do one like this for the slash 4x4
That's a freeking awesome RC car
i saw that you have hpi mats did you used to run their cars.
Excellent video. 👍
What is that tool you used to heat up the screws? 🙏🏼
Hopefully for Christmas I will get my first rc car
I'm curious to hear how the center diff fluid worked. I have a Kraton I can't keep on 4 wheels.
I run 50k 500k 20k in mine and it works great
What would you recommend for a new wheelie bar or rear wing I broke mine and wanted to know if it’s better stock or to upgrade it
Don’t worry bout those people kev i cant even afford a cheap Rn car let alone my dream an xmaxx. Guess time and patients is all it takes cause begging isn’t gonna get u nowhere!
Very nice video lad. Btw know were i can get a cheap Traxxas nimh battery by its self?
Try amazon or your favorite local hobby shop
Hey @kevin. What hex bits are you using mate. I'm still using cheap ones lol
What upgrades y'all do on your notorious
Loved this vid
Nice vid kev
You could do a repair week. There you are only uploading videos how you repair your rc cars
why oh why is that gear exposed on the bottom of the chasis?
Incase rocks or debris get caught it has somewhere to escape...I know it looks funny but it has a purpose
Hey, thank you!
Heyy kev!! Can you buy a Axial Yeti XL 1/8? And i love your vidéo 😁
Buy and Compare cheapest slash vs your super slash
I like gpm but takes way to long to get in the states
oh and on my talion and my dads serpent gt i put 1million in my center can it works really good and he put 20 million in his and it is like rubber so its really good so i would recommend it.
Is it not possible to go a little less ham on the throttle :P
What is that song's name !? Love it
Good Morning.
Do u think it would be hard to replace the braces with the esc on or off. And as well for the Servo
😃👍Looks great nice work.
101 about gearing taller gear does not mean better bashing you putting more strain on the motor then you put thicker gear lube is even more strain on the motor and going to make the motor hotter the esc works harder and get hotter faster taller gear smaller tires small gear bigger tires :/
Would you like to edit that and remove all those periods and commas?
@@alb9022 :\ ?
@@insanemadmanroom2299 ? :/
We will be doing a Christmas special and how are you Kev can you do a small burn out with a moped thank you
Where is the link to start selling on ebay?
Dispel this car come stock with XT90 connectors of IC5 connectors?
Were did you get those power tools
Homemade brace? Ho to video much needed
You should do more x maxx videos.
I have the v5 version with metal chassis are would I need these upgrades??
Do a modified imca car and race them that's what I'm doing to my sc10.3 it's oval racing
Hey kev I have a notorious also and both of my rear wheels were loose and I lost both drive shafts do you know how long they are?
Free?????? I would love that
Hey , where did you get your pen torch?
Hey mate jusy bought one of these just wondering if the other arrma rc cars a arms fit from rpm
what rc car diff oil weight would you use if you werent going to use the silicone earplugs?
Kev can you get a kids rc car and but a huge brushless motor and with huge tyres
Hi, could I get a link of the differential oil?