I was a former xerox tech. I don't miss xerox machines one bit. The issue is that the fuser nip is set to tightly on these fusers. The plastic gears in the fuser start binding and the machine codes out. Try taking off the cover to the fuser and loosen the nip screws 3-4 equal turns on both sides. It won't affect the toner bonding to the paper. It has worked every time, requires no parts and much faster repair.
@@srrcopiersolutions Thank you! With Xerox, I moved up over the years in what I serviced. I eventually moved up working on the C70, Versant 80, D110, Numbers 120. I had a print shop I serviced that did 2-4 million copies a month. I moved on because my company didn't want to really pay. Also handling 9 production machines along with about 50 other printers and mfp's was just overwhelming 😂.
I just inherited almost 300 of this machines (7855) in my area. I see a lot of machines showing 310-330 error, but still working. Yesterday I looked into Fault Counters on one machine and 310-330 had 204 instances of that error. Sofar, at every machine displaying that error I am able to run the motor in the service mode no problem. Also the 1st BTR contact & retract test is successful. Snooping around there I noticed that the motor itself does not have any sensors telling the machine that it is rotating. Next to the motor at about 7 o'clock I see a clutch (engaging BTR drive) and below a home position sensor telling the machine 1st BTR contact or retracted position . Looking at the fuser schematic, there is also a sensor "Fusing Unit Belt Rotation Sensor". Other then sensing the current on the motor, those are the only 2 sensors that are being able to sens no rotation from the motor. The machines I work with, are very dirty (dust). The fact that it is not permanent fault, but seems to be intermittent (in my case anyway), I tend to believe that the problem maybe in the dirty sensors. I keep reading that people replace fusers and that fixes it: confirming to me that it is the dirty sensor in the fuser...
The photocopier does not actually have a kettle that monitors the operation of the engine directly because it is unnecessary. The engine drive is transferred to other parts of the machine by means of clutches and, as you mentioned, the sensors are only there. Damage code 310-330 indicates a photocopier time delay error. Most often it is the result of a worn motor or a used fuser. If your photocopier is dirty on the back, of course, you need to clean the drive and sensors, but this is unlikely to help you fix the problem. 310-330 may appear occasionally, but ultimately leads to the shutdown of the photocopier. If the previous service charged money for each printout and photocopy, it is known that they did not want to replace the parts. The sensors in the fuser may be responsible for the paper jams but are not responsible for error 310-330. regards
2:16 There are 2 more screws top and bottom that you missed before pulling out the sbc also I would like to note you didn't need to unscrew the first 2 as the whole front end swings open with sbc in place. Cool to watch. Been doing this for 3 years now keep up the vids. 5:43 cringe its the back screws what are you doing 😆. Man you're awesome you literally responded to everyone!
P.P.S. If you need to replace your battery screwdriver, I recommend the new (2022) Makita range. Some of my batteries are over 12 years & working great.
Hello, i have a xerox wc 7530 and it started making a loud noise when its powering up and printing. Its a loud clicking noise. I tried changing the fuser as many suggested but it did not resolve my issue. Please help me.
I have a Xerox workcenter 7120 and it displays Fault Code 010-330: Fuser Motor Failure Message, do i need to change motor fuser, or is there something else i can do? Tnx for your response in advance.
Replace the engine. Why do you want to do something else? Don't forget to subscribe to my channel. Start supporting this channel and you'll get these bonuses: ruclips.net/channel/UCOHtXTtGHj33pUm8Gf2FH3Ajoin I'm already in PATREON. If you are interested, I am very happy. www.patreon.com/CopyExpertMovieStudio Check out my profile on Patronite www.patronite.pl/1796
Hello Sir Regards! My xerox 7535 shows fuser system error 310.382.00 (thermostat fail) if left on for sometime upon sending a print or anything. It also doesn't move to sleep mode and stays on low power mode even after settings. pl reply and guide. Thanks!
I have a xerox 7665 workcenter and today it started up with a Fuser System Error. I also looked at the fault history and it shows 10.320.00. Any suggestions? Thank you in advance!!!
Sir I have Xerox workcentre 7530, it always says black toner(k) empty, eve after refilling the power and replacing the toner chip, and sometimes it shows it is not a compatible toner cartridge replace the toner cartridge error... And the machine makes noise, I think it comes from gears ...
@@MrRicoh , it always makes gears full noise, I replaced with new original toner cartridge black but also same problem..dies it have any toner dispenser or motor problem..
This is why it is so HEAVY (all the internal metal). Not sure if this is a good place to ask; but I bought a similar used printer (DocuPrint IV 2275), and cannot find the menu for finding Toner levels. It weights around 130+Kg, and was a real pig to carry upstairs with the kids (where my [main] computer sits). The 775 page manual does not help as the Menu on the Printer/Scanner/Copier does not have a "MACHINE STATUS" Icon/button on mine.
P.S. It works great. The price I paid is what I would have paid for just the Toners & Drum of my existing printer (without built-in Scanner). Do I really need to use Internet/Lan? to get the scanner image to go to my PC, instead of via USB to work on (rather than using immediate print)??
@tonynogueira9593 Infelizmente não temos essa informação porque se trata de uma máquina antiga e você não pode mais comprar esse disco novo. Às vezes você pode comprar um usado no mercado secundário por cerca de US$ 20.
unknown what the problem is but have a workcentre 7830 the screen is not turning on however the lights around the display stay on but nothing else comes on. I tried to reset and unplug.
Hi Nwn Kiranja Mkuu, I ordered this element at Xerox Poland. I am a brand partner, so I have access to it quickly. Unfortunately you can't order it from me. You must find a supplier in your local market. Best wishes Tomasz Jemiołek
Does anyone know how to resolve error code 117-363 on a xerox 6128 MFP? I've tried everything that I could find on the internet without success. I was even able to start the machine in diagnostics mode and run both the Printer and Fax/Scanner diagnostics and everything reported "ok" so I don't understand why I can not rid the display of the error code as I can no longer use the printer with it there. While going through the printer diagnostics, it printed out pages that were required as part of the diagnostics so I know the printer still works. any help would be appreciated.
Hello, Code 310.382 Description Fuser Thermostat Fault. The Fuser Assembly Thermostat is broken. Remedy • Turn the power Off and remove the Fuser Assembly. Inspect the Drawer Connector between the Fuser Assembly and the Main Unit ( DJ600) for broken/bent pins, foreign substances, burns, and etc. • Check whether the MCU PWB connector P/J431 is connected properly. Measure the resistance between P600 pin-A11 and P600 pin-B9. Is the resistance infinite? Y↓ N→Check the following connections for open circuits, short circuits, and poor contacts. • Between DJ600-A1 and MCU PWB P/J431-11 • Between DJ600-B1 and MCU PWB P/J431-18 If no problems are found, replace the MCU PWB. Replace the Fuser Assembly.
Code 310.382 Description Fuser Thermostat Fault. The Fuser Assembly Thermostat is broken. Remedy • Turn the power Off and remove the Fuser Assembly. Inspect the Drawer Connector between the Fuser Assembly and the Main Unit ( DJ600) for broken/bent pins, foreign substances, burns, and etc. • Check whether the MCU PWB connector P/J431 is connected properly. Measure the resistance between P600 pin-A11 and P600 pin-B9. Is the resistance infinite? Y↓ N→Check the following connections for open circuits, short circuits, and poor contacts. • Between DJ600-A1 and MCU PWB P/J431-11 • Between DJ600-B1 and MCU PWB P/J431-18 If no problems are found, replace the MCU PWB. Replace the Fuser Assembly.
First, disconnect the ADF document feeder and try to start the copier. If this does not help, disconnect the HDD and start the copier. If this does not help, install a new power supply.
Hi Sir, could you help me with an issue? My printer is a Xerox 6655i when i got to the office this morning it was showing "Please wait...the system is powering up" and then it never powers up, it stays the same, on this green page. I already tried rebooting it but it goes back to the same message. Do you have any idea on how to solve this issue? Thank you
Xerox Workcentre 7530 always shows replace (K) black toner error even after refilling toner and replacing toner chips and even replacing with new toner cartridge, even after cleaning toner pipe assembly of black colour..any solution
I have a 3655, and when I turn on the printer, it remains static, the screen does not respond, it only prints, I have to turn off the equipment, turn it on again and it works again, but over time the screen remains static again😮💨
@@MrRicoh I already managed to solve that problem, now another one appeared, I put new toner in it and it does not recognize it, I get several errors, such as 322.319, 303.347 and all this has arisen since I changed the toner, in the area where I live there are no technicians to this trade mark
HELLO WE HAVE A PROBLEM with the xerox 5330 photocopiers all the copies with different caliber rolls we ask for help from the consultant to solve this problem we think that the problem is the temperature of the oven
Vérifiez que l'unité de fusion tourne pendant la copie. Si tel est le cas, remplacez les rouleaux d'entraînement dans la cassette à papier. Devenez mon abonné
You may have a damaged power supply. But it's possible that your 230v connection in the building has no grounding. You have to check, it's very important. I am sending greeting and I wish you good luck Części do kopiarek www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Części używane www.copy-expert.com/ #RICOH #COPIER #PRINTER #DRUM #TUTORIAL #PHOTOCOPIER #TRANSFER #COPIERPARTS #COPY-EXPERT #JEMIOŁEK
I want to buy the fuse drive motor. Please provide me a link from where I can get a genuine part with best price . I am facing the same problem. I am from india
Good! This is the usual Sony camera driver :) Części do kopiarek www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Części używane www.copy-expert.com/
Hello mate. My xerox 7855 recently showing fuser system error with 310.381.00 code. I tried fuser unit change and software reset but no one was helpful.can you please help me to get rid of it.
my xerox wc7545 error shown fuser system error and machine error code show is 310-330-00 and other one thing is ink is not heat on paper plz suggest some solution
Unfortunately, I do not know this error in the xerox copier Części do kopiarek www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Części używane www.copy-expert.com/ Serwis kopiarek Ricoh Warszawa sprintprintserwis.pl/
@rajeshsawant4225 Unfortunately, in this copier you first need to replace the Fuser Unit and see if that helps. If the problem recurs, you should order and replace the motor that drives the fuser unit. Do you have another used Fuser to perform diagnostics? I hope so. Write. Don't forget to subscribe to my channel. Best regards.
If you have a fuser error, you must replace the entire fuser module. But before you do that, you can clean the thermistor, so twist the fusewr and take out the thermistor, clean it, and reinstall it. Maybe it will help.
mere xerox 7535 ka fuser set work nhi ho raha hai fuser bhi kharab ho raha hai isko kahan repair karaye koyi adress de barielly me bahut mahenga bta rahe hai
It cannot be fixed in my country. I always have to install a new one. I don't know what the local market looks like in your country. Maybe someone will write to your post.
This is a known fault code. If your machine is still under warranty, please contact the seller. If you no longer have the warranty, remove the fuser and check if the thermistor is connected correctly. If that doesn't help, you will need to buy a new fuser unit.
I am sending greeting and I wish you good luck Części do kopiarek www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Części używane www.copy-expert.com/ #RICOH #COPIER #PRINTER #DRUM #TUTORIAL #PHOTOCOPIER #TRANSFER #COPIERPARTS #COPYEXPERT #JEMIOŁEK
A czy wymieniałeś rolki pobierania papieru? Taki numer katalogowy: 676K12691, 675K82242, 675K82240, 604K56080, 109R00790, 109R790, 604K66430, 22K74870, 675K86570, 675K67050, 676K65020
FUSER ERROR COMMIMG 7855 I RESET BUT AGTER SOME PRINT MAY ONE OR TWO PRINT AGAIN COMMIMG ANG MACHINE NOT TO BE START FOR PRINT EROR CODE IS 310.330.00 KINDLY HELP
First replace the Fuser Unit with a new one and then perform the reset. If there is a damage code, it means that the fuser is damaged and reset will not help. First install the new fuser.
I was a former xerox tech. I don't miss xerox machines one bit.
The issue is that the fuser nip is set to tightly on these fusers. The plastic gears in the fuser start binding and the machine codes out.
Try taking off the cover to the fuser and loosen the nip screws 3-4 equal turns on both sides. It won't affect the toner bonding to the paper. It has worked every time, requires no parts and much faster repair.
Thanks for your valuable comment. I hope you will write something interesting sometime in the future. Thank you and best regards.
Well done.
@@srrcopiersolutions Thank you! With Xerox, I moved up over the years in what I serviced. I eventually moved up working on the C70, Versant 80, D110, Numbers 120. I had a print shop I serviced that did 2-4 million copies a month.
I moved on because my company didn't want to really pay. Also handling 9 production machines along with about 50 other printers and mfp's was just overwhelming 😂.
No dont do that just grease the gears works perfectly every time.
@@michaelh7527 lol why don't these clowns want to pay up!? How much did you make if you don't mind me asking?
I just inherited almost 300 of this machines (7855) in my area.
I see a lot of machines showing 310-330 error, but still working.
Yesterday I looked into Fault Counters on one machine and 310-330 had 204 instances of that error.
Sofar, at every machine displaying that error I am able to run the motor in the service mode no problem.
Also the 1st BTR contact & retract test is successful.
Snooping around there I noticed that the motor itself does not have any sensors telling the machine that it is rotating.
Next to the motor at about 7 o'clock I see a clutch (engaging BTR drive) and below a home position sensor telling the machine 1st BTR contact or retracted position .
Looking at the fuser schematic, there is also a sensor "Fusing Unit Belt Rotation Sensor".
Other then sensing the current on the motor, those are the only 2 sensors that are being able to sens no rotation from the motor.
The machines I work with, are very dirty (dust).
The fact that it is not permanent fault, but seems to be intermittent (in my case anyway), I tend to believe that the problem maybe in the dirty sensors.
I keep reading that people replace fusers and that fixes it: confirming to me that it is the dirty sensor in the fuser...
The photocopier does not actually have a kettle that monitors the operation of the engine directly because it is unnecessary. The engine drive is transferred to other parts of the machine by means of clutches and, as you mentioned, the sensors are only there. Damage code 310-330 indicates a photocopier time delay error. Most often it is the result of a worn motor or a used fuser. If your photocopier is dirty on the back, of course, you need to clean the drive and sensors, but this is unlikely to help you fix the problem. 310-330 may appear occasionally, but ultimately leads to the shutdown of the photocopier.
If the previous service charged money for each printout and photocopy, it is known that they did not want to replace the parts.
The sensors in the fuser may be responsible for the paper jams but are not responsible for error 310-330.
regards
Fuser motor gear ⚙️ slipping 😁
2:16 There are 2 more screws top and bottom that you missed before pulling out the sbc also I would like to note you didn't need to unscrew the first 2 as the whole front end swings open with sbc in place. Cool to watch. Been doing this for 3 years now keep up the vids. 5:43 cringe its the back screws what are you doing 😆. Man you're awesome you literally responded to everyone!
Thanks for your comment.
P.P.S. If you need to replace your battery screwdriver, I recommend the new (2022) Makita range. Some of my batteries are over 12 years & working great.
I have no problem with batteries, because I get tools and batteries from the sponsors of the channel.
THANKS SIR VERY USEFULL INFORMATION MY MACHINE ERRO SOLVE THANKS A LOT....!
Thank You
On target. Thank You!
I'm glad. Another successful repair of the copier.
For replacing fuser drive motor of apeosport-vc7785, simlar?
@frankchan3242 yes it is the same
Hello, i have a xerox wc 7530 and it started making a loud noise when its powering up and printing. Its a loud clicking noise. I tried changing the fuser as many suggested but it did not resolve my issue. Please help me.
You must check the Fuser Unit driving wheels at the rear of the machine near the engine. There is probably damage there.
I have a Xerox workcenter 7120 and it displays Fault Code 010-330: Fuser Motor Failure Message, do i need to change motor fuser, or is there something else i can do? Tnx for your response in advance.
Replace the engine. Why do you want to do something else? Don't forget to subscribe to my channel.
Start supporting this channel and you'll get these bonuses:
ruclips.net/channel/UCOHtXTtGHj33pUm8Gf2FH3Ajoin
I'm already in PATREON. If you are interested, I am very happy. www.patreon.com/CopyExpertMovieStudio
Check out my profile on Patronite www.patronite.pl/1796
i have xerox 7845 but it cannot detect the network cable, what is the possible solution cos the technician is talking about board
First, update the software on your copier.
Did you reset this Error(310.330.00) by any code? Or that error disappeared after replacing motor?
The code disappears after replacing the engine. I did nothing more.
@@MrRicoh thank you for answer. I have replaced engine, but I still have this error code.
It looks like you also need to rethink the replacement of the heating unit with a new one.
Hello Sir Regards! My xerox 7535 shows fuser system error 310.382.00 (thermostat fail) if left on for sometime upon sending a print or anything. It also doesn't move to sleep mode and stays on low power mode even after settings. pl reply and guide. Thanks!
There is only one solution: replace the fuser unit if you have already checked the engine.
I have xerox wc 7545 having error 310-330 i relapsed the old moter with new one but problem exist please help me this case
Yes, this is a bug about the diagnostic software. The message is false. The truth is that you need to replace the laser.
@@MrRicoh thanks dear
@sohailkureshi6907 No problem :)
Please help, my Fuji Exrox has the power on but won't turn on
@multikarya We don't know anything about FUJI machines
hello I have the errors of 310-330 and 303-777 but also lph act fail and.
replace the engine and any solution remains the same response thank you.
Always the engine replacement helped
I have a xerox 7665 workcenter and today it started up with a Fuser System Error. I also looked at the fault history and it shows 10.320.00. Any suggestions? Thank you in advance!!!
Hello. First check that the rollers are turning slightly. Often the engine is damaged, such as in the movie, and it can also cause this error.
@@MrRicoh all rollers are turning freely. A new fuser has been put in its place and still no luck.
I have Xerox WC 7556 machine
It shows fuser system error call for assistance
Plz help me
I will pay You online
Please I need your help I have 7845 xerox machine comes with an error replace black toner inspite of its already replaced then grinding noise appears
Original toner?
Sir I have Xerox workcentre 7530, it always says black toner(k) empty, eve after refilling the power and replacing the toner chip, and sometimes it shows it is not a compatible toner cartridge replace the toner cartridge error... And the machine makes noise, I think it comes from gears ...
Did you know that Xerox has chips for a variety of markets? Euro, USA, Asia ... there are different chips everywhere.
@@MrRicoh , it always makes gears full noise, I replaced with new original toner cartridge black but also same problem..dies it have any toner dispenser or motor problem..
This is why it is so HEAVY (all the internal metal). Not sure if this is a good place to ask; but I bought a similar used printer (DocuPrint IV 2275), and cannot find the menu for finding Toner levels. It weights around 130+Kg, and was a real pig to carry upstairs with the kids (where my [main] computer sits). The 775 page manual does not help as the Menu on the Printer/Scanner/Copier does not have a "MACHINE STATUS" Icon/button on mine.
P.S. It works great. The price I paid is what I would have paid for just the Toners & Drum of my existing printer (without built-in Scanner). Do I really need to use Internet/Lan? to get the scanner image to go to my PC, instead of via USB to work on (rather than using immediate print)??
this Toner level setting can only be activated by the Service Center. You need to enter the Service mode. So, activate this option.
@@RogerThat1945 I don't know what you mean by battery
Olá tudo bem? Quanto custa a placa lógica da impressora xerox workcentre 7835??
@tonynogueira9593 Infelizmente não temos essa informação porque se trata de uma máquina antiga e você não pode mais comprar esse disco novo. Às vezes você pode comprar um usado no mercado secundário por cerca de US$ 20.
unknown what the problem is but have a workcentre 7830 the screen is not turning on however the lights around the display stay on but nothing else comes on. I tried to reset and unplug.
If your copier has a HDD, disconnect it and start the copier. If that helps, replace the hard disk with a new one. If that doesn't help, I don't know.
where can i buy it i have the same problem in xerox wc7855
can you give a link?
Hi Nwn Kiranja Mkuu,
I ordered this element at Xerox Poland. I am a brand partner, so I have access to it quickly. Unfortunately you can't order it from me. You must find a supplier in your local market.
Best wishes
Tomasz Jemiołek
godwin nyange you can order from me
My whatsapp is +8619927739304
My wechat is wuxinghaocai2019
@@mandyma6596 hello
Excellent
I hope this video helped you. This is a common glitch in Xerox copiers.
hello sir. i have wrokcenter 7855i but lost speed to 7855 and what i must to do for repair ? thk.
I do not know. Maybe someone else will write here. You may need to update the software.
xerox 7345 error code 090-330 i am able to print colour coipes in the machine please help
So far, I have not encountered this damage code. Unfortunately, I can not help you.
Does anyone know how to resolve error code 117-363 on a xerox 6128 MFP? I've tried everything that I could find on the internet without success. I was even able to start the machine in diagnostics mode and run both the Printer and Fax/Scanner diagnostics and everything reported "ok" so I don't understand why I can not rid the display of the error code as I can no longer use the printer with it there. While going through the printer diagnostics, it printed out pages that were required as part of the diagnostics so I know the printer still works. any help would be appreciated.
Hope someone can help you.
what does this fault codes stands for 310.382.00 n how to solve it please
Hello,
Code
310.382
Description
Fuser Thermostat Fault. The Fuser Assembly Thermostat is broken.
Remedy
• Turn the power Off and remove the Fuser Assembly. Inspect the Drawer Connector between the Fuser Assembly and the Main Unit ( DJ600) for broken/bent pins, foreign substances, burns, and etc. • Check whether the MCU PWB connector P/J431 is connected properly.
Measure the resistance between P600 pin-A11 and P600 pin-B9. Is the resistance infinite? Y↓ N→Check the following connections for open circuits, short circuits, and poor contacts. • Between DJ600-A1 and MCU PWB P/J431-11 • Between DJ600-B1 and MCU PWB P/J431-18 If no problems are found, replace the MCU PWB. Replace the Fuser Assembly.
Code
310.382
Description
Fuser Thermostat Fault. The Fuser Assembly Thermostat is broken.
Remedy
• Turn the power Off and remove the Fuser Assembly. Inspect the Drawer Connector between the Fuser Assembly and the Main Unit ( DJ600) for broken/bent pins, foreign substances, burns, and etc. • Check whether the MCU PWB connector P/J431 is connected properly.
Measure the resistance between P600 pin-A11 and P600 pin-B9. Is the resistance infinite? Y↓ N→Check the following connections for open circuits, short circuits, and poor contacts. • Between DJ600-A1 and MCU PWB P/J431-11 • Between DJ600-B1 and MCU PWB P/J431-18 If no problems are found, replace the MCU PWB. Replace the Fuser Assembly.
do you have a video where you show how to remove the scanner?
No
Hi,I have a problem of powering on of a machine 7535.after powering on ,it shows green screen later power off it self in few seconds
First, disconnect the ADF document feeder and try to start the copier. If this does not help, disconnect the HDD and start the copier. If this does not help, install a new power supply.
Can this problem be caused by the use of recycled sheets?
I think it is not possible.
Hi Sir, could you help me with an issue? My printer is a Xerox 6655i when i got to the office this morning it was showing "Please wait...the system is powering up" and then it never powers up, it stays the same, on this green page. I already tried rebooting it but it goes back to the same message. Do you have any idea on how to solve this issue? Thank you
Check if there is a message waiting for you in the printer driver.
What's the solution for 310.382.00 Fuser thermostat error in Xerox 7535 ?
You have to replace Fuser Unit
which Part Problem 7835 model paper jam
Każdy z elementów może być odpowiedzialny za zacięcie papieru. Najczęściej wystarczy wymienić rolki pobierania papieru.
Xerox Workcentre 7530 always shows replace (K) black toner error even after refilling toner and replacing toner chips and even replacing with new toner cartridge, even after cleaning toner pipe assembly of black colour..any solution
You probably have toners with a chip for the Asian market
I have a 3655, and when I turn on the printer, it remains static, the screen does not respond, it only prints, I have to turn off the equipment, turn it on again and it works again, but over time the screen remains static again😮💨
When was the last service and software update done?
@@MrRicoh I already managed to solve that problem, now another one appeared, I put new toner in it and it does not recognize it, I get several errors, such as 322.319, 303.347 and all this has arisen since I changed the toner, in the area where I live there are no technicians to this trade mark
HELLO WE HAVE A PROBLEM with the xerox 5330 photocopiers all the copies with different caliber rolls we ask for help from the consultant to solve this problem we think that the problem is the temperature of the oven
🔥🔥 Get access to support bonuses RUclips MEMBERSHIP: ruclips.net/channel/UCOHtXTtGHj33pUm8Gf2FH3Ajoin
Bonjour
mon copieur Xerox 5330 affiche le code 042-310 et la feuille de sortie se bloc avant le fuser !
SVP , une aidée ?
Vérifiez que l'unité de fusion tourne pendant la copie. Si tel est le cas, remplacez les rouleaux d'entraînement dans la cassette à papier. Devenez mon abonné
How techer' lwant help from you ' can lfind you? Service manual xerox c70
www.manualslib.com/products/Xerox-Color-C60-C70-Series-3591848.html
Bonsoir je voulait le pilotes de imprimantes HP laser jet p 3015 est je ne s'est comment faire pour téléchargé
Unfortunately, I do not know about it
Hi, I have a rexox 7545 and it only displays fuser system error, no error code. Can you help me.
I check in such cases the engine driving the Fuser Unit. If it does not help, I put in another second Fuser
@@MrRicoh thank you so much. I handled it
Sir my xerox 5755 machine produce noise whenever i start the machine..
Please guide me how can i solve the problem
In my opinion the noise is most often from the Fuser unit. Maybe you have worn bearings
sir piz colour 7845 xerox machine full wiring is necessary
I do not understand
Can you tell me if you can purchase this spare part?
Now it's not with my suppliers.
sir i have 5845 i press r3 as paper jam issue and suddenly system power shut no power on machine in right now what would be the problem
You may have a damaged power supply. But it's possible that your 230v connection in the building has no grounding. You have to check, it's very important.
I am sending greeting and I wish you good luck
Części do kopiarek www.copy-expert.pl/
Facebook: facebook.com/Copy-Expert-113431678801597/
Części używane www.copy-expert.com/
#RICOH #COPIER #PRINTER #DRUM #TUTORIAL #PHOTOCOPIER #TRANSFER #COPIERPARTS #COPY-EXPERT #JEMIOŁEK
I want to buy the fuse drive motor. Please provide me a link from where I can get a genuine part with best price . I am facing the same problem. I am from india
there is copy-expert.com/pl/p/Silnik-Xerox-WorkCentre-7830-7835-7845-7855-Fuser-Drive-Motor-Assembly-007K18580-/2337
My whatsapp is +8619927739304
May wechat is wuxinghaocai2019
Contact with me
hi
please help
xerox work center 7556 no display, only blinking energy light how to solved
First, replace the power supply with a different one.
Is that the new Ipad mini mini watch on your wrist?
Good! This is the usual Sony camera driver :)
Części do kopiarek www.copy-expert.pl/
Facebook: facebook.com/Copy-Expert-113431678801597/
Części używane www.copy-expert.com/
Hi i have Xerox 7835 it shows on screen reset device power off the device can u help me plz i try to power off it but it still showen the seem error
Not enough information
Hello mate.
My xerox 7855 recently showing fuser system error with 310.381.00 code.
I tried fuser unit change and software reset but no one was helpful.can you please help me to get rid of it.
Maybe replace the engine
Sir my machine 7855 is got start (On hi nahin hoti) what I will do
Not enough information. Enter the counter, error code.
what is the causes of that problem!!idon experience
it is normal wear - these elements are simply damaged
Mbn
my xerox wc7545 error shown fuser system error and machine error code show is 310-330-00 and other one thing is ink is not heat on paper plz suggest some solution
replace the same engine as I mention in the movie
@@MrRicoh sir one thing is when I start the machine then show fuser system error and black ink on black drum show what is this?
My machine's print not heat. Ink is not heating
Check and replace thermostat and thermistor in fuser unit
New MCU board installed after 310-381 error code shown please solution
Are you my subscriber?
@@MrRicoh yes
Please help me
My printer c5575 error code 065-223
Cannot scan..please
Unfortunately, I do not know this error in the xerox copier
Części do kopiarek www.copy-expert.pl/
Facebook: facebook.com/Copy-Expert-113431678801597/
Części używane www.copy-expert.com/
Serwis kopiarek Ricoh Warszawa sprintprintserwis.pl/
error code
310.378 heat belt rotation fail
xerox 7556
@rajeshsawant4225 Unfortunately, in this copier you first need to replace the Fuser Unit and see if that helps. If the problem recurs, you should order and replace the motor that drives the fuser unit. Do you have another used Fuser to perform diagnostics? I hope so. Write. Don't forget to subscribe to my channel. Best regards.
xerox 7830 error 310-372-00 how to fix?
Try 744-001 to reset fuser error Press & hold 0 button for 5-6 seconds then symultaneously press start button.
Passwd = 6789
necesito ayuda , tengo el mismo codigo de error,
¿Qué ayuda esperas? Necesitas comprar un motor nuevo e instalarlo. No hay otra solución
@@MrRicoh hola.. donde lo consigo, me puedes apoyar, soy de mexico
I have xerox 7556 machine
It shoes fuser system error call for assistance
Please help me sir
I will grateful to you
I will pay you online
If you have a fuser error, you must replace the entire fuser module. But before you do that, you can clean the thermistor, so twist the fusewr and take out the thermistor, clean it, and reinstall it. Maybe it will help.
mere xerox 7535 ka fuser set work nhi ho raha hai fuser bhi kharab ho raha hai isko kahan repair karaye koyi adress de barielly me bahut mahenga bta rahe hai
It cannot be fixed in my country. I always have to install a new one. I don't know what the local market looks like in your country. Maybe someone will write to your post.
Altalink B8045, Error Code: 14-517-00?
Look this: www.support.xerox.com/en-us/article/en/2076174.html
How to different fuser assembly wc 7545 and wc 7525
These are completely different products. You cannot use them interchangeably
I have Xerox 7435 and its error is 010-311
This is a known fault code. If your machine is still under warranty, please contact the seller. If you no longer have the warranty, remove the fuser and check if the thermistor is connected correctly. If that doesn't help, you will need to buy a new fuser unit.
Bhai Meri Machine me fuzr error bta rha kitna kharcha a jaiga change krane ka
I do not know. There are different prices in each market. I got $ 150 US
🔥🔥 RUclips SUPPORT: ruclips.net/channel/UCOHtXTtGHj33pUm8Gf2FH3Ajoin
Hello can I please help me
Write
xerox 7830 code error 342-332-00 how to slove ?
I think you need to replace the Fuser Unit or the thermistor
Sir my machine xerox 7845I
Reset machine aa rha
Solutions please
www.support.xerox.com/en-us/article/en/1335747.html
Become my subscriber
Nice
I am sending greeting and I wish you good luck
Części do kopiarek www.copy-expert.pl/
Facebook: facebook.com/Copy-Expert-113431678801597/
Części używane www.copy-expert.com/
#RICOH #COPIER #PRINTER #DRUM #TUTORIAL #PHOTOCOPIER #TRANSFER #COPIERPARTS #COPYEXPERT #JEMIOŁEK
Thanks, just tried this and my printer went back online.
good job
i realize Im kind of randomly asking but do anyone know a good site to stream newly released movies online ?
Servisnoe menu xerox
Unfortunately I don't have this copier anymore so I can't help you.
Vous avez un numero de telephone ?
xerox workcentre 7556 paper not period
A czy wymieniałeś rolki pobierania papieru? Taki numer katalogowy: 676K12691, 675K82242, 675K82240, 604K56080, 109R00790, 109R790, 604K66430, 22K74870, 675K86570, 675K67050, 676K65020
31038200
what does it mean?
@@MrRicoh stablizer on Karne par bhi machine on nahin hoti
Aisa Lagta hai ki uski main supply kharab ho gai hai
FUSER ERROR COMMIMG 7855 I RESET BUT AGTER SOME PRINT MAY ONE OR TWO PRINT AGAIN COMMIMG ANG MACHINE NOT TO BE START FOR PRINT EROR CODE IS 310.330.00 KINDLY HELP
First replace the Fuser Unit with a new one and then perform the reset. If there is a damage code, it means that the fuser is damaged and reset will not help. First install the new fuser.