The temperature should be ideally around 210°c. The heating time, pressure, cooling and bead thickness is as per dvs 2207-1 and is7634. Call me on 9820949802 direct for more info
That's a horrible fuse. 1. Pipe on the left was barely faced. You should get ribbons like what was coming off the pipe on the right. 2. You didn't let the heat plate reach temperature before using it. The light was red, which means it was still heating and not to temperature. Wait for the green light to start your heatsoak. 3. Your beads aren't rolled over because the pipe wasn't hot enough (you put the heat plate on way too soon) and you didn't apply enough pressure when fusing. The second part doesn't matter in this instance though, because the pipe wasn't hot enough to begin with. I bet you could just pull those two pieces apart after the required cooling time; and if you couldn't pull them apart by hand, 100% if you dropped that on the ground, it would immediately separate.
@@Polymold there is no standard machine without pressure measurement device. It's only a jugaad. for more information read DVS2207-1 & make something standard based machine not this type shit.
sure i agree, but you can always measure the bead thickness. ultimately pressure determines bead thickness and if that is within the standard, the joint is good !!!
Thanks brother 👍👍👍
Can you send me the heating time table..
सर जी हमें यह मशीन चाहिए
Call 9820949802
Helpful video
Thank you
This machine is cost tell me brother
Please call on 9820949802
@@Polymold hai
What is your price in joint machine
Call direct for price on 9820949802
Yah machine kaun si company ki hai kahan milegi
Machine Price? Where to buy?
Call 9820949802
Eska price kya hai bhai aaur kmse km aur jyada se jyada kitne inches ki pype lgti hai
Call 9820949802
How much the price. I'm from Malaysia
email polymold@gmail.com
Kitne me ye padegi ky arate hai
Direct number 9820949802 pe call kare please
@@Polymold how meni prise
Call direct on 9820949804
May you help me with sharing the heating standard
The temperature should be ideally around 210°c. The heating time, pressure, cooling and bead thickness is as per dvs 2207-1 and is7634. Call me on 9820949802 direct for more info
ye joint kitne years tak tikega underground water pipe line me
Approx 50 years, यह 50 साल तक चलेगा
अपेक्षित जीवन न्यूनतम 50 साल है, इसलिए इसे लंबे समय तक चलेगा
Kaya ret hai ji
Call me directly on 9820949802
Where is the shop and dealership
Mumbai , contact 9820949802
क्या आप मुझसे व्हाट्स अप से जुडना पसंद करेंगे,,?
9820949802
Ye mashin kaha milegi or praice kya hai
Call Karo 9820949802 , Mumbai
Retale in pak please
😮
सर, मुझे आपसे मशीन खरीद नी है, क्या आप मुझसे डिल करणा चाहूंगा
Call 9820949802
Machine ki kimat kya hai
Message on 9820949802
Iska price kiya hai
Rs 36000 + 18% GST, ex Mumbai
मेरे को चालू नेट चाहिए
Machi pakadne wali net ?
Prije,pasa
call 9820949802
Price send
Send your email id
Price
call 9820949802
यामशिनचीकीमतकाय आहेवकोठेमीळेल
9820949802
Se puede hacer mejor.
रेट क्या है
Call 9820949802
Çà c'est plus pratique ...
bien sûr et ça fait des joints parfaits aussi
M.R.P
Please send email to polymold@gmail.com
प्राईज
MRP kya hai
Call on 9820949802
रेट
call 9820949802
Kya yaar itna music laga rakhe ho
Mute button daba do bhai
Ok
Reat sir
call 9820949802
Butt fusion machine reat & contect number
hi, thank you for your comment
please call me on 9820949802
or email polymold@gmail.com for rates and delivery
That's a horrible fuse.
1. Pipe on the left was barely faced. You should get ribbons like what was coming off the pipe on the right.
2. You didn't let the heat plate reach temperature before using it. The light was red, which means it was still heating and not to temperature. Wait for the green light to start your heatsoak.
3. Your beads aren't rolled over because the pipe wasn't hot enough (you put the heat plate on way too soon) and you didn't apply enough pressure when fusing. The second part doesn't matter in this instance though, because the pipe wasn't hot enough to begin with.
I bet you could just pull those two pieces apart after the required cooling time; and if you couldn't pull them apart by hand, 100% if you dropped that on the ground, it would immediately separate.
Tradu în romănă
My kol
Please call direct on 9820949802
Hi.sudhir kumar
Where can I order this?
गेम ची किंमत काय आहे आणि कुठे
call 9820949802 - Mumbai
Pl
Call direct on 9820949802
This is not standard procedure and machine has no pressure measurement. Total non standard.
No pressure gauge, at low price , however, all other parameters are controlled. End result also matches standard. So it works !
@@Polymold there is no standard machine without pressure measurement device. It's only a jugaad. for more information read DVS2207-1 & make something standard based machine not this type shit.
sure i agree, but you can always measure the bead thickness. ultimately pressure determines bead thickness and if that is within the standard, the joint is good !!!
यह मशीन चाहिए काॅन्टक नंबर सेंड करें
Yah machine chahie contact number send
😂
9820949802
प्राईज