Domaca pamet kad proradi iz radionice drago mi je kad vidim da neko radi sa apetitom vidi se da si perfekcionista nista ne prepustis slucaju.👍 Pozdrav iz Srbije
Very good. Then thinking of adding a big bottle jack with corded drill instead of a lever. Wanting to build my own exhaust system. Again thanks for posting.
I make this sort of thing but I make sure the pry bar swings up and down for leverage. Plus there should be absolutely zero wobble, jiggle, so that all your kinetic energy goes into the bend. Also I use a really Stout long pry bar lever, makes it a cinch no struggle. Especially when you have to do hundreds and thousands of bends,💥 that's my two cents. Great job by the way. The next one I'm building, bends to solid bars at once.
Queria eu ter a metade das ferramentas que ele utilizou. Mas é inegável a habilidade do rapaz. Ficou muito bom o trabalho. Parabéns!!! Congratulations!!
The video was quite cinematic as if someone had written the screenplay. Didn't skip a second like I do with most videos. A very interesting and informative one. Keep it up bro. GBU
Nice build. Only concern I have is the welded center pivot. The plating on those commercial bolts makes welding them sketchy. Make the center pivot 5mm longer and pass it through the baseplate, then weld the head from the other side. That will send the bending forces through the shank of the bolt into the baseplate, instead of through the welds on the sides of the bolt head.
Excelente forma de trabajar voy a ordenado muy ordenado muy limpio tienes muy buena herramientas todo excelente lo único que faltó fue una base de cemento en el patio para colocar la curvadora saludos desde Colombia
you prolly dont give a damn but does someone know of a tool to get back into an instagram account..? I stupidly lost the password. I would love any tricks you can offer me
I wasn't going to say anything, but with 7 million views, you have some responsibility to the people to be honest and point out that this does not work well and that it is far from idea. You are going to motivate people to purchase dies and materials to make this tool, and it will be a waste. I can see from the video that the bends are not consistent (the radius is changing) and the bends are damaging the pipe, unlike a properly built bender. This was a fail, and should have been labeled as such... or at least pointed out that this was NOT idea and the results were not great. Instead you hyped it up like it all went to plan. People. If you are going to bend different size pipe, you should be using the appropriate size die and follower. If you are going to bend more than one size of pipe with one bender, you need to have an adjustable follower or keep your follower close to the die to avoid kinking and other issues. This would be a good video IF it didn't end giving the audience the idea that you can repeat this process and be happy with the results.
Hello Doctor D S. I'm Jessie from Philippines. Nice work and video. Will try to make this. Useful for the beginners in DIY things. Thank you for the informative video. Great Job sir! 🙂👍
Trebas ga malo preraditi,jer ovako mozes savijati cevi samo do odredjenog precnika(fi). Jedan roler si trebao napraviti da se moze štelovati pa tako da mozes savijati i deblje cevi. Inace korisna stvar. Pozz iz Srbije 👋
It looks like it's made for 1 size of Pipe only.The rear anchoring back U shaped plate should have been made to accomodate several different sizes. Otherwise I like how it has degree markings capabilities.
Wow awesome build thks for shari ya dont need to be rocket scientist to do this great idea going to build oe great for building gocarts and Old School Choppers so from Canada 🇨🇦 SK later 😊ya got this 👍
Zanimljiv video, odlična savijačica. S istom možeš si praviti vilice od rebrastog (šipki) željeza za armirani beton kod nadvoja, zidova, temelja i slično. Bravo Doctor. Veliki pozdrav!
I made something like that for .500 tubing. Many years ago. I use a bearing on the small wheel. I Mande the wheels. I used a .500 wide tool bit. With the radius on it. Great job. Keep up your great work.
good idea, the only bad thing is the axis of the main mold welded to the plate and of greater diameter, the best would be past and thicker, it is observed how it moves by the applied force.
9:52 some people build their own bars but i just like dont have that type of a brain id have to commision somebody else to do it because i have no knowledge im metal working
I think it’s a great built even if it’s not 100% it will work only thing I would add is interchangeable wheels for bigger sizes
You've got every tools every piece wow 👍
Domaca pamet kad proradi iz radionice drago mi je kad vidim da neko radi sa apetitom vidi se da si perfekcionista nista ne prepustis slucaju.👍
Pozdrav iz Srbije
Potpuno se slazem da je veliko zadovoljstvo gledati mladog momka kako ima zelju i znanje za rad.
Ali od ovog momka bolji je momak na kanalu peChoO
Apesar de ser tão jovem, porém muito sábio e incrível a tua sabedoria além de ser super organizado. Está de parabéns você é um excelente profissional.
a very useful video, as long as people watch it, the more God's reward flows for you.
Straight onto business. That's what I call a workshop
Very good. Then thinking of adding a big bottle jack with corded drill instead of a lever. Wanting to build my own exhaust system. Again thanks for posting.
I make this sort of thing but I make sure the pry bar swings up and down for leverage. Plus there should be absolutely zero wobble, jiggle, so that all your kinetic energy goes into the bend. Also I use a really Stout long pry bar lever, makes it a cinch no struggle. Especially when you have to do hundreds and thousands of bends,💥 that's my two cents. Great job by the way. The next one I'm building, bends to solid bars at once.
Queria eu ter a metade das ferramentas que ele utilizou. Mas é inegável a habilidade do rapaz. Ficou muito bom o trabalho. Parabéns!!! Congratulations!!
The video was quite cinematic as if someone had written the screenplay. Didn't skip a second like I do with most videos. A very interesting and informative one. Keep it up bro. GBU
Exelente maestro, no le doy un aplauso sino un millon, felicidades
Como de llama ese material redondo que esa para doblar los tubos??
The first construction of the new workshop, it is so much more rewarding to make your own tools 🛠
Ррр
П
Good videos tutorial next time boss 👍👍👍
Nice build. Only concern I have is the welded center pivot. The plating on those commercial bolts makes welding them sketchy. Make the center pivot 5mm longer and pass it through the baseplate, then weld the head from the other side. That will send the bending forces through the shank of the bolt into the baseplate, instead of through the welds on the sides of the bolt head.
Excelente forma de trabajar voy a ordenado muy ordenado muy limpio tienes muy buena herramientas todo excelente lo único que faltó fue una base de cemento en el patio para colocar la curvadora saludos desde Colombia
Красава , просто быстро и эффективно !!👍👍👍👍
you prolly dont give a damn but does someone know of a tool to get back into an instagram account..?
I stupidly lost the password. I would love any tricks you can offer me
@Jairo Jake instablaster =)
I wasn't going to say anything, but with 7 million views, you have some responsibility to the people to be honest and point out that this does not work well and that it is far from idea. You are going to motivate people to purchase dies and materials to make this tool, and it will be a waste.
I can see from the video that the bends are not consistent (the radius is changing) and the bends are damaging the pipe, unlike a properly built bender. This was a fail, and should have been labeled as such... or at least pointed out that this was NOT idea and the results were not great. Instead you hyped it up like it all went to plan.
People. If you are going to bend different size pipe, you should be using the appropriate size die and follower. If you are going to bend more than one size of pipe with one bender, you need to have an adjustable follower or keep your follower close to the die to avoid kinking and other issues.
This would be a good video IF it didn't end giving the audience the idea that you can repeat this process and be happy with the results.
Excellent!!! 😁👍Although, you might have to heat it with a torch to make it easier.
Excellent presentation. The Lord God bless you in Jesus mighty name
No pues... tienes un buen de herramienta.
¡ Tienes una ferreteria!
Yo a luchas tengo unas pinzas ☹ .
Pero exelente trabajo 😀.
Me gustó lo que hiciste.
welding on a wooden table is a bad idea bro!!! great bender
Great little project, nice finish. Great video, thanks. 😊
Where did you get the roller dies frome i cant find those any where! Help!!!
CHECK A SCRAP METAL YARD, ALWAYS CHEAP FINDS! 🇺🇲👍✌️
🙏Sir Excellent your job keep your blessing us 🙏 i from mumbai india
you need thicker plate and a more solid handle. a few more bends and its going to bend or break
Hello Doctor D S.
I'm Jessie from Philippines.
Nice work and video.
Will try to make this.
Useful for the beginners in DIY things.
Thank you for the informative video.
Great Job sir!
🙂👍
❤
Well done, in my opinion, you just needed to make a 90-degree fold and another 180 to see how the curves will be.
llllllll
7
Cho tôi hỏi ! Vì sao khi tôi uấn ống kém lại bị gẫy mà không giữ được độ tròn của ống ạ ...
@@cuongnguyenduy8141 .
Отличная работа! Спасибо за видео!
Fantastic!. But where to get those wheels?
Were you able to find any
@@johnnymcclurg9672 in a F1 race car?? 😋
Google Rollers with U Groove
i follow Leandro Torneiro, an brazilian maker doing this project and must tell, this tool is awesome!
Keep up the good work 👍
Awesome! Im new to metal work... and would love a pipe bender... Gonna have to wait a whil longer before I can do anything like that!
Dobra ideja,pravio sam sebi nesto slicno,ide to mnogo lakse uz grejanje
ruclips.net/channel/UC6ioKYOovUi9r8h4orOQ8pQ
alguien q m proporcione el precio y en dónde la pueda conseguir vivo en Chalco estado de México x favor
This is fantastic, I wish to have a work shop like this with all these machinery, thanks for your good education. Watching from GH,
ฟฃฃวฃ
LOOKS AND WORKS GREAT, THANKS FOR SHARING. CAN YOU MAKE A METAL ROLLER TO ROLL FLAT METAL PIECES? 🇺🇲🌞👍✌️
9oooo
Nice👍
Is this guy working inside a hardware store? 🤔
Bu harika bundan ilham alarak aynısını yaptım 😊👍👍👍👍🇹🇷🧿
Where did you get the wheels?
Good idea! Thanks for sharing. Keep safe. Watching here in Canada
Step 1 - have all the key expensive components of a retail bender tool...
Ottima costruzione, molto robusta, 👍👍
How do you make the dies?
Trebas ga malo preraditi,jer ovako mozes savijati cevi samo do odredjenog precnika(fi). Jedan roler si trebao napraviti da se moze štelovati pa tako da mozes savijati i deblje cevi. Inace korisna stvar. Pozz iz Srbije 👋
It looks like it's made for 1 size of Pipe only.The rear anchoring back U shaped plate should have been made to accomodate several different sizes.
Otherwise I like how it has degree markings capabilities.
Hey man great job but I see a problem it’s flexing needs more reinforced and needs to be mounted to concrete not a wooden workbench
ALI JE LIDL PRAKSIDE PLAZMA DOBAR PRODUKT ALI GA VI PRIPOROČATE PROSIM odgovor i stvarno lepo delavnico imaš pozdrave iz Slovenie
Jednostavno ODLICNO💪😂
What happen to measure twice cut once?
Wow awesome build thks for shari ya dont need to be rocket scientist to do this great idea going to build oe great for building gocarts and Old School Choppers so from Canada 🇨🇦 SK later 😊ya got this 👍
Smart and effective!
O
Zanimljiv video, odlična savijačica. S istom možeš si praviti vilice od rebrastog (šipki) željeza za armirani beton kod nadvoja, zidova, temelja i slično. Bravo Doctor. Veliki pozdrav!
Пп
I’d love to make one. Where did you get the die rollers?
Same question!! I can make them, but it's not easy...
Awesome tools,,wow can i have 1 hehehe ☺️☺️☺️
How're Parkside plants?
Svaka cas odlicna masina i dobar tutorial kako da napravimo 💪💪💪
Easy when you got All the tools 😂
Tooo samo tako nastavi imaš moju veliku podršku
Nice, where do I get the wheels ?
Roller with U Groove
I made something like that for .500 tubing. Many years ago. I use a bearing on the small wheel. I Mande the wheels. I used a .500 wide tool bit. With the radius on it. Great job. Keep up your great work.
Thanks 👍 Alhamdulillah
I think ,it was a little bit to light .😁
But working good .👍
Greetings, you can add a little bit of oil to make it easier to slide
good idea, the only bad thing is the axis of the main mold welded to the plate and of greater diameter, the best would be past and thicker, it is observed how it moves by the applied force.
The most important part are the pulleys, where did you get them?
Excelente información gracias👍👍👍
Great work
hello where did u get those bender dies/wheels please?
Boa tarde! Gostaria de ter muitas ferramentas assim... parabéns pra você!
dads gonna be pissed ha ha bending his pipes up lol jp
Extremely good. Very beneficient.
.
Where can I get the pulleys?
Apotek
Bro I think you crazy and love with tools
Nice work idol
Looks like it would kink some thinner walled stuff though.. maybe if you took another pulley any cut it in half to use as the support part..
GOOD IDEA SO MUCH
Me watching this : he is a profesional 👍
Svaka čast 👍👍👍
Ijin nyimak bosq👍👍👍👍👍matap...❤❤❤❤👌🙏
where did the round discs / pullys come from?
They come from either working or having connections in the steel manufacturing industry.
MAX! Everytime I saw MAX! I said MAX!
Yet another DIY'er who uses a vernier gauge as a scriber... puts me off straight away.
Guess what.
There are cheap ones... you cannot believe how "common" this practice has become. Yes buy a cheap caliper instead of a scriber compass.
the tools are complete.. thank for sharing
9:52 some people build their own bars but i just like dont have that type of a brain id have to commision somebody else to do it because i have no knowledge im metal working
ruclips.net/channel/UC6ioKYOovUi9r8h4orOQ8pQ
ruclips.net/channel/UC6ioKYOovUi9r8h4orOQ8pQ
Odlična ideja i još bolja izvedba. Samo tako dalje... 👍💪
Well done 👍🏻
I like your shop 👏👏. Good job
Where can someone by the round dye pieces at!!!???
Excelente video felicitaciones👍👌👍🙏🙏🙏🇦🇲🇦🇲🇦🇲
Koju si školu završio
nice but does it work properly on hollow pipe??. I mean clean bend??
Pozdrav Davide.Kako se zovu ovi kolutovi sto savijaju cjev
Nice bender... Good job sir.
👍👍👍👍💯
Good job bro..🌟🌟🌟..
Intelligent. Boss. Realy
Super Congratulations 🌹
Tebi nikada nemoze biti dosadno,radis to sto volis a opt se zabavis,a i napravis nesto korisno.
0
good job but i believe heating it with heating torch helps a lot also
Gool🔥
from Algeria the first