Thanks for these; I used your first tutorial to get my TSR-700 up to speed months back, and just happened to catch this one which reminded me to update last night!
thanks for that! I'm now in fw 1.60 is that normal that in tv input I get no video overlay when I go in settings? the TV screen goes black and I only see the setup or option menu.
Hi there, I have the same problem. Apple tv to HDMI 1 then hdmi arc out into hdmi arc tv. I can hear the sound but no display. Can you help me on this. We also have the same receiver
I have a new TSR-700 receiver. I cannot get my subwoofer to play. When I use YPAO to balance the speakers, I get a test tone from the Subwoofer. But when I run the tone test, I do not get any sound from the Sub, nor does it work when I play music. I have swapped out cables (no effect) and have the same result when trying another Subwoofer. I have my system set up as a 5.1 system and am using the LFE connector on the Sub (Jamo C 912). Any suggestions would be helpful as I have gone through menu settings ad nauseam.
Is the context your playing pushing a minimum of 5.1? You can also test by changing front speakers to “small” so it forces the subwoofer to play anything under 80hz
Got the tsr 700 a couple weeks ago. Upgrade from Rx v596. So far it's been good, just having to go through all the settings is a pain. I been using straight over dolby, been having super low sound and dialogue. now it's better. Just fine turning the subwoofer, it's been super low. Might have to get a new one.
I'm about to buy a new AVR as well. I have the tsr 700 but the bass is low. I got two 12 inch monolith subwoofers the bass is low. I tried the calibration single point. Base was good but low. I tried multi point base got super low. Tried using the umik 1 to calibrate and even got a mini DSP 2x4hd for the subs and still low bass. I'm done with this one. Need a new AVR
@@g4mer-d3v1l5 I got my bass back. I think the calibration doesn't give the right dB level sometimes. I did bumped it up a lot, under level setting it's at +10 dB. And under tone control bass is +4. On my sub itself, I have the gain at 8.
@@TacticalFlow i read on several forums that raising the bass pas 0 on the level that it can have problems. So I try to keep it under 0 or right at 0. Now I have to see the sub control you mention and move this setting see i it gets better. The gain on the back of the subs is at 6 I think.
When you ask order of positions for you mean which speakers it pushes the spatial frequency tones to adjust the setup? If so front left the right. Then rear left then right, ATMOS (if applicable) and finally Subwoofer.
Hi Sir SugarRey's, I have some difficulties to make a settings of my AVR RX V6A like the Tone Control,Lipsync, Dialogue Level, Volume Trim Ypao Subwoofer Trim etc. I made a settings in many times then I'd turn the memory guard set to on after sometimes those all turn back to default mode! That's my problem sir SugarRey's.. So I ask to you some guide on how to achieve these settings. Thank you Sir SugarRey's From the Philippines 🇵🇭 God bless to you and your channel 🙏
Hello SugaRey, I am really enjoying your videos related to the RX-V6A. I have ordered this receiver and can't wait to set up my home theater (5.1). I am new to all of this. My question is: my older TV doesn't support ARC but has CEC. I have an NVIDIA Shield that supports Dolby Atmos. Will Dolby Atmos work if I connect the Shield to the receiver? My TV will be connected to the receiver with HDMI and an optical cable. Thanks
Would it be possible to do a quick explanation video on the different audio settings like pure direct vs straight vs auto etc. Thanks for doing the videos on the 700.
i actually have a problem with my current setup using a Samsung Q95T and the RX V6A (TSR-700) connected with a hdmi e-arc cable. The problem is that the AV is not being recognized by the TV when turning on. After a few seconds it says, "no source" i have to manually select the HDMI e-arc on my tv because its switching to normal TV-speakers everytime i turned it off. After selecting in AV settings AV to HDMI Control = ON and ARC = on it works again. but when i turn on my ARC = ON my AV wont start on auto when turning on my TV. its super frustrating, another problem whats happening is that my sound wont start right at the beginning watching videos on youtube/netflix/amazon etc. it takes like 5-15 seconds. The HDMI cable is 3 meters long is this maybe a problem ? Oo
How does the 4k upscaling works on the receiver if we play 1080p video? Does it really upscaling the video to 4k? Can you please make a video on this 4k upscaling with demo
It's pretty basic I would say.or in other words your lower resolution still looks the same.my Sony tv upscaling is much better and hence I don't use AVR one
Thanks for these; I used your first tutorial to get my TSR-700 up to speed months back, and just happened to catch this one which reminded me to update last night!
Glad it helped you Gary! Appreciate the feedback.
Literally could not figure out why it wasn't working after the update. This just saved my sanity, thanks!
Thank you for the feedback. I’m glad it helped Twest.
You can also reboot the reciever in the music cast app too without unplugging if its hard to get too
Hi I used this video to set up my receiver Thanks!! but how do you change to ALL STEREO on this receiver did not see you mention that thanks!
Great help. Thanks!!!
thanks for that! I'm now in fw 1.60 is that normal that in tv input I get no video overlay when I go in settings? the TV screen goes black and I only see the setup or option menu.
Hi there, I have the same problem. Apple tv to HDMI 1 then hdmi arc out into hdmi arc tv. I can hear the sound but no display. Can you help me on this. We also have the same receiver
Thanks
Great Video. 👍
Question, if I made changes to any settings, should I do a back-up first and then after the upgrade, do a restore?
How to get the music cast to work as I’m having problems with it not showing in my Wi-Fi settings???
I have a new TSR-700 receiver. I cannot get my subwoofer to play. When I use YPAO to balance the speakers, I get a test tone from the Subwoofer. But when I run the tone test, I do not get any sound from the Sub, nor does it work when I play music. I have swapped out cables (no effect) and have the same result when trying another Subwoofer. I have my system set up as a 5.1 system and am using the LFE connector on the Sub (Jamo C 912). Any suggestions would be helpful as I have gone through menu settings ad nauseam.
Is the context your playing pushing a minimum of 5.1? You can also test by changing front speakers to “small” so it forces the subwoofer to play anything under 80hz
Got the tsr 700 a couple weeks ago. Upgrade from Rx v596.
So far it's been good, just having to go through all the settings is a pain.
I been using straight over dolby, been having super low sound and dialogue. now it's better.
Just fine turning the subwoofer, it's been super low. Might have to get a new one.
I'm about to buy a new AVR as well. I have the tsr 700 but the bass is low. I got two 12 inch monolith subwoofers the bass is low. I tried the calibration single point. Base was good but low. I tried multi point base got super low. Tried using the umik 1 to calibrate and even got a mini DSP 2x4hd for the subs and still low bass. I'm done with this one. Need a new AVR
@@g4mer-d3v1l5 I got my bass back. I think the calibration doesn't give the right dB level sometimes.
I did bumped it up a lot, under level setting it's at +10 dB. And under tone control bass is +4. On my sub itself, I have the gain at 8.
@@TacticalFlow i read on several forums that raising the bass pas 0 on the level that it can have problems. So I try to keep it under 0 or right at 0. Now I have to see the sub control you mention and move this setting see i it gets better. The gain on the back of the subs is at 6 I think.
Thank you very much. Can I ask you one more question? What is the order of positions when using YPAO multipoint detection in V6A?
When you ask order of positions for you mean which speakers it pushes the spatial frequency tones to adjust the setup? If so front left the right. Then rear left then right, ATMOS (if applicable) and finally Subwoofer.
@@sugarey Thanks
I just updated my rx-v6a to 1.53 and would like to know what it was for?
I can not get the audio input to properly display on the screen.. it displays DD no matter what the input is coming into the receiver
Hi Sir SugarRey's, I have some difficulties to make a settings of my AVR RX V6A like the Tone Control,Lipsync, Dialogue Level, Volume Trim Ypao Subwoofer Trim etc. I made a settings in many times then I'd turn the memory guard set to on after sometimes those all turn
back to default mode! That's my problem sir SugarRey's..
So I ask to you some guide on how to achieve these settings.
Thank you Sir SugarRey's
From the Philippines 🇵🇭
God bless to you and your channel 🙏
Hello SugaRey, I am really enjoying your videos related to the RX-V6A. I have ordered this receiver and can't wait to set up my home theater (5.1). I am new to all of this. My question is: my older TV doesn't support ARC but has CEC. I have an NVIDIA Shield that supports Dolby Atmos. Will Dolby Atmos work if I connect the Shield to the receiver? My TV will be connected to the receiver with HDMI and an optical cable. Thanks
Let me do some research on the NVIDIA Shield and get back to you.
@@sugarey Thank you, apologies, It's a Nvidia Shield PRO
Would it be possible to do a quick explanation video on the different audio settings like pure direct vs straight vs auto etc. Thanks for doing the videos on the 700.
Yes, I will work on that and get it on line soon.
Can I connect my echo studio to my Yamaha RX-v6a also have my 5 speaker connected. I don’t have subwoofer.
How do you mean connect? To be used as a source? Or to use as a speaker?
@@sugarey connect as a speaker. Thank you very much
i actually have a problem with my current setup using a Samsung Q95T and the RX V6A (TSR-700) connected with a hdmi e-arc cable.
The problem is that the AV is not being recognized by the TV when turning on. After a few seconds it says, "no source" i have to manually
select the HDMI e-arc on my tv because its switching to normal TV-speakers everytime i turned it off.
After selecting in AV settings AV to HDMI Control = ON and ARC = on it works again. but when i turn on my ARC = ON my AV wont start on auto when turning on my TV.
its super frustrating, another problem whats happening is that my sound wont start right at the beginning watching videos on youtube/netflix/amazon etc. it takes like 5-15 seconds.
The HDMI cable is 3 meters long is this maybe a problem ? Oo
I finally updated to 1.48, and now my A/V drop randomly. do you know where to get the old 1.36?
How does the 4k upscaling works on the receiver if we play 1080p video? Does it really upscaling the video to 4k? Can you please make a video on this 4k upscaling with demo
It's pretty basic I would say.or in other words your lower resolution still looks the same.my Sony tv upscaling is much better and hence I don't use AVR one
Hi sir is it ok? i update mine via network thanks
I have two subwoofers, but only one is displayed when connected to V6A, is this the case for v6A
That's correct it's parallel
@@msoles30 Thanks
Jamo speakers?
I have v1.67 and cant do 120hz