hello please I need assistance I have some codes on my van sprinter cdi 315. P1956&p0101, the check engine light flashing, low power, turbo is not boosting and the engine cannot accelerate pass 30 .
… yet another great lesson here… as seen, listening to the sound of the engine when it is running can be useful in noticing when a car develops a problem.
Thank you so much for this video, it was very informative. I'm hearing the hissing sound too and experiencing loss of power uphill especially with a van full of passengers. Now I know what is Causing this problem. Thank you so much!!.
Your channel is awesome. I have a 2016 freightliner sprinter 2.1L that has been to two Mercedes dealers and they don’t want to help “we don’t work on freightliner” It is in some type of limp mode, but will still go 75mph, just takes about 3 minutes to get there. I can hear the turbo spool in the first 1-3 gears. It has one generic code I pulled from my cheap code reader: P00C2 1 Confirmed Trouble Code Turbocharger/Supercharger Bypass Valve "B" Control Circuit High Would you happen to know what I should check? I’m pretty handy. I visually checked for vacuum, the turbo actuators pull in when the vehicle is cranked. I’m not sure what to do at this point.
@TheClickSmith Send me an email, I recommend you check the turbo transducers and the circuit, and check your water pump too make sure the water pump is holding vacuum!
I really appreciated .I had accident and both air bags deployed I already put new ones on it and I send my air bag module to repair they fix I put it back on but now I only have air bag system code b1330 electrical fuse pyrothecnical separator resistance to high .. . the fuse on the positive battery cable in top of the battery was blow out I get new one from Mercedes and installed new one I tough that was the air bag crash fuse but still the air bag code present is there any other fuse or crash sensor for the air bag system in any other place located ?. could you please tell me ?. I check in front of the van but I didn't found any crash sensor in front of the van. but both air bags were deployed .. . in the accident the adblue tank unit get dent the adblue tank was empty but I fill the adblue tank .. after I fill it up the adblue tank the van drove great. after 250 miles I get in dashboard start idle message .and now the van is in limp mode I have code p13e300 the number of possible engine start is limited due to a malfunction in the adblue system ....and I have this code too p152100 the starter was disabled by the exhaust aftertreament system .. please help me with any tips I really appreciate any help . i already clean the dpf after the regenerate of diesel particular filter I get message system is complete then I tried to reset the codes but their still present and the van still in limp mode . I really appreciated your help
@Mrjfox818 since the van was in an accident the problem could be caused by so many issues, make sure the airbag module was programmed! I recommend you taske it tto a pro mechanic who can diagnosed it for you
right . did you know where the air bags crash sensor are located to make air bags deployed in case of accident ? because srs module can't be reprogramed cause still code on it . b1330 that's why need to find out where srs crash sensors are located . in advance thank you for your help @@KITS_Auto_and_Truck_Repair
@stevehvac1 the low side fuel pump should come on when the key is turned on for a about 1 - 3 minutes then it should turn off, if it remains on constantly you should have it looked at, the issue might be a shorted wire etc..
Hi, I was wondering if you could help me out please. My van told me that my vehicle was only a half tank full of AdBlue, so I filled it to the top. After I done that, I still got a sign on my van saying “AdBlue system malfunction, Emergency mode in 415 mls”. What does this mean and how do I sort this out? Thank you 😊
Excellent, thanks. I bought a Sprinter 313cdi 2.1L yesterday, and now notice it is is hissing on acceleration, producing a P0101 and P2BAC code on the OBD. I really don't know what is up with it, but from this video it has given me some hope. Do you have any idea based on those codes and the hissing? Greetings from Dublin, Ireland. J.
@@KITS_Auto_and_Truck_Repair My browser history would point to that too. Thanks for confirming. And keep up the content, it''s very informative and well delivered.
Really appreciate what your sharing here , my 2006 sprinter has the p0299 issue . It had other problems that I believed caused the issue ...firstly the air intake (plastic part) of the inlet manifold had a crack ...this caused carb to build up everywhere I've changed EGR , o2 sensor an intake and gave deep clean to everything I could access. I still have the fault next I'll get a smoke test done however i think it'll pass okay after inspections. IMO now it's turbo / actuator fault it looks like the electronic actuator is missing possibly removed is that common practice ? Or a bodged job to sell? the turbo used to work fine
Hi Deo, do you have any recommendation for a scan tool in the sub $1,000 range? Mainly want it for my 2012 Sprinter, not a full time mechanic anymore, just want to be able to fix my van myself. Thanks
@@KITS_Auto_and_Truck_Repair Vote for Autel. Anything I should beware of if considering Topdon, & x-tool too? I appreciate your videos, thanks for the help👍
Great video. I was hoping this was my issues. However I have the same code. P0299. I made a smoke tester but I could not find a leak. (I may need a better machine) I did a vacuum system test and it won’t hold vacuum. After testing each line it appears that mine is possibly from a faulty wastegate solenoid where some of the vacuum lines connect. Any experience with this? Thanks in advance.
@@KITS_Auto_and_Truck_Repair I pulled the vacuum hose off the back and tested it. Held vacuum and the rod would slide in when I pulled the vacuum and slide out when released. However I have not put a GoPro on while driving to see if it’s working through shifting the gears
Hi Deo , i have a 2015 sprinter 2500 . i dont know nothing about these van. drove it about 800 miles since bout it . i have no check engine light but what i notice is that i did not add any DEF fluid to since bought it and every time tries to add DEF i find out the tank is full . any clue of what might be going on here ? thank you
in my 2016 m Benz Sprinter 2500 2.1 Diesel engine I have accident and both air bags were deployed I put new ones already . I replace air bag module also an I put new pyrofuse the one in top in the battery but still have srs code b1330 . is any crash srs sensor some where ? I look for impact sensor in front of the van but there is not impact sensors on it . any help I really appreciate
check engine flashing light mercedes sprinter 313 cdi 2008 manual and only pull the engine do you somehow know what problem it might have thank you in advance
If it goes into limp mode you're going to get cokeing on the DPF. If they're driving it around like this too much it's never going to get to operating temperature to burn the soot off of the DPF and also without the DEF working it could possibly foul the exhaust system faster because the oily diesel fuel is not burning properly.
Can you give me your contact info. I have a 2016 Suburban that I think needs a transmission replacement. I watched your video that was posted a year ago I have the exact same truck.
@babbyjusus9221 Hi we can replace the transmission on your truck, we are located in Frederick MD, you can email us at kitsautoandtruckrepair@gmail.com to schedule an appointment!
Hi, sorry no offence, but I would use smoke machine first to see the leakage not by pressing the break in gear and accelerated you put wear to the transmission
Man it's so cool to see a mechanic who is informative about his job
ThaBrooklynFellah Thanks
Your diagnostic videos are so good I can follow along by listening only.
Thank you sir
@VentureStJohn My Pleasure! Thanks
I do lots of sprinter work. I like the way you go through your diagnostic procedure. Job well done.
the master Thank you!
hello please I need assistance I have some codes on my van sprinter cdi 315. P1956&p0101, the check engine light flashing, low power, turbo is not boosting and the engine cannot accelerate pass 30 .
Very thorough diagnosis and lesson. Well done!
Ladeisha Williams Thank you! I appreciate you!!
Probably the BEST channel about cars on RUclips, you deserve all those follow and many more, thanks for your time to teach and explain so perfect!!!
DinhaS Thank you!! I appreciate you!
THIS VIDEO IS REALLY GOOD, YOU CHECK & TROUBLE SHOOT FOR THE CAUSES OF A PROBLEM YOU DON'T SEEM TO MISS ANYTHING OUT GOOD JOB
Steve D Thank you!
the car is fixed true live data previously is worse 35 and now after fixing the boost is 45, K Diagnosti salute good works. thanks you
Suleman Habib My Pleasure! thanks
What scantool did you use?
… yet another great lesson here… as seen, listening to the sound of the engine when it is running can be useful in noticing when a car develops a problem.
Moun Bakko Thank you! That's very true!
bro your an expert of finding fault thanks alot
@ahmadzakialkozi My Pleasure! Thanks
I have a 2007 sprinter 3L diesel engine, with the same code. P0299. Thank you for the video.
Dragos B My Pleasure!!
wowzas 14 error codes lol imma have to find me a nice smoke setup like yours! Found the leak right away. Nice work thank you.
Otraphora My Pleasure!!
Real brothars come Nigeria! Thanks for your video! Very tutorial!!😮
Jorge R Davila My Pleasure Bro!
I like your thorough diagnosis & attention to detail.
Richard Zulu Thank you!!
You are good mechanic.
@ibrahimabdullah7793 Thank you!
Thank you all the way from New Zealand
@tenajnodmot My Pleasure!
Thank you so much for this video, it was very informative. I'm hearing the hissing sound too and experiencing loss of power uphill especially with a van full of passengers. Now I know what is Causing this problem. Thank you so much!!.
@esscorpshuttles7540 My Pleasure!
VERIFIED FIX, SUPPORTED WITH DATA ALL ALONG. PERFECT.
sam bitar Thank you!
I would like to see the process of replacing the intercooler, if you already have a video can you share a link. But great diagnostic video. 👍
@roberttait2169 Thank you! I have the intercooler replacement video in my sprinter playlist!
Your channel is awesome. I have a 2016 freightliner sprinter 2.1L that has been to two Mercedes dealers and they don’t want to help “we don’t work on freightliner”
It is in some type of limp mode, but will still go 75mph, just takes about 3 minutes to get there. I can hear the turbo spool in the first 1-3 gears.
It has one generic code I pulled from my cheap code reader:
P00C2
1 Confirmed Trouble Code
Turbocharger/Supercharger Bypass Valve "B" Control Circuit High
Would you happen to know what I should check? I’m pretty handy. I visually checked for vacuum, the turbo actuators pull in when the vehicle is cranked. I’m not sure what to do at this point.
@TheClickSmith Send me an email, I recommend you check the turbo transducers and the circuit, and check your water pump too make sure the water pump is holding vacuum!
Well done K !
Herbert lee kwan Thank you!
Very well explained 👍
Tufail Ahmed Thank you!
Great video! Well explained
@Driveinnauto Thank you!
A great presentation, thank you.
Vern Pasfield My Pleasure!!
I really appreciated .I had accident and both air bags deployed I already put new ones on it and I send my air bag module to repair they fix I put it back on but now I only have air bag system code b1330 electrical fuse pyrothecnical separator resistance to high .. . the fuse on the positive battery cable in top of the battery was blow out I get new one from Mercedes and installed new one I tough that was the air bag crash fuse but still the air bag code present is there any other fuse or crash sensor for the air bag system in any other place located ?. could you please tell me ?. I check in front of the van but I didn't found any crash sensor in front of the van. but both air bags were deployed .. . in the accident the adblue tank unit get dent the adblue tank was empty but I fill the adblue tank .. after I fill it up the adblue tank the van drove great. after 250 miles I get in dashboard start idle message .and now the van is in limp mode I have code p13e300 the number of possible engine start is limited due to a malfunction in the adblue system ....and I have this code too p152100 the starter was disabled by the exhaust aftertreament system .. please help me with any tips I really appreciate any help . i already clean the dpf after the regenerate of diesel particular filter I get message system is complete then I tried to reset the codes but their still present and the van still in limp mode . I really appreciated your help
@Mrjfox818 since the van was in an accident the problem could be caused by so many issues, make sure the airbag module was programmed! I recommend you taske it tto a pro mechanic who can diagnosed it for you
right . did you know where the air bags crash sensor are located to make air bags deployed in case of accident ? because srs module can't be reprogramed cause still code on it . b1330 that's why need to find out where srs crash sensors are located . in advance thank you for your help @@KITS_Auto_and_Truck_Repair
Why on my 2010 sprinter tank fuel pump runs with key on engine off and never stops running thank you great info
@stevehvac1 the low side fuel pump should come on when the key is turned on for a about 1 - 3 minutes then it should turn off, if it remains on constantly you should have it looked at, the issue might be a shorted wire etc..
Thank you much
Hi, I was wondering if you could help me out please. My van told me that my vehicle was only a half tank full of AdBlue, so I filled it to the top. After I done that, I still got a sign on my van saying “AdBlue system malfunction, Emergency mode in 415 mls”. What does this mean and how do I sort this out? Thank you 😊
@usmzn this means there is a malfunction on the Adblue system, I recommend you take it to a pro mechanic who can diagnose it for you!
@@KITS_Auto_and_Truck_Repair Thank you so much!
@@usmzn My Pleasure!
Excellent, thanks. I bought a Sprinter 313cdi 2.1L yesterday, and now notice it is is hissing on acceleration, producing a P0101 and P2BAC code on the OBD. I really don't know what is up with it, but from this video it has given me some hope.
Do you have any idea based on those codes and the hissing?
Greetings from Dublin, Ireland. J.
@jimkay8322 My Pleasure! you might have a boost leak!
@@KITS_Auto_and_Truck_Repair My browser history would point to that too. Thanks for confirming. And keep up the content, it''s very informative and well delivered.
@@Jim_Kay. My Pleasure!
Good job mon frere! I'm next!
rafik ellouzi Thank you mon frère I'm looking forward to replacing yours!
❤❤❤
@jamesa9356 thanks!
Thx brother im with u 4 ever
@KazibweRonald My Pleasure! Thanks
Really appreciate what your sharing here , my 2006 sprinter has the p0299 issue . It had other problems that I believed caused the issue ...firstly the air intake (plastic part) of the inlet manifold had a crack ...this caused carb to build up everywhere I've changed EGR , o2 sensor an intake and gave deep clean to everything I could access. I still have the fault next I'll get a smoke test done however i think it'll pass okay after inspections. IMO now it's turbo / actuator fault it looks like the electronic actuator is missing possibly removed is that common practice ? Or a bodged job to sell? the turbo used to work fine
Pathetic Media Studios Thanks and good luck with your van!
@@KITS_Auto_and_Truck_Repair thanks man hope you all best too excellent information here 👍
@@patheticmediastudios8868 My Pleasure!
@@KITS_Auto_and_Truck_Repair took a week to clear DPF through , but we are officially back up an running 🙌
@@patheticmediastudios8868 I'm glad to hear that!
Sehr gutes Video❤😊👌👌👌👍👍👍👍👍
@thomaskramer9820 Thank you!
Hi Deo, do you have any recommendation for a scan tool in the sub $1,000 range?
Mainly want it for my 2012 Sprinter, not a full time mechanic anymore, just want to be able to fix my van myself. Thanks
Matt Cochran you can get an autel scanner, they some good ones for about 900$
@@KITS_Auto_and_Truck_Repair Vote for Autel. Anything I should beware of if considering Topdon, & x-tool too?
I appreciate your videos, thanks for the help👍
@@mattcochran My Pleasure!!
Good on you, nice job
Bugzie-A1 Thank you!!
Great video
@ramosramos1403 Thank you!
Great video. I was hoping this was my issues. However I have the same code. P0299. I made a smoke tester but I could not find a leak. (I may need a better machine)
I did a vacuum system test and it won’t hold vacuum. After testing each line it appears that mine is possibly from a faulty wastegate solenoid where some of the vacuum lines connect. Any experience with this? Thanks in advance.
Chris Jeffery my pleasure! check your waste wastegate actuator, make sure it's not stuck!
@@KITS_Auto_and_Truck_Repair I pulled the vacuum hose off the back and tested it. Held vacuum and the rod would slide in when I pulled the vacuum and slide out when released. However I have not put a GoPro on while driving to see if it’s working through shifting the gears
@@chrisjeffery9779 ok! you might have a defective transducer!
Hi Deo , i have a 2015 sprinter 2500 . i dont know nothing about these van. drove it about 800 miles since bout it . i have no check engine light but what i notice is that i did not add any DEF fluid to since bought it and every time tries to add DEF i find out the tank is full . any clue of what might be going on here ? thank you
sam sam if there is nothing wrong with the van then don't worry about it, when there is a fault in the DEF system a light will come on on the Dash!
brilliant! Thank you!
Richard Castillo My Pleasure!!
in my 2016 m Benz Sprinter 2500 2.1 Diesel engine I have accident and both air bags were deployed I put new ones already . I replace air bag module also an I put new pyrofuse the one in top in the battery but still have srs code b1330 . is any crash srs sensor some where ? I look for impact sensor in front of the van but there is not impact sensors on it . any help I really appreciate
@Mrjfox818 you need to program the airbag module!
Maybe the boost leak will fix the dpf dtc cause the NOX sensor readings were wrong just saying I'm a duramax technician
@josephespinoza9354 That's possible, Good point my Friend!
Good work bro
Nice-oscar Thank you!
check engine flashing light mercedes sprinter 313 cdi 2008 manual and only pull the engine do you somehow know what problem it might have thank you in advance
@spartacusvasilebahica149 you might have a misfire!
good job thanks
dan man My Pleasure!!
Where are you located bro .? I want you fix my sprinter please
@manuelm.2692 I'm Located in Frederick MD, you can email me at kitsautoandtruckrepair@gmail.com to set up an appointment
👍🏻👍🏻👍🏻🌷nice job
Aymen Mohamed Thank you!!
We're u at I need a Mechanic I'm having the same problem but how got the computer for it
@georgecasmarin6175 if you are in Maryland, you can bring your vehicle to us for service, Email me at kitsautoandtruckrepair@gmail.com for shop info!
I would be much appreciate if replacing charge a cooler was shown how to. South Africa
@wsnxumalo6707 I have a separate video about charge air cooler replacement on this sprinter, I recommend you watch it!
What scan tool do you use?
@michaelsmith8171 I use the snapon zeus and the Autel ultra
Good
Graham Plant Thanks!
Hi bro good morning from here..please what cause sprinter 308 cdi 2004 model to have emergency stop after 100 meter drive
@odinalaigbo4401 did you get the ECM scanned?
@odinalaigbo4401 what codes do you have in memory!
@@KITS_Auto_and_Truck_Repair have not done the scan yet
Hi please what scan tool do you use
@beniduh1087 Hi I use the snapon zeus and the Autel ultra
Where are you located, my friend?
@xavierfernandez2657 I'm located in Frederick MD, you can send me an email at kitsautoandtruckrepair@gmail.com for shop info!
Grasias
Martin Arrieta My Pleasure!!
I have a sprinter that needs repair. How do I contact you?
@bobbythompson17 you can email me at kitsautoandtruckrepair@gmail.com to schedule an appointment, we are located in Frederick MD
IF NO FAULT ON STAR DIGNOSTIC COMPUTER BUT ENGINE LAMP ON DISPLAY UNDER ENGINE RUNING. WHAT IT CAN BE PLZ ? ENGINE 651 SPRINTER.
@ibrahimabdullah7793 if you have a 2.1L engine check your vacuum actuators for the turbo!
@rezasadein28 Thanks!
Why can’t you be in La. This is my issue. What’s too much to pay a mechanic for this?
@toninsanders it's gonna depend on how much the shop charges per hour
If it goes into limp mode you're going to get cokeing on the DPF. If they're driving it around like this too much it's never going to get to operating temperature to burn the soot off of the DPF and also without the DEF working it could possibly foul the exhaust system faster because the oily diesel fuel is not burning properly.
@TLH444 Great point!
Where you located
Vladimir Espinal I'm located in Dickerson MD, Email me at Deo@calleva.org for shop info!
Can you give me your contact info. I have a 2016 Suburban that I think needs a transmission replacement. I watched your video that was posted a year ago I have the exact same truck.
@babbyjusus9221 Hi we can replace the transmission on your truck, we are located in Frederick MD, you can email us at kitsautoandtruckrepair@gmail.com to schedule an appointment!
That’s the big hill haha.
Ivan Peterzell Yeah Lol!!
Hi, sorry no offence, but I would use smoke machine first to see the leakage not by pressing the break in gear and accelerated you put wear
to the transmission
robert cazacu it's called power braking! it doesn't damage the transmission as long as you do it right and not for a long time!
I have a problem passenger side flashing fast
@JoseRodriguez-qp1xx what do mean by passenger side flashing fast, are you talking about the turn signal?
INTVITIVE
@nickayivor8432 Good!
I need to get mo
Long Trow what do you want to get?
They are 2.2
@slowmotiontv999 they should be 2.1L
I like to no not
Long Trow What do you mean? I didn't understand your statement!
Wonder if he ever put it on the lift.
@BigRedEd Yes I did
I like your videos
@Vegasunitedpartybus-com Thank you!