Heat load in space is 19.9mbh,where has we added additional 2mbh heat load by means of fresh air directly behind the fcu hence 21.9mbh. Space generated heat load (zone load)=19.9mbh Fresh air generated heat load =2mbh Our system has to cool (zone load + freshair load) 19.9+2 mbh heat load in order to maintain room at 76 deg F .
I have a question which make me confused ! I want to calculate heating and cooling loads in a project ( actually it is artificial project in order to learn Carrier software) - My system is AHU - in the section of Central cooling - supply temperature is set on 58 F as default. First question is that " is there any optimum ( or range) temperature for this section ? On the other side, I want to simulate this system ( AHU) in PSYCHROMETRIC ANALYZER software - after the cooling coil, there is a place at which I have to enter a figure. Should these figure be the same ? ( I means SUPPLY temperature in Carrie and temperature after cooling coil in Psychrometric analyzer software ) . i would be grateful if you explain me about these two figures and their optimum value.
Thank you for the explanation course. Though I have a question about this exacr calculation run. You ended with about 20,000 BTUh cooling load for the 150 sq.ft. office space. This is average 133 BTUh per sq.ft. It is 3 times highe than the most conservative rule of thumb number.
Good Morning Sir, I am currently doing a Laboratory project that the labs are mostly filled with fume hoods and re-circulation of the air in the labs are not allowed. There is also a clean room which the pressure has to be kept at positive to prevent contamination. My question is when I am keying the OA requirement, the ASHRAE std of college/university lab and science lab for education is not applicable to the laboratory project I am doing and hence, what should I key in for the OA requirement? Appreciate if you could do a tutorial on laboratory project. Thank you so much! :)
Heat load in space is 19.9mbh,where has we added additional 2mbh heat load by means of fresh air directly behind the fcu hence 21.9mbh.
Space generated heat load (zone load)=19.9mbh
Fresh air generated heat load =2mbh
Our system has to cool (zone load + freshair load) 19.9+2 mbh heat load in order to maintain room at 76 deg F .
Good day sir! Where did you based the cooling S-stat and heating T-stat Setpoints in Zone Components in?
Awesome explanation of each and every point,much appreciated
Thanks for useful video, can yo mention the lin for climatic data software
dont need to strugle so mch in u values in actual practice u values u can get from architect or local autority
Allah aapku Khair Ka mamla farmaye . You are doing great job sir
You deserve more Likes and Views!!! Thank you bhai
Sir from which data book you're using the R values. Please share with us. Overall lecture is awesome. JazakAllah
Fine. Sir, How Can we set the weather location by "User Define " ? Like my own Country and City and Village.
Please share the R value for
polyurethane board insulation?
hot bitumen grade 4
Mortar
Kindly make a video on hvac design calculation using elite software
Awesome lecture....thank you for sharing
Really detailed explanation. I would like to learn the school project too
Smtechno.teachable.com
Excellent Teaching
Welcome back sir❤❤
Awesome video sir 👍.
Can you please tell me how to find out the winter preheating value?
How to enter monsoon condition in HAP as where fresh air load higher it should calculate on basis to monsoon
I have a question which make me confused !
I want to calculate heating and cooling loads in a project ( actually it is artificial project in order to learn Carrier software) - My system is AHU - in the section of Central cooling - supply temperature is set on 58 F as default. First question is that " is there any optimum ( or range) temperature for this section ?
On the other side, I want to simulate this system ( AHU) in PSYCHROMETRIC ANALYZER software - after the cooling coil, there is a place at which I have to enter a figure. Should these figure be the same ? ( I means SUPPLY temperature in Carrie and temperature after cooling coil in Psychrometric analyzer software ) .
i would be grateful if you explain me about these two figures and their optimum value.
Excellent explanation
how i can get your school project tutorial for HAP Calculations?
Thank you for the explanation course. Though I have a question about this exacr calculation run. You ended with about 20,000 BTUh cooling load for the 150 sq.ft. office space. This is average 133 BTUh per sq.ft. It is 3 times highe than the most conservative rule of thumb number.
Because we consider all posible sources of heat gain in sample project
Hi Sir, Can you please share me the PDF of steps of HAP
Sir why was the CP density equal to steel density in defining the roof ?
Good Morning Sir,
I am currently doing a Laboratory project that the labs are mostly filled with fume hoods and re-circulation of the air in the labs are not allowed. There is also a clean room which the pressure has to be kept at positive to prevent contamination. My question is when I am keying the OA requirement, the ASHRAE std of college/university lab and science lab for education is not applicable to the laboratory project I am doing and hence, what should I key in for the OA requirement? Appreciate if you could do a tutorial on laboratory project. Thank you so much! :)
Could please switch on the caption or subtitle because i am hearing impaired person
Could you please share the link of handbook?
Sir, can you share that notes...
could you please send to me the pdf file of your video? thank you
Very good explanation
good afternoon at the time 1:00:56 of the video, the formula is not appreciated, can someone provide it to me, thank you very much in advance
Where can i get ASHRE Climate Software?
Good morning sir
Thanks for the video sir
WHERE IS THE LINK OF DOWNLOAD HAP
How to down load ashrea climatic data software
did you get even am trying to find
Sir pls share that school project HAP video.
Purchase from smtechno.teachable.com
Thanks a lot
Sir...iam btech mechanical engineering graduate.currently working as Mep engineer. If any vacancies please let me know
Dear Sir. How to convert higher version hap file to lower version file.
Sir for the fire fighting any software
Welcome sir
In your complete course online, do you provide the user license software?
Hi, How can I find basic (manual) H.V.A.C calculations?
smtechno.teachable.com
Which one is better option udemy with 20$ or website with 39$??
Jazakallah Khair
Dear sir Pls explain how to open higher version file in lower version hap software
Higher version cannot be open in lower version
@@SMTECHNO-MEP Ok sir thank you so much.. Then any converter available for convert like autocad trueviewer .??
Bcz consultant sent in 5.1 version but i have 4.6 version only
brother i don't have 29 dollar to purchase this course can you offer me for a less price
Hap kinke liye h
Mechanical or electrical engineer ?
Mechanical
@@SMTECHNO-MEP electrical k liye kuch btaye
Visit us@ www.smtmep.com
need customer number and authorized code
wall thickness in 9" but you considered 8", please reply
9" including cement plaster
Thanks sir
your programs are very costlier.. everyone can not afford it
15:00
HAP A PROCHUR HAPA
30:00
40:00