Machine ke bare mai ak video bano ki setar aaut ho jaye to kese sentar milaye or badiya se jankari kese kiya kiya karna hota hai full video bano sar ji sui kitne andar hona chahiy kitne baahar hona chaiye
We encountered this problem on the HKS-3M Mayer machines: GB1 was so close to the needles that it was practically touching them, despite the TEMPI settings appearing to be correct. We had to either tighten or delay the motion by 3-4mm (relative to the drive shaft circumference). GB1 still seems to be almost gliding over the needles, but this adjustment seeks to improve performance slightly. Have you ever experienced this problem? How can we further improve the performance of GB1? Also, newer KM machines don’t come with TEMPI setting gauges; it is built into the pattern wheel casing. Are there any advantages to having these gauges separately?
I'm sorry I can't tell you the exact cause. It's hard to figure out the cause without checking the machine condition directly. I think you should check the following: It should be installed on the designated bar indicated on the pattern disc. Check the wear condition of the SHOG pusher bearing. Check the wear condition of the PUSH ROD ball pig. I'm sorry I can't answer you because I don't have information about the new KM machine.
영상 봐 주셔서 감사합니다. 8.3mm 6.5mm는 3Tempi 게이지 수치이며 기계 타입과 motion (gang no)번호에 따라 적용 수치가 달라집니다, 7.5mm 역시 기종과 모션 번호를 확인후 사용하셔야 정확합니다. 타이밍 설정시 게이지 수치도 중요하지만 기계 정지 위치가 무엇보다 중요하다고 봅니다.
Buenos dias soy de argentina y tengo una tricotera chocan mucho las barras es posibke este fuera de punto el cambio el video esta bien pero no entiendo la traduccion como podria hacer
Se explica en inglés en la sección de descripción del video de RUclips, así que consúltelo. Gracias por ver. No hablo muy bien el español, por lo que utilizo Google Translate, por lo que puede haber errores en la comunicación precisa. Pedimos disculpas por las molestias. Si los subtítulos en inglés no ayudan, por favor dénos su dirección de correo electrónico y le enviaremos una explicación traducida en español.
Only the gauge dimensions of each machine type are different and the setting method is the same.
4 года назад
Congratulations, I really appreciate it. I have subscribed here and I have an RUclips channel similar, if you want to know, it is named like, Conceitos de malharia na prática. Success for you!
깨알같은 저희회사 홍보에 감사드립니다.
한영기계에서 좋은 제품 공급해주셔 항상 감사드립니다.
게이지 한개에 모든 치수가 갖춰져있어서 편리합니다.
Machine ke bare mai ak video bano ki setar aaut ho jaye to kese sentar milaye or badiya se jankari kese kiya kiya karna hota hai full video bano sar ji sui kitne andar hona chahiy kitne baahar hona chaiye
Mai koriya machin calata hu 22gej monu wali hai machin 22gej machin ki full jamkari do
Top regulagem.
Thanks for watching the video
Nice👍
thank you
thankyou somuch . your videos are verymuch informative
Thank you for your good rating.
Very good knowledge sir 👍
Thank you for your encouragement.
@@WarpknittingTechniques needle bed setting information...
We encountered this problem on the HKS-3M Mayer machines: GB1 was so close to the needles that it was practically touching them, despite the TEMPI settings appearing to be correct. We had to either tighten or delay the motion by 3-4mm (relative to the drive shaft circumference). GB1 still seems to be almost gliding over the needles, but this adjustment seeks to improve performance slightly.
Have you ever experienced this problem?
How can we further improve the performance of GB1?
Also, newer KM machines don’t come with TEMPI setting gauges; it is built into the pattern wheel casing. Are there any advantages to having these gauges separately?
I'm sorry I can't tell you the exact cause. It's hard to figure out the cause without checking the machine condition directly.
I think you should check the following:
It should be installed on the designated bar indicated on the pattern disc.
Check the wear condition of the SHOG pusher bearing.
Check the wear condition of the PUSH ROD ball pig.
I'm sorry I can't answer you because I don't have information about the new KM machine.
Taun pati kaise lagaye
PLEASE SEND ME BRUSHING PROCESS FOR karl mayer KS 4 FBZ EBC-EAC WITH MICROFIBRE YARN
sorry. I have no information about the HKS 4 FBZ EBC machine.
How To Change Main Motor Belt
Replacing the main motor belt can be done easily by loosening the motor fixing bolts.
timing set kaena sar
Very good
Thank you
2템피에서 3템피로 변경시 7.5mm 게이지를 올리고 타이밍을 맞춘다는 것이죠?
가이이드 빽 상태 바늘 고점.
잘못 눌러서 삭제가 되었네요.
영상 봐 주셔서 감사합니다.
8.3mm 6.5mm는 3Tempi 게이지 수치이며 기계 타입과 motion (gang no)번호에 따라 적용 수치가 달라집니다,
7.5mm 역시 기종과 모션 번호를 확인후 사용하셔야 정확합니다.
타이밍 설정시 게이지 수치도 중요하지만 기계 정지 위치가 무엇보다 중요하다고 봅니다.
@@WarpknittingTechniques 정보 감사합니다.
👌👌🙏🙏🙏very good
Thank you.
Buenos dias soy de argentina y tengo una tricotera chocan mucho las barras es posibke este fuera de punto el cambio el video esta bien pero no entiendo la traduccion como podria hacer
Se explica en inglés en la sección de descripción del video de RUclips, así que consúltelo.
Gracias por ver.
No hablo muy bien el español, por lo que utilizo Google Translate, por lo que puede haber errores en la comunicación precisa.
Pedimos disculpas por las molestias.
Si los subtítulos en inglés no ayudan, por favor dénos su dirección de correo electrónico y le enviaremos una explicación traducida en español.
패턴휠 조직 각도를 보고 정확히 맞히는 동영상 제작도 해 주시면 어떨까 합니다.
템피 변경시 ....
내가 하는 일에 관심을 가지고 노력하시는 모습이 아름답습니다.
조직 번호에따라 높낮이가 제각각이라 어렵지만 노력해보겠습니다.
한태커플님은 영상 제작 능력이 대단하신데 저도 배우고 싶습니다.
생각하는 것과 표현하는 것은 다른 것 같습니다.
Hello sir muze aap se baat karni ha to ka sa Kara
hamase eemel dvaara sampark karen.
tricot7@naver.com
how to change wheels hks 3
Only the gauge dimensions of each machine type are different and the setting method is the same.
Congratulations, I really appreciate it. I have subscribed here and I have an RUclips channel similar, if you want to know, it is named like, Conceitos de malharia na prática. Success for you!
Please visit surat india. You can run a successful training and service shop here.
sumit agarwal Thank you for your support.
Sir hindi me nhi mil sakta language
halo ai em sori.
ham kaarravaee karenge taaki aap youtubai anuvaad ke maadhyam se upasheershak hindee mein dekh saken.
트리코트 정보를 배부고 싶은 1인 입니다.
한번 뵙고싶습니다.
저는 영상 제작을 배우고 싶습니다.
@@WarpknittingTechniques 저도 초보 유튜브라서 동영상 제작도 걸음마 단계 입니다. 😂 ㅋㅋ
Sir tricot tottho give me
Mi dic michinss wark op rate
Sorry. I don't know what your opinion means.
Can you get a job
There are currently no jobs in Korea.
Ok
Sir
WhatasApp numar
I'm a Korean.
sorry
It is difficult to talk on the phone because we cannot communicate verbally.