This was fantastic thank you... One question. When I tightened the blade into position... It doesnt matter how tight i tighten the screws i can still move it a little bit with my hand .. Any tips??
Perfect steps for adjusting the blades and lever switch! For some reason the moving blade won't adjust beyond a certain point which has a slight gap between the blades on my corded masters the cordless is set the closest.
Hello, I took my blades off to sharpen them and clean the clippers. After I put the blades back on, they dont cut anymore. they make a noise and the blades move but theyre not cutting. I tried to pull the tension spring to give it more tension but it didnt work. Can you tell me or show me in a video how to put the top blade back on over the pring to see if im doing it right? Please Help!!!!
Why is it that the masters never close to the first notch it’s always in the middle.. since that’s a fact do I just go straight to the 3rd notch from the close position or barley open it to the second notch and then proceed to the 3rd
@@NVTwistedProductions i have the cordless masters and i have tightened the screws all the way but can still move it with my fingers , you know what i could do ??
Hi Can you zero gap the Andis MLC straight from the box? I’m having problems with zero gapping the whole blade only half attends to zero gap and the other half doesn’t, I just don’t know why. As in the video it’s all straight but my isn’t. I’ve been told that I need to change the blade is that true? Any help will help. Stay safe.
My Andis Cordless Masters have gotten soo loud after like 6 months. They were always louder than the corded ones but not they are even louder. Any idea on what it can be? Tension?
Just bought these Andis Masters and i cannot get them anywhere near 0. The closest i can get it is like a 16th of an inch from being even with the bottom blade. Do you think this one might be deflective? No issue with 0 gapping my Andis trimmers. Good lookin on the lever tip!
Honestly its not worth zero gapping them in the first place. If you truly zero gap it it eats at the andis guards. Get it as close as you can without it eating your guards and you are good to go. It takes out the trimmer line no problem as long as you are not setting in your trimmer line harshly. Its a tapered blade anyway so if you want to remove harsh trimmer lines its better to use a fade blade or just use a different clipper. Personally I dont like setting harsh trimmer lines anyway so i never have an issue with this clipper.
@@Peter-hw1yx instead of putting it in like you are lining someone up.. Use it like a clipper and scoop slightly while making the line. Making a super perfect skin guideline is a waste of time. Why? Because you are going to fade that line out anyway. As long as both sides look similar you will have an even fade when its finished.
@@Peter-hw1yx you can a lot of people do it like that. Personally since i need to be efficient with my work i use a zero gapped trimmer first . If you use clipper first you will still need to go underneath it with a trimmer
I’ve used cord and just bought the cordless . I felt the same way but I think for the cord price is good. Cordless I think you are over paying maybe 30-60 $ plus it has no clips lol Andis products been good so far
nah the stiff lever is better to not accidentally hit it.
I loosened the lever a little now when I press on someone's head it pushes the teeth in .. I should have just left it
Very helpful!!! Thank you!!!
You're welcome!
It makes too much noise . We don't like it
This was fantastic thank you... One question. When I tightened the blade into position... It doesnt matter how tight i tighten the screws i can still move it a little bit with my hand .. Any tips??
I’m having that same issue don’t know what to do smh
@@lomaxcharles ugh
did you end up fixing it ??
i have the same problem
Perfect steps for adjusting the blades and lever switch! For some reason the moving blade won't adjust beyond a certain point which has a slight gap between the blades on my corded masters the cordless is set the closest.
Thanks for watching
Hello, I took my blades off to sharpen them and clean the clippers. After I put the blades back on, they dont cut anymore. they make a noise and the blades move but theyre not cutting. I tried to pull the tension spring to give it more tension but it didnt work. Can you tell me or show me in a video how to put the top blade back on over the pring to see if im doing it right? Please Help!!!!
Do you have a wired masters?
Can you do a video on how to make the lever stiff on the 66360 model
Why is it that the masters never close to the first notch it’s always in the middle.. since that’s a fact do I just go straight to the 3rd notch from the close position or barley open it to the second notch and then proceed to the 3rd
I have a Andis Master Clippers and when I cut the blade will some move when I have the clipper blade closed. How do I get it to stop moving.
I am going through the same.. When i gapped them and tightened... It still moves a bit when i nudge it with my fingers
@@NVTwistedProductions did yoi ever fix it ??
@@Alanisrael12 I ended up getting the cordless ones and they don't move like that
@@NVTwistedProductions i have the cordless masters and i have tightened the screws all the way but can still move it with my fingers , you know what i could do ??
any tips on how to quiet this machine it is way too loud 👂
I just put a few drops of oil and firmly but gently worked the lever on a daily until it became smooth
Does the clippers bite on your guards when you zero gap it?
It will a little in the beginning.
Hi
Can you zero gap the Andis MLC straight from the box? I’m having problems with zero gapping the whole blade only half attends to zero gap and the other half doesn’t, I just don’t know why.
As in the video it’s all straight but my isn’t.
I’ve been told that I need to change the blade is that true?
Any help will help.
Stay safe.
My Andis Cordless Masters have gotten soo loud after like 6 months. They were always louder than the corded ones but not they are even louder. Any idea on what it can be? Tension?
Not sure that seems to be a on going problem
I’ve seen videos how to adjust the sound, by adjusting the the screw on the side of the body, search for the videos regarding this issue
@@shannonlazcano8506 I think that's a corded trick
Would this make it easier to fade out the guide lines?
yes it would
Why do all these funny ass barbers zero gapping everything? They're good the way they are
U aint gonna get the bottow line out of a bald fade with them then 🤷🤷
@Rob Guy 100 pct.. Or he sure as heck aint doing fade work .... Bowl cuts and mullets
@@NVTwistedProductions 🤣🤣
Can you do a video on how to replace the lever?
Definitely
Q: Can this be done the same way for on Andis T Outliner as far as zero gapping?
Yep.
Yes You can! We will make a vid on it!
when I put the maximum 0 bites the nozzle, what should I do?
Just bought these Andis Masters and i cannot get them anywhere near 0. The closest i can get it is like a 16th of an inch from being even with the bottom blade. Do you think this one might be deflective? No issue with 0 gapping my Andis trimmers. Good lookin on the lever tip!
Honestly its not worth zero gapping them in the first place. If you truly zero gap it it eats at the andis guards. Get it as close as you can without it eating your guards and you are good to go. It takes out the trimmer line no problem as long as you are not setting in your trimmer line harshly. Its a tapered blade anyway so if you want to remove harsh trimmer lines its better to use a fade blade or just use a different clipper. Personally I dont like setting harsh trimmer lines anyway so i never have an issue with this clipper.
@@Mike-hy8cs I always set harsh lines with my trimmer. How do I stop?
@@Peter-hw1yx instead of putting it in like you are lining someone up.. Use it like a clipper and scoop slightly while making the line. Making a super perfect skin guideline is a waste of time. Why? Because you are going to fade that line out anyway. As long as both sides look similar you will have an even fade when its finished.
@@Mike-hy8cs should I just use my andis master then instead of my trimmer all together?
@@Peter-hw1yx you can a lot of people do it like that. Personally since i need to be efficient with my work i use a zero gapped trimmer first . If you use clipper first you will still need to go underneath it with a trimmer
Stop zero gaping every type of clipper youre just going to destroy them
What how
Nice video.
Thanks!
Why it’s so expensive bro
Not sure why they are
I’ve used cord and just bought the cordless . I felt the same way but I think for the cord price is good. Cordless I think you are over paying maybe 30-60 $ plus it has no clips lol
Andis products been good so far