I can't thank you enough! Thanks to your video, I managed to clean the vacuum motor that was stuck with dust, and now the robot is working. Now, I'm trying to figure out an issue with the lidar sensor that occasionally gives a warning that it stucked.
My Midea S8+ had a "Please clean the cliff sensor" alert despite cleaning it, I wanted to open it but couldn't figure out how, thanks to this video I managed to open it and turns out 1 cable was snapped somehow, soldered it and working again, also allowed me to clean it properly inside. Thank you!
Thank you very much for this video. Last month a tried to fix my robot (one wheel wasn't working) and i couldn't open it nor find any video for it. Now thanks to you it's already cleaning my house. Thanks once more!
@@RobertDekker I've already bought a new wheel and just replaced the old one. But out of curiosity i've opened it today and everything looks alright (gears are intact). I think it's just the motor that broke - i can still rotate the wheel but it's very difficult to do so.
@@RobertDekker In my case the wool inside the gearbox made it difficult to rotate the wheel. But I know from 4pda.ru forum that another cause of wheel turn problems is motor failure.
@@headphone112 I think you can find them on aliexpress, but I wanna open the thing myself before buying parts, so I can't confirm. Wouldn't like to buy the wheel intead of the motor because of bad translations and such. Did you end up doing the repair too?
I have one wheel that does not function and I could not get the cover off (what you did with the wooden tool). This video shows clearly how to remove the cover. Thanks!
Mine isn't charging. I cleaned the contacts and sensors. the multimeter says that the base is putting out electricity. I swapped in a new battery. would opening it up and cleaning it help. customer service says it's an internal issue but won't say what internal issue.
I am also having that issue. customer service told me the same thing. Cleaned the contacts this helped a couple of times but not long term solution. I changed the battery. I put a multimeter on both sets of contacts. On the device I get a .7 someting reading in diode mode and the charger gives 16 sometimes. At first it would give 16 while the springs were up but after I took it apart and cleaned and tweaked they now give a 16 only when down. Neither way is charging device. One thing I haven't tried is popping off the front wheel to see if maybe it got something tangled under it to hold it away from being fully seated. Read some where this could contribute to a charging issue. I can't pry it up. Does anyone know how??
Hi mine has stopped charging🙃. I Cleaned the contacts this helped a couple of times but no longer. I changed the battery. I put a multimeter on both sets of contacts. On the device I get a .7 someting reading in diode mode and the charger gives 16 sometimes when measuring DC voltage. This is where it gets confusing. At first it would give a reading only while the contacts were up but after I took it apart and cleaned and tweaked a little they now give a reading only when pressed down . Still not charging One thing I haven't tried is popping off the front wheel to see if something is holding it away from being fully seated. Read some where this could contribute to a charging issue. I can't pry it up. Does anyone know how to remove and reinstall?? Or let me know if there is something else to try or an expert to consult. Please and Thank you.
Hola, después de desmontar el midea M7 no vuelve a encender. Le ha pasado a alguien? Hay algun procedimiento especial de encendido? Gracias de antemano
Hello mate, i have this model I get this error WIPE THE CLIFF SENSOR I do, but still the problem remains, it looks like those are damaged, do You know where can i get a replacement?
First thing the wet mode doesn’t work! Even when brand new and after 12 months the base charger burnt out and luckily it doesn’t burn a hole in my carpet but it does burn the vacuum base contact though! Midea Melbourne office refused warranty and told me to send it back to Amazon USA and it ll cost me $200 to mail it back! Useless!!!
Vidéo sans aucun intérêt, car il démonte à toute vitesse en cachant les emplacements des vis. Je voulais savoir comment démonter une roue motrice pour la nettoyer, la décoincer, mais je n'ai rien vu. Qui a besoin de savoir comment on demonte "entierement" la machine ?
I can't thank you enough! Thanks to your video, I managed to clean the vacuum motor that was stuck with dust, and now the robot is working. Now, I'm trying to figure out an issue with the lidar sensor that occasionally gives a warning that it stucked.
My Midea S8+ had a "Please clean the cliff sensor" alert despite cleaning it, I wanted to open it but couldn't figure out how, thanks to this video I managed to open it and turns out 1 cable was snapped somehow, soldered it and working again, also allowed me to clean it properly inside.
Thank you!
Muchisimas gracias, me sirvio para reparar mi aspiradora, saludos desde Mexico!
Thank you very much for this video. Last month a tried to fix my robot (one wheel wasn't working) and i couldn't open it nor find any video for it. Now thanks to you it's already cleaning my house. Thanks once more!
Did you only have to clean the wheel?
@@RobertDekker I've already bought a new wheel and just replaced the old one. But out of curiosity i've opened it today and everything looks alright (gears are intact). I think it's just the motor that broke - i can still rotate the wheel but it's very difficult to do so.
@@RobertDekker In my case the wool inside the gearbox made it difficult to rotate the wheel. But I know from 4pda.ru forum that another cause of wheel turn problems is motor failure.
I read that a lot of this type of vacuums have the stuck wheel problem. Where did you buy a new wheel? Mine is stuck too
@@headphone112 I think you can find them on aliexpress, but I wanna open the thing myself before buying parts, so I can't confirm. Wouldn't like to buy the wheel intead of the motor because of bad translations and such.
Did you end up doing the repair too?
Thanks for your tutorial very help me
Mine says "please clean the lidar", and that it's stuck, when it's clearly not.
У меня тоже самое. Упал на лидар и теперь лидар не вращается и пишет эту ошибку
Спасибо, Брат
у меня основная щетка не крутится - даже вручную не провернуть. это сгорел мотор?
M7 Robot süpürgemi nasıl kullanabilirim
Hi, a buy one on ebay, but this no drop the watter, do you know how I can do?
I disassambled the mini pump on mine. the rubber hoses were swapped. I connected them correctly and now everything works.
I have one wheel that does not function and I could not get the cover off (what you did with the wooden tool). This video shows clearly how to remove the cover. Thanks!
Mine isn't charging. I cleaned the contacts and sensors. the multimeter says that the base is putting out electricity. I swapped in a new battery. would opening it up and cleaning it help. customer service says it's an internal issue but won't say what internal issue.
I am also having that issue. customer service told me the same thing. Cleaned the contacts this helped a couple of times but not long term solution. I changed the battery. I put a multimeter on both sets of contacts. On the device I get a .7 someting reading in diode mode and the charger gives 16 sometimes. At first it would give 16 while the springs were up but after I took it apart and cleaned and tweaked they now give a 16 only when down. Neither way is charging device. One thing I haven't tried is popping off the front wheel to see if maybe it got something tangled under it to hold it away from being fully seated. Read some where this could contribute to a charging issue. I can't pry it up. Does anyone know how??
Hi mine has stopped charging🙃. I Cleaned the contacts this helped a couple of times but no longer. I changed the battery. I put a multimeter on both sets of contacts. On the device I get a .7 someting reading in diode mode and the charger gives 16 sometimes when measuring DC voltage. This is where it gets confusing. At first it would give a reading only while the contacts were up but after I took it apart and cleaned and tweaked a little they now give a reading only when pressed down . Still not charging One thing I haven't tried is popping off the front wheel to see if something is holding it away from being fully seated. Read some where this could contribute to a charging issue. I can't pry it up. Does anyone know how to remove and reinstall?? Or let me know if there is something else to try or an expert to consult. Please and Thank you.
Hola, después de desmontar el midea M7 no vuelve a encender. Le ha pasado a alguien? Hay algun procedimiento especial de encendido? Gracias de antemano
Thank you! I also have the stuck wheel problem and still haven't had the chance to work on it. This video is gonna save a lot of time
Same thing happens to me although nothing stuck in the wheel. Looks like the bearings issue it produces squeaking sound
Thank you very much for the explanation ❤🎉
Hello mate, i have this model
I get this error
WIPE THE CLIFF SENSOR
I do, but still the problem remains, it looks like those are damaged, do You know where can i get a replacement?
thank you. I need to tie the front wheel that is getting loose
Hello .Do you have any information about model of motor used to main brush rpm voltage
Show me continuously the message clean the radar and stop to working,maybe you know what I should do?
Thank you in advance
Mine is doing this too, did you find anything that works?
Спасибо тебе дорогой. Могу сказать только будьте аккуратнее с шлейфами. У меня один развалился. Предварительно их нужно покачать
Thank you
Подскажите, как чинить пылесборник? Помыла его, только потом прочитала, что нельзя. Теперь выдает ошибку, что поместите пылесборник.
First thing the wet mode doesn’t work! Even when brand new and after 12 months the base charger burnt out and luckily it doesn’t burn a hole in my carpet but it does burn the vacuum base contact though! Midea Melbourne office refused warranty and told me to send it back to Amazon USA and it ll cost me $200 to mail it back! Useless!!!
Vidéo sans aucun intérêt, car il démonte à toute vitesse en cachant les emplacements des vis. Je voulais savoir comment démonter une roue motrice pour la nettoyer, la décoincer, mais je n'ai rien vu. Qui a besoin de savoir comment on demonte "entierement" la machine ?
I think I won't buy products of these people. They are so very insecure that they make it extremely difficult for even experts to open their machine
This devices are destined to fail at one time or another, mine throws this error:
Wipe the cliff sensor
I do and still the issue remains